This Appendix describes the test procedure to determine exhaust emissions from light passenger and commercialThe vehicle survey shall be used in order to select properly maintained and used vehicles using a Portable Emissions Measurement System.
≤smaller or equal
#number
#/m3number per cubic metre
%per cent
°Cdegree centigrade
ggramme
g/sgramme per second
hhour
Hzhertz
Kkelvin
kgkilogramme
kg/skilogramme per second
kmkilometre
km/hkilometre per hour
kPakilopascal
kPa/minkilopascal per minute
llitre
l/minlitre per minute
mmetre
m3cubic-metre
mgmilligram
minminute
peevacuated pressure [kPa]
qvsvolume flow rate for testing in ISC. Vehicles that have one or more of the system [l/min]
ppmparts per million
ppmC1parts per million carbon equivalent
rpmrevolutions per minute
ssecond
Vssystem volume [l]
The test exclusion criteria below shall be carried out with a PEMS, composed of components specified in points 3.1.1 to 3.1.5. If applicable, a connection with the vehicle ECU may be established to determine relevant engine and vehicle parameters as specified in point 3.2.
3.1.1. Analysers to determine the concentration of pollutants in the exhaust gas.
3.1.2. One or multiple instruments or sensors to measure or determine the exhaust mass flow.
3.1.3. A Global Positioning System to determine the position, altitude and, speed of the vehicle.
3.1.4. If applicable, sensors and other appliances being not part of the vehicle, e.g., to measure ambient temperature, relative humidity, air pressure, and vehicle speed.
3.1.5. An energy source independent of the vehicle to power the PEMS.
Test parameters as specified in Table 1 of this Appendix shall be measured, recorded at a constant frequency of 1.0 Hz or higher and reported according to the requirements of Appendix 8. If ECU parameters are obtained, these should be made available at a substantially higher frequency than the parameters recorded by PEMS. The PEMS analysers, flow-measuring instruments and sensors shall excluded from testing or otherwise repaired and then selected.
Confidential
Date: | | | x
Name of investigator: | | | x
Location of test: | | | x
Country of registration (in EU only): | | x |
x = Exclusion Criteria | X = Checked and reported |
Vehicle Characteristics |
Registration plate number: | | x | x
Mileage and age of vehicle:
The vehicle must comply with the requirements laid down in Appendices 2 and 3 of this Annex.
[to be measured on a wet basis or to be corrected as described in point 8.1 of Appendix 4] [to be determined only if indirect methods are used to calculate exhaust mass flow rate as described in paragraphs 10.2 and 10.3 of Appendix 4] [method to be chosen according to point 4.7] [parameter only mandatory if measurement required by Annex IIIA, section 2.1] [to be determined only if necessary to verify rules in regards to mileage and age in Article 9, otherwise it cannot be selected. The age of the vehicle status and operating conditions] [may be calculated counts from THC and CH4 concentrations according to point 9.2 of Appendix 4] [may be calculated from measured NO and NO2 concentrations] [Multiple parameter sources may be used.] [The preferable source is the ambient pressure sensor.]
Parameter | Recommended unit | Source
THC concentration, | ppm C1 | Analyser
CH4 concentration, | ppm C1 | Analyser
NMHC concentration, | ppm C1 | Analyser
CO concentration, | ppm | Analyser
CO2 concentration | ppm | Analyser
NOX concentration, | ppm | Analyser
PN concentration | #/m3 | Analyser
Exhaust mass flow rate | kg/s | EFM, any methods described in point 7 of Appendix 2
Ambient humidity | % | Sensor
Ambient temperature | K | Sensor
Ambient pressure | kPa | Sensor
Vehicle speed | km/h | Sensor, GPS, or ECU
Vehicle latitude | Degree | GPS
Vehicle longitude | Degree | GPS
Vehicle altitude, | M | GPS or Sensor
Exhaust gas temperature | K | Sensor
the date of first registration
x | |
Date of first registration: | | x |
VIN: | | x | x
Emission class and character: | | x |
Country of registration:
The vehicle must be registered in the EU
x | x |
Model: | | x |
Engine code: | | x |
Engine volume (l): | | x |
Engine coolant temperature | K | Sensor or ECU
Engine speed | rpm | Sensor or ECU
Engine torque | Nm | Sensor or ECU
Torque at driven power (kW): | | x |
Gearbox type (auto/manual): | | x |
Drive axle | Nm | Rim torque meter
Pedal position | % | Sensor or ECU
Engine fuel flow | g/s | Sensor or ECU
Engine intake air flow | g/s | Sensor or ECU
Fault status | — | ECU
Intake air flow temperature | K | Sensor or ECU
Regeneration status | — | ECU
Engine oil temperature | K | Sensor or ECU
Actual gear | # | ECU
Desired gear (e.g. gear shift indicator) | # | ECU
Other vehicle data | unspecified | ECU
The preparation of the vehicle shall include a general verification of the correct technical functioning (FWD/AWD/RWD): | | x |
Tyre size (front and rear if different): | | x |
Is the vehicle involved in a recall or service campaign?
