22 Appendix 3, Regulation (EU) 2017/1151

In forcesince 1 Sep 2023

The following information shall be included in the detailed ISC report:

1.

Test Date

2.

Unique Number of ISC Report

3.

Date of approval by authorised representative

4.

Date of transmission to GTAA or upload to Electronic Platform

5.

the name and address of the manufacturer;

6.

the name, address, telephone and fax numbers and e-mail address of the responsible testing laboratory;

7.

the model name(s) of the vehicles included in the test plan;

8.

where appropriate, the list of vehicle types covered within the manufacturer's information, i.e. for tailpipe emissions, the in-service family;

9.

the numbers of the type approvals applicable to these vehicle types within the family, including, where applicable, the numbers of all extensions and field fixes/recalls (re-works);

10.

details of extensions, field fixes/recalls to those type approvals for the vehicles covered within the manufacturer's information (if requested by the approval authority);

11.

the period of time over which the information was collected;

12.

the ISC checking procedure, including where applicable:

(i)

vehicle sourcing method;

(ii)

vehicle selection and rejection criteria (including the answers to the table in Appendix 1, including photos);

(iii)

test types and procedures used for the programme;

(iv)

geographical area(s) within which the manufacturer has collected information;

(v)

sample lot number and sampling plan used;

13.

the results of the ISC procedure, including:

(i)

identification of the vehicles included in the programme (whether tested or not). The identification shall include the Table in Appendix 1 without the confidential items.

(ii)

test data for tailpipe emissions:

test fuel specifications (e.g. test reference fuel or market fuel),

test conditions (temperature, humidity, dynamometer inertia weight),

dynamometer settings (e.g. road load, power setting),

test results and calculation of pass/fail;

(iii)

test data for evaporative emissions:

test fuel specifications (e.g. test reference fuel or market fuel),

test conditions (temperature, humidity, dynamometer inertia weight),

dynamometer settings (e.g. road load, power setting),

test results and calculation of pass/fail.