If yes: Which one? Has the campaign repairs already been done?
The repairs must have been done before the start of the test vehicle.
The installation of the PEMS shall follow the instructions of the PEMS manufacturer and the local health and safety regulations. The PEMS should be installed as to minimise during the test electromagnetic interferences as well as exposure to shocks, vibration, dust and variability in temperature. The installation and operation ISC testing
x | x |
Vehicle Owner Interview
(the owner will only be asked the main questions and shall have no knowledge of the PEMS shall be leak-tight and minimise heat loss. The installation and operation of PEMS shall not change the natureimplications of the replies)
Name of the exhaust gas nor unduly increase the length of the tailpipe. To avoid the generation of particles, connectors shall be thermally stable at the exhaust gas temperatures expected during the test. It is recommended not to use elastomer connectors to connect owner (only available to the accredited inspection body or laboratory/technical service) | | | x
Contact (address / telephone) (only available to the accredited inspection body or laboratory/technical service) | | | x
How many owners did the vehicle exhaust outlet and the connecting tube. Elastomer connectors, if used, shall have no contact with the exhaust gas to avoid artefacts at high engine load.
The installation and operation of the PEMS sampling probes shall not unduly increase the pressure at the exhaust outlet in a way that may influence the representativeness have? | | x |
Did the odometer not work?
If yes, the vehicle cannot be selected.
x | |
Was the vehicle used for one of the measurements. It is thus recommended that only one sampling probe is installed in the same plane. If technically feasible, any extension to facilitate the sampling or connection with the exhaust mass flow meter shall have an equivalent, or larger, cross sectional area than the exhaust pipe. If the sampling probes obstruct a significant area following? | | |
As car used in show-rooms? | | x |
As a taxi? | | x |
As delivery vehicle? | | x |
For racing / motor sports? | x | |
As a rental car? | | x |
Has the vehicle carried heavy loads over the specifications of the tailpipe cross-section, backpressure measurement may be requested by the Type Approval Authority.
Whenever used, the exhaust mass flow meter shall be attached to the manufacturer?
If yes, the vehicle cannot be selected.
x | |
Have there been major engine or vehicle’s tailpipe(s) in accordance with the recommendations of the EFM manufacturer. The measurement range of the EFM shall match the range of the exhaust mass flow rate expected during the test. The installation of the EFM and any exhaust pipe adaptors or junctions shall not adversely affect the operation repairs? | | x |
Have there been unauthorised major engine or vehicle repairs?
If yes, the vehicle cannot be selected.
x | |
Has there been an unauthorised power increase/tuning?
If yes, the vehicle cannot be selected.
x | |
Was any part of the engine or exhaust emissions after-treatment system. A minimum of four pipe diameters or 150 mm of straight tubing, whichever is larger, shall be placed at either side of the flow-sensing element. When testing a multi-cylinder engine with a branched exhaust manifold, it is recommended to position the exhaust mass flow meter downstream of where the manifolds combine and to increase the cross section and/or the fuel system replaced? Were original parts used? If original parts were not used, the vehicle cannot be selected. | x | x |
Was any part of the piping such as to have an equivalent, or larger, cross sectional area from which to sample. If this is not feasible, exhaust flow measurements with several exhaust mass flow meters may be used, if approved by the Type Approval Authorities. The wide variety of exhaust pipe configurations, dimensions and exhaust mass flow rates may require compromises, guided by good engineering judgement, when selecting and installing the EFM(s). It is permissible to install an EFM with a diameter smaller than that of the exhaust outlet or the total cross-sectional area of multiple outlets, providing it improves measurement accuracy and does not adversely affect the operation or the exhaust after-treatment as specified in point 3.4.2. It is recommended to document the EFM set-up using photographs.