Changed on 1 Sep 2023

This Appendix describes the test procedure to determine exhaust emissions from light passenger and commercial vehicles using a Portable Emissions Measurement System. ≤smaller or equal #number #/m3number per cubic metre %per cent °Cdegree centigrade ggramme g/sgramme per second hhour Hzhertz Kkelvin kgkilogramme kg/skilogramme per second kmkilometre km/hkilometre per hour kPakilopascal kPa/minkilopascal per minute llitre l/minlitre per minute mmetre m3cubic-metre mgmilligram minminute peevacuated pressure [kPa] qvsvolume flow rate of the system [l/min] ppmparts per million ppmC1parts per million carbon equivalent rpmrevolutions per minute ssecond Vssystem volume [l] The test The following information shall be carried out with a PEMS, composed of components specified in points 3.1.1 to 3.1.5. If applicable, a connection with the vehicle ECU may be established to determine relevant engine and vehicle parameters as specified in point 3.2. 3.1.1. Analysers to determine the concentration of pollutants in the exhaust gas. 3.1.2. One or multiple instruments or sensors to measure or determine the exhaust mass flow. 3.1.3. A Global Positioning System to determine the position, altitude and, speed of the vehicle. 3.1.4. If applicable, sensors and other appliances being not part of the vehicle, e.g., to measure ambient temperature, relative humidity, air pressure, and vehicle speed. 3.1.5. An energy source independent of the vehicle to power the PEMS. Test parameters as specified in Table 1 of this Appendix shall be measured at a constant frequency of 1,0 Hz or higher and recorded and reported in accordance with the requirements of Appendix 8 at a frequency of 1,0 Hz. If ECU parameters are available, these may be obtained at a substantially higher frequency but the recording rate shall be 1,0 Hz. The PEMS analysers, flow-measuring instruments and sensors shall comply with the requirements laid down in Appendices 2 and 3. [to be measured on a wet basis or to be corrected as described in point 8.1 of Appendix 4] [to be determined only if indirect methods are used to calculate exhaust mass flow rate as described in paragraphs 10.2 and 10.3 of Appendix 4] [method to be chosen according to point 4.7] [parameter only mandatory if measurement required by Annex IIIA, section 2.1] [to be determined only if necessary to verify the vehicle status and operating conditions] [may be calculated from THC and CH4 concentrations according to point 9.2 of Appendix 4] [may be calculated from measured NO and NO2 concentrations] [Multiple parameter sources may be used.] [The preferable source is the ambient pressure sensor.] Parameter | Recommended unit | Source THC concentration, | ppm C1 | Analyser CH4 concentration, | ppm C1 | Analyser NMHC concentration, | ppm C1 | Analyser CO concentration, | ppm | Analyser CO2 concentration | ppm | Analyser NOX concentration, | ppm | Analyser PN concentration | #/m3 | Analyser Exhaust mass flow rate | kg/s | EFM, any methods described in point 7 of Appendix 2 Ambient humidity | % | Sensor Ambient temperature | K | Sensor Ambient pressure | kPa | Sensor Vehicle speed | km/h | Sensor, GPS, or ECU Vehicle latitude | Degree | GPS Vehicle longitude | Degree | GPS Vehicle altitude, | M | GPS or Sensor Exhaust gas temperature | K | Sensor Engine coolant temperature | K | Sensor or ECU Engine speed | rpm | Sensor or ECU Engine torque | Nm | Sensor or ECU Torque at driven axle | Nm | Rim torque meter Pedal position | % | Sensor or ECU Engine fuel flow | g/s | Sensor or ECU Engine intake air flow | g/s | Sensor or ECU Fault status | — | ECU Intake air flow temperature | K | Sensor or ECU Regeneration status | — | ECU Engine oil temperature | K | Sensor or ECU Actual gear | # | ECU Desired gear (e.g. gear shift indicator) | # | ECU Other vehicle data | unspecified | ECU The preparation of the vehicle shall include a general verification of the correct technical functioning of the test vehicle. The installation of the PEMS shall follow the instructions of the PEMS manufacturer and the local health and safety regulations. The PEMS should be installed as to minimise during the test electromagnetic interferences as well as exposure to shocks, vibration, dust and variability in temperature. The installation and operation of the PEMS shall be leak-tight and minimise heat loss. The installation and operation of PEMS shall not change the nature of the exhaust gas nor unduly increase the length of the tailpipe. To avoid the generation of particles, connectors shall be thermally stable at the exhaust gas temperatures expected during the test. It is recommended not to use elastomer connectors to connect the vehicle exhaust outlet and the connecting tube. Elastomer connectors, if used, shall have no contact with the exhaust gas to avoid artefacts at high engine load. The installation and operation of the PEMS sampling probes shall not unduly increase the pressure at the exhaust outlet in a way that may influence the representativeness of the measurements. It is thus recommended that only one sampling probe is installed in the same plane. If technically feasible, any extension to facilitate the sampling or connection with the exhaust mass flow meter shall have an equivalent, or larger, cross sectional area than the exhaust pipe. Whenever used, the exhaust mass flow meter shall be attached to the vehicle's tailpipe(s) in accordance with the recommendations included in the detailed ISC report: 1. Test Date 2. Unique Number of ISC Report 3. Date