The GPS antenna should be mounted, e.g. at the highest possible location, as to ensure good reception of the satellite signal. The mounted GPS antenna shall interfere as little as possible with the vehicle operation.
If desired, relevant vehicle and engine parameters listed in Table 1 can be recorded by using a data logger connected with the ECU or the vehicle network through standards, such as ISO 15031-5 or SAE J1979, OBD-II, EOBD or WWH-OBD. If applicable, manufacturers shall disclose labels to allow the identification of required parameters.
Vehicle speed sensors, temperature sensors, coolant thermocouples or any emissions after-treatment system permanently removed?
If yes, the vehicle cannot be selected
x | |
Were there any unauthorised devices installed (Urea killer, emulator, etc)?
If yes, the vehicle cannot be selected
x | |
Was the vehicle involved in a serious accident? Provide a list of damage and repairs done afterwards | | x |
Has the car been used with a wrong fuel type (i.e. gasoline instead of diesel) in the past? Has the car been used with non-commercially available EU-quality fuel (black market, or blended fuel?)
If yes, the vehicle cannot be selected.
x | |
Did you use air-freshener, cockpit-spray, brake cleaner or other measurement device not part ofhigh hydrocarbon emission source around the vehicle shall be installed to measure the parameter under consideration in a representative, reliable and accurate manner without unduly interfering with during the last month? If yes, the vehicle operation and the functioning of other analysers, flow-measuring instruments, sensors and signals. Sensors and auxiliary equipment shall be powered independently of the vehicle. It is permitted to power any safety-related illumination of fixtures and installations of PEMS components cannot be selected for evaporative testing. | x | |
Was there a gasoline spill in the inside or outside of the vehicle’s cabin by the vehicle’s battery.
Emissions sampling shall be representative and conducted at locations of well-mixed exhaust where the influence of ambient air downstream of the sampling point is minimal. If applicable, emissions shall be sampled downstream of the exhaust mass flow meter, respecting a distance of at least 150 mm to the flow sensing element. The sampling probes shall be fitted at least 200 mm or three times the inner diameter of the exhaust pipe, whichever is larger, upstream of the point at which the exhaust exits the PEMS sampling installation into the environment. If the PEMS feeds back a flow to the tail pipe, this shall occur downstream of the sampling probe in a manner that does not affect during engine operation the nature of the exhaust gas at the sampling point(s). If the length of the sampling line is changed during the last 3 months?
If yes, the vehicle cannot be selected for evaporative testing.
x | |
Did anyone smoke in the car during the last 12 months?
If yes, the vehicle cannot be selected for evaporative testing
x | |
Did you apply corrosion protection, stickers, under seal protection, on any other potential sources of volatile compounds to the car?
If yes, the system transport times shall be verified and if necessary corrected.
If the engine is equipped with an exhaust after-treatment systemvehicle cannot be selected for evaporative testing
x | |
Was the car repainted?
If yes, the exhaust sample shall be taken downstream of the exhaust after-treatment system. When testing avehicle cannot be selected for evaporative testing
x | |
Where do you use your vehicle with a branched exhaust manifold, the inlet of the sampling probe shall be located sufficiently far downstream so as to ensure that the sample is representative of the average exhaust emissions of all cylinders. In multi-cylinder engines, having distinct groups of manifolds, such as more often? | | |
% motorway | | x |
% rural | | x |
% urban | | x |
Did you drive the vehicle in a ‘V’ engine configuration, the sampling probe shall be positioned downstream of where the manifolds combine. If this is technically not feasible, multi-point sampling at locations of well-mixed exhaust may be used, if approved by the Type Approval Authority. In this case, the number and location of sampling probes shall match as far as possible those of the exhaust mass flow meters. In case of unequal exhaust flows, proportional sampling or sampling with multiple analysers shall be considered.
If particles are measured, the exhaust shall be sampled from the centre of the exhaust stream. If several probes are used for emissions samplingnon EU Member State for more than 10 % of driving time?
If yes, the vehicle cannot be selected
x | — |
In which country was the vehicle refuelled during the last two times?
If the vehicle was refuelled the last two times outside a state applying the EU Fuel Standards, the particle sampling probe should be placed upstream of the other sampling probes. The particle sampling probe should not interfere with the sampling of gaseous pollutants. The type and specifications of the probe and its mounting shall be documented in detail.
If hydrocarbons are measured, the sampling line shall be heated to 463 ± 10 K (190 ± 10 °C). For the measurement of other gaseous components with or without coolervehicle cannot be selected.
x | |
Has a fuel additive, not approved by the manufacturer been used?
If yes then the vehicle cannot be selected.
x | |
Has the vehicle been maintained and used in accordance with the manufacturer's instructions?
If not, the sampling line shall be kept at a minimum of 333 K (60 °C) to avoid condensation and to ensure appropriate penetration efficiencies of the various gases. For low pressure sampling systemsvehicle cannot be selected.
x | |
Full service and repair history including any re-works
If the full documentation cannot be provided, the temperature can be lowered corresponding to the pressure decrease provided that the sampling system ensures a penetration efficiency of 95 % for all regulated gaseous pollutants. If particles are sampled and not diluted at the tailpipe, the sampling line from the raw exhaust sample point to the point of dilution or particle detector shall be heated to a minimum of 373 K (100 °C). The residence time of the sample in the particle sampling line shall be less than 3 s until reaching first dilution or the particle detector.
All parts of the sampling system from the exhaust pipe up to the particle detector, which are in contact with raw or diluted exhaust gas, shall be designed to minimize deposition of particles. All parts shall be made from antistatic material to prevent electrostatic effects.
After the installation of the PEMS is completed, a leak check shall be performed at least once for each PEMS-vehicle cannot be selected.
x | |
Vehicle Examination and Maintenance |
X = Exclusion Criteria/
F = Faulty Vehicle
X = checked and reported
1 |
Fuel tank level (full / empty)
Is the fuel reserve light ON? If yes, refuel before test.
x
2 |
Are there any warning lights on the instrument panel activated indicating a vehicle installation as prescribed by the PEMS manufacturer or as follows. The probe shall be disconnected from the or exhaust after-treatment system and the end plugged. The analyser pump shall be switched on. After an initial stabilization period all flow meters shall read approximately zero in the absence of a leak. Elsemalfunctioning that cannot be resolve by normal maintenance? (Malfunction Indication Light, Engine Service Light, etc?)
If yes, the sampling lines shall be checked and the fault be corrected.
The leakage rate on the vacuum side shall not exceed 0.5 per cent of the in-use flow rate for the portion of the system being checked. The analyser flows and bypass flows may be used to estimate the in-use flow rate.
Alternatively, the system may be evacuated to a pressure of at least 20 kPa vacuum (80 kPa absolute). After an initial stabilization period the pressure increase Δp (kPa/min) in the system shall not exceed:
ΔppeVs qvs 0.005
Alternatively, a concentration step change at the beginning of the sampling line shall be introduced by switching from zero to span gas while maintaining the same pressure conditions as under normal vehicle cannot be selected
x |
3 |
Is the SCR light on after engine-on?
If yes, the AdBlue should be filled in, or the repair executed before the vehicle is used for testing.
x |
4 |
Visual examination exhaust system operation. If for a correctly calibrated analyser after an adequate period of time the reading is ≤ 99 per cent compared to the introduced concentration, the leakage problem shall be corrected.
The PEMS shall be switched on, warmed up and stabilized in accordance with the specifications of the PEMS manufacturer until key functional parameters, e.g., pressures, temperatures and flows have reached their operating set points before test start. To ensure correct functioning
Check leaks between exhaust manifold and end of tailpipe. Check and document (with photos)
If there is damage or leaks, the PEMS may be kept switched on or can be warmed up and stabilized during vehicle conditioning. The system shall be free of errors and critical warnings.
The sampling system, consisting of the sampling probe and sampling lines shall be prepared for testing by following the instruction of the PEMS manufacturer. It shall be ensured that the sampling system is clean and free of moisture condensation.