of approval by authorised representative 4. Date of transmission to GTAA or upload to Electronic Platform 5. the name and address of the manufacturer; 6. the name, address, telephone and fax numbers and e-mail address of the responsible testing laboratory; 7. the model name(s) of the EFM manufacturer. The measurement range of the EFM shall match the range of the exhaust mass flow rate expected during the test. It is recommended to select the EFM in order to have the maximum expected flow rate during the vehicles included in the test covering at least 75 % of the EFM full range. The installation of the EFM and any exhaust pipe adaptors or junctions shall not adversely affect the operation of the engine or exhaust after-treatment system. A minimum of four pipe diameters or 150 mm of straight tubing, whichever is larger, shall be placed at either side of the flow-sensing element. When testing a multi-cylinder engine with a branched exhaust manifold, it is recommended to position the exhaust mass flow meter downstream of where the manifolds combine and to increase the cross section of the piping such as to have an equivalent, or larger, cross sectional area from which to sample. If this is not feasible, exhaust flow measurements with several exhaust mass flow meters may be used. The wide variety of exhaust pipe configurations, dimensions and exhaust mass flow rates may require compromises, guided by good engineering judgement, when selecting and installing the EFM(s). It is permissible to install an EFM with a diameter smaller than that of the exhaust outlet or the total projected frontal area of multiple outlets, providing it improves measurement accuracy and does not adversely affect the operation or the exhaust after-treatment as specified in point 3.4.2. It is recommended to document the EFM set-up using photographs. The GPS antenna should be mounted, e.g. at the highest possible location, as to ensure good reception plan; 8. where appropriate, the list of vehicle types covered within the manufacturer's information, i.e. for tailpipe emissions, the in-service family; 9. the numbers of the satellite signal. The mounted GPS antenna shall interfere as little as possible with the vehicle operation. If desired, relevant vehicle and engine parameters listed in Table 1 can be recorded by using a data logger connected with the ECU or the vehicle network through standards, such as ISO 15031-5 or SAE J1979, OBD-II, EOBD or WWH-OBD. If type approvals applicable, manufacturers shall disclose labels to allow the identification of required parameters. Vehicle speed sensors, temperature sensors, coolant thermocouples or any other measurement device not part of the to these vehicle shall be installed to measure the parameter under consideration in a representative, reliable and accurate manner without unduly interfering with the vehicle operation and the functioning of other analysers, flow-measuring instruments, sensors and signals. Sensors and auxiliary equipment shall be powered independently of the vehicle. It is permitted to power any safety-related illumination of fixtures and installations of PEMS components outside of the vehicle’s cabin by the vehicle’s battery. Emissions sampling shall be representative and conducted at locations of well-mixed exhaust types within the family, including, where the influence of ambient air downstream of the sampling point is minimal. If applicable, emissions shall be sampled downstream of the exhaust mass flow meter, respecting a distance of at least 150 mm to the flow sensing element. The sampling probes shall be fitted at least 200 mm or three times the inner diameter of the exhaust pipe, whichever is larger, upstream of the point at which the exhaust exits the PEMS sampling installation into the environment. If the PEMS feeds back a flow to the tail pipe, this shall occur downstream of the sampling probe in a manner that does not affect during engine operation the nature of the exhaust gas at the sampling point(s). If the length of the sampling line is changed, the system transport times shall be verified and if necessary corrected. If the engine is equipped with an exhaust after-treatment system, the exhaust sample shall be taken downstream of the exhaust after-treatment system. When testing a vehicle with a branched exhaust manifold, the inlet of the sampling probe shall be located sufficiently far downstream so as to ensure that the sample is representative of the average exhaust emissions of all cylinders. In multi-cylinder engines, having distinct groups of manifolds, such as in a ‘V’ engine configuration, the sampling probe shall be positioned downstream of where the manifolds combine. If this is technically not feasible, multi-point sampling at locations of well-mixed exhaust may be used, if approvedthe numbers of all extensions and field fixes/recalls (re-works); 10. details of extensions, field fixes/recalls to those type approvals for the vehicles covered within the manufacturer's information (if requested by the Type Approval Authority. In this case, the number and location of sampling probes shall match as far as possible those of the exhaust mass flow meters. In case of unequal exhaust flows, proportional sampling or sampling with multiple analysers shall be considered. If the engine is equipped with an exhaust after-treatment system, the exhaust sample shall be taken downstream of the exhaust after- treatment system. When testing a vehicle with a branched exhaust manifold, the inlet of the sampling probe