If used for measuring the exhaust mass flow, the EFM shall be purged and prepared for operation in accordance with the specifications of the EFM manufacturer. This procedure shall, if applicable, remove condensation and deposits from the lines and the associated measurement ports.
Zero and span calibration adjustments of the analysers shall be performed using calibration gases that meet the requirements of point 5 of Appendix 2. The calibration gases shall be chosen to match the range of pollutant concentrations expected during the RDE test. To minimize analyser drift, one should conduct the zero and span calibration of analysers at an ambient temperature that resembles, as closely as possible, the temperature experienced by the test equipment during the trip.
The zero level of the analyser shall be recorded by sampling HEPA filtered ambient air at an appropriate sampling point, usually at the inlet of the sampling line. The signal shall be recorded at a constant frequency of at least 1,0 Hz averaged over a period of 2 minutes; the final concentration shall be within the manufacturer’s specifications, but shall not exceed 5000 particles per cubic-centimetre.
Vehicle speed shall be determined by at least one of the following methods:
(a) a GPS; if vehicle speed is determined by a GPSis declared faulty.
F |
5 |
Exhaust gas relevant components
Check and document (with photos) all emissions relevant components for damage.
If there is damage, the vehicle is declared faulty.
F |
6 |
Evaporative system
Pressurize fuel-system (from canister side), testing for leaks in a constant ambient temperature environment, FID sniff test around and in the vehicle. If the FID sniff test is not passed, the vehicle is declared faulty.
F |
7 |
Fuel sample
Collect fuel sample from the fuel tank.
x
8 |
Air filter and oil filter
Check for contamination and damage and change if damaged or heavily contaminated or less than 800 km before the next recommended change.
x
9 |
Window washer fluid (only for evaporative testing)
Remove window washer fluid and fill tank with hot water.
x
10 |
Wheels (front & rear)
Check whether the wheels are freely moveable or blocked by the brake.
If not, the total trip distance shall be checked against the measurements of another method according to point 7 of Appendix 4.
(b) a sensor (e.g., optical or micro-wave sensor); if vehicle speed is determined by a sensor, the speed measurements shall comply with the requirements of point 8 of Appendix 2, or alternatively, the total trip distance determined by the sensor shall be compared with a reference distance obtained from a digital road network or topographic map. The total trip distance determined by the sensor shall deviate by no more than 4 % from the reference distance.
(c) the ECU; if vehicle speed is determined by the ECU, the total trip distance shall be validated according to point 3 of Appendix 3 and the ECU speed signal adjusted, if necessary to fulfil the requirements of point 3.3 of Appendix 3. Alternatively, the total trip distance as determined by the ECU can be compared vehicle cannot be selected.
x |
11 |
Tyres (only for evaporative testing)
Remove spare tyre, change to stabilised tyres if the tyres were changes less than 15000 km ago. Use summer and all season tyres only.
x
12 |
Drive belts & cooler cover
In case of damage, the vehicle is declared faulty. Document with a reference distance obtained from a digital road network or topographic map. The total trip distance determined by the ECU shall deviate by no more than 4 % from the reference.
The correctness of connections with all sensors and, if applicable, the ECU shall be verified. If photos
F |
13 |
Check fluid levels
Check the max. and min. levels (engine parameters are retrieved, it shall be ensured that the ECU reports values correctly (e.g., zero engine speed [rpm] while the combustion engine is in key-on-engine-off status). The PEMS shall function oil, cooling liquid) / top up if below minimum
x
14 |
Filler flap (only for evaporative testing)
Check overfill line within filler flap is completely free of errors and critical warnings.
Sampling, measurement and recording of parameters shall begin prior to the ‘ignition on’ of the engine. To facilitate time alignment, it is recommended to record the parameters that are subject to time alignment either by a single data recording device or residues or flush the hose with a synchronised time stamp. Before and directly after ‘ignition on’, it shall be confirmed that all necessary parameters are recorded by the data logger.