shall be located sufficiently far downstream so as to ensure that the sample is representative of the average exhaust emissions of all cylinders. In multi-cylinder engines having distinct groups of manifolds, such as in a ‘V’ engine configuration, the sampling probe shall be positioned downstream of the point approval authority); 11. the period of time over which the information was collected; 12. the ISC checking procedure, including where the manifolds combine. If this is technically not feasible, multi-point sampling at locations of well-mixed exhaust may be used. In this case, the number and location of sampling probes shall match as far as possible those of the exhaust mass flow meters. In case of unequal exhaust flows, proportional sampling or sampling with multiple analysers shall be considered. If hydrocarbons are measured, the sampling line shall be heated to 463 ± 10 K (190 ± 10 °C). For the measurement of other gaseous components with or without cooler, the sampling line shall be kept at a minimum of 333 K (60 °C) to avoid condensation and to ensure appropriate penetration efficiencies of the various gases. For low pressure sampling systems, the temperature can be lowered corresponding to the pressure decrease provided that the sampling system ensures a penetration efficiency of 95 % for all regulated gaseous pollutants. If particles are sampled and not diluted at the tailpipe, the sampling line from the raw exhaust sample point to the point of dilution or particle detector shall be heated to a minimum of 373 K (100 °C). The residence time of the sample in the particle sampling line shall be less than 3 s until reaching first dilution or the particle detector. All parts of the sampling system from the exhaust pipe up applicable: (i) vehicle sourcing method; (ii) vehicle selection and rejection criteria (including the answers to the particle detector, which are in contact with raw or diluted exhaust gas, shall be designed to minimize deposition of particles. All parts shall be made from antistatic material to prevent electrostatic effects. After the installation of the PEMS is completed, a leak check shall be performed at least once for each PEMS-vehicle installation as prescribed by the PEMS manufacturer or as follows. The probe shall be disconnected from the exhaust system and the end plugged. The analyser pump shall be switched on. After an initial stabilization period all flow meters shall read approximately zero in the absence of a leak. Else, the sampling lines shall be checked and the fault be corrected. The leakage rate on the vacuum side shall not exceed 0.5 per cent of the in-use flow rate table in Appendix 1, including photos); (iii) test types and procedures used for the portion of the system being checked. The analyser flows and bypass flows may be used to estimate the in-use flow rate. Alternatively, the system may be evacuated to a pressure of at least 20 kPa vacuum (80 kPa absolute). After an initial stabilization period the pressure increase Δp (kPa/min) in the system shall not exceed: ΔppeVs qvs 0.005 Alternatively, a concentration step change at the beginning of the sampling line shall be introduced by switching from zero to span gas while maintaining the same pressure conditions as under normal system operation. If for a correctly calibrated analyser after an adequate period of time the reading is ≤ 99 per cent compared to the introduced concentration, the leakage problem shall be corrected. The PEMS shall be switched on, warmed up and stabilized in accordance with the specifications of the PEMS programme; (iv) geographical area(s) within which the manufacturer until key functional parameters, e.g., pressures, temperatures and flows have reached their operating set points before test start. To ensure correct functioning, the PEMS may be kept switched on or can be warmed up and stabilized during vehicle conditioning. The system shall be free of errors and critical warnings. The sampling system, consisting of the sampling probe has collected information; (v) sample lot number and sampling lines shall be prepared for testing by following the instruction of the PEMS manufacturer. It shall be ensured that the sampling system is clean and free of moisture condensation. If used for measuring the exhaust mass flow, the EFM shall be purged and prepared for operation in accordance with the specifications of the EFM manufacturer. This plan used; 13. the results of the ISC procedure shall, if applicable, remove condensation and deposits from the lines and the associated measurement ports. Zero and span calibration adjustments , including: (i) identification of the analysers shall be performed using calibration gases that meet the requirements of point 5 of Appendix 2vehicles included in the programme (whether tested or not). The calibration gases identification shall be chosen to match the range of pollutant concentrations expected during the RDE test. To minimize analyser drift, one should conduct the zero and span calibration of analysers at an ambient temperature that resembles, as closely as possible, the temperature experienced by the test equipment during the trip. The zero level of the analyser shall be recorded by sampling HEPA filtered ambient air at an appropriate sampling point, usually at the inlet of the sampling line. The signal shall be recorded at a constant frequency which is a multiple of 1,0 Hz averaged over a period of 2 minutes; the final concentration shall be within the manufacturer's specifications, but