Sampling, measurement and recording of parameters shall continue throughout the on-road test of the vehicle. The engine may be stopped and started, but emissions sampling and parameter recording shall continue. Any warning signals, suggesting malfunctioning of the PEMS, shall be documented and verified. If any error signal(s) appear during the test, the test shall be voided. Parameter recording shall reach a data completeness of higher than 99 %. Measurement and data recording may be interrupted for less than 1 % of the total trip duration but for no more than a consecutive period of 30 s solely in the hot water.
x
15 |
Vacuum hoses and electrical wiring
Check all for integrity. In case of damage, the vehicle is declared faulty. Document with photos
F |
16 |
Injection valves / cabling
Check all cables and fuel lines. In case of damage, the vehicle is declared faulty. Document with photos
F |
17 |
Ignition cable (gasoline)
Check spark plugs, cables, etc. In case of damage, replace them.
x
18 |
EGR & Catalyst, Particle Filter
Check all cables, wires and sensors.
In case of unintended signal loss or for the purpose of PEMS system maintenance. Interruptions may be recorded directly by the PEMS but it is not permissible to introduce interruptions in the recorded parameter via the pre-processing, exchange or post-processing of data. If conducted, auto zeroing shall be performed against a traceable zero standard similar to the one used to zero the analyser. It is strongly recommended to initiate PEMS tampering, the vehicle cannot be selected.
In case of damage the vehicle is declared Faulty, Document with photos
x/F |
19 |
Safety condition
Check tyres, vehicle's body, electrical and braking system maintenance during periods of zero vehicle speed.
The end of status are in safe conditions for the test is reached when the vehicle has completed the trip and the ignition is turned off. Excessive idling of the engine after the completion of the trip shall be avoided. The data recording shall continue until the response time of the sampling systems has elapsed.
The zero and span of the analysers of gaseous components shall be checked by using calibration gases identical to the ones applied under point 4.5 to evaluate the analyser's zero and response drift compared to the pre-test calibration. It is permissible to zero the analyser prior to verifying the span drift, if the zero drift was determined to be within the permissible range. The post-test drift check shall be completed as soon as possible after the test and before the PEMS, or individual analysers or sensors, are turned off or have switched into a non-operating mode. The difference between the pre-test and post-test results shall comply and respect road traffic rules.
If not, the vehicle cannot be selected.
x |
20 |
Semi-trailer
Are there electric cables for semi-trailer connection, where required?
x
21 |
Aerodynamic modifications
Verify no aftermarket aerodynamics modification that cannot be removed before testing was made (roof boxes, load racking, spoilers, etc.) and no standard aerodynamics components are missing (front deflectors, diffusers, splitters, etc.).
If yes, the vehicle cannot be selected. Document with the requirements specified in Table 2.
[If the zero drift is within the permissible range, it is permissible to zero the analyser prior to verifying the span drift.]
Pollutant | Absolute Zero response drift | Absolute Span response drift
CO2 | ≤ 2000 ppm per test | ≤ 2 % of reading or ≤ 2000 ppm per test, whichever is larger
CO | ≤ 75 ppm per test | ≤ 2 % of reading or ≤ 75 ppm per test, whichever is larger
NOX | ≤ 5 ppm per test | ≤ 2 % of reading or ≤ 5 ppm per test, whichever is larger
CH4 | ≤ 10 ppm C1 per test | ≤ 2 % of reading or ≤ 10 ppm C1 per photos.
x |
22 | Check if less than 800 km away from next scheduled service, if yes, then perform the service. | | | x
23 | All checks requiring OBD connections to be performed before and/or after the end of testing | | |
24 | Powertrain Control Module calibration part number and checksum | | | x
25 |
OBD diagnosis (before or after the emissions test, whichever is larger
THC | ≤ 10 ppm C1 per test | ≤ 2 % of reading or ≤ 10 ppm C1 per )
Read Diagnostic Trouble Codes & Print error log
x
26 |
OBD Service Mode 09 Query (before or after the emissions test, whichever is larger
If the difference between the pre-test and post-test results for the zero and span drift is higher than permitted, all test results shall be voided and the test repeated.
The zero level of the analyser shall be recorded in accordance with point 4.6.
The calibrated range of the analysers shall account at least for 90 % of the concentration values obtained from 99 % of the measurements of the valid parts of the )
Read Service Mode 09. Record the information.
x
27 |
OBD mode 7 (before or after the emissions test. It is permissible that 1 % of the total number of measurements used for evaluation exceeds the calibrated range of the analysers by up to a factor of two. If these requirements are not met, the test shall be voided.)
Read Service Mode 07. Record the information
Remarks for: Repair / replacement of components / part numbers