shall not exceed 5000 particles per cubic-centimetre. Vehicle speed shall be determined by at least one of the following methods: (a) a GPS; if vehicle speed is determined by a GPS, the total trip distance shall be checked against the measurements of another method according to point 7 of Appendix 4. (b) a sensorinclude the Table in Appendix 1 without the confidential items. (ii) test data for tailpipe emissions: test fuel specifications (e.g., optical or micro-wave sensor); if vehicle speed is determined by a sensor, the speed measurements shall comply with the requirements of point 8 of Appendix 2, or alternatively, the total trip distance determined by the sensor shall be compared with a test reference distance obtained from a digital road network or topographic map. The total trip distance determined by the sensor shall deviate by no more than 4 % from the reference distance. (c) the ECU; if vehicle speed is determined by the ECU, the total trip distance shall be validated according to point 3 of Appendix 3 and the ECU speed signal adjusted, if necessary to fulfil the requirements of point 3.3 of Appendix 3. Alternatively, the total trip distance as determined by the ECU can be compared with a reference distance obtained from a digital road network or topographic map. The total trip distance determined by the ECU shall deviate by no more than 4 % from the reference. The correctness of connections with all sensors and, if applicable, the ECU shall be verified. If engine parameters are retrieved, it shall be ensured that the ECU reports values correctly fuel or market fuel), test conditions (temperature, humidity, dynamometer inertia weight), dynamometer settings (e.g., zero engine speed [rpm] while the combustion engine is in key-on-engine-off status). The PEMS shall function free of errors and critical warnings. Test start (see Figure App.1.1) shall be defined by either: the first ignition of the internal combustion engine; or the first movement of the vehicle with speed greater than 1 km/h for OVC-HEVs and NOVC-HEVS starting with the internal combustion engine off. Sampling, measurement and recording of parameters shall begin prior to the test start. Before the test start it shall be confirmed that all necessary parameters are recorded by the data logger. To facilitate time alignment, it is recommended to record the parameters that are subject to time alignment either by a single data recording device or with a synchronised time stamp. Sampling, measurement and recording of parameters shall continue throughout the on-road road load, power setting), test of the vehicle. The engine may be stopped and started, but emissions sampling and parameter recording shall continue. Any warning signals, suggesting malfunctioning of the PEMS, shall be documented and verified. If any error signal(s) appear during the results and calculation of pass/fail; (iii) test, the test shall be voided. Parameter recording shall reach a data completeness of higher than 99 %. Measurement and data recording may be interrupted for less than 1 % of the total trip duration but for no more than a consecutive period of 30 s solely in the case of unintended signal loss or for the purpose of PEMS system maintenance. Interruptions may be recorded directly by the PEMS but it is not permissible to introduce interruptions in the recorded parameter via the pre-processing, exchange or post-processing of data. If conducted, auto zeroing shall be performed against a traceable zero standard similar to the one used to zero the analyser. It is strongly recommended to initiate PEMS system maintenance during periods of zero vehicle speed. The end of the for evaporative emissions: test (see Figure App.1.2) is reached when the vehicle has completed the trip and either when: the internal combustion engine is switched off; or: for OVC-HEVs and NOVC-HEVS finishing the fuel specifications (e.g. test with the internal combustion engine off, the vehicle stops and the speed is lower than or equal to 1 km/h. Excessive idling of the engine after the completion of the trip shall be avoided. The data recording shall continue until the response time of the sampling systems has elapsed. For vehicles with a signal detecting regeneration (see line 42 in the Transparency List 1 in Appendix 5 of Annex II), the OBD-check shall be performed and documented directly after data recording and before any further driven distance is driven. The zero and span of the analysers of gaseous components shall be checked by using calibration gases identical to the ones applied under point 4.5 to evaluate the analyser's zero and response drift compared to the pre-reference fuel or market fuel), test calibration. It is permissible to zero the analyser prior to verifying the span drift, if the zero drift was determined to be within the permissible range. The post-test drift check shall be completed as soon as possible after the test and before the PEMS, or individual analysers or sensors, are turned off or have switched into a non-operating mode. The difference between the pre-test and post-test results shall comply with the requirements specified in Table 2. [If the zero drift is within the permissible range, it is permissible to zero the analyser prior to verifying the span drift.] Pollutant | Absolute Zero response drift | Absolute Span response drift CO2 | ≤ 2000 ppm per test | ≤ 2 % of reading or ≤ 2000 ppm per test, whichever is larger CO | ≤ 75 ppm per conditions (temperature, humidity, dynamometer inertia weight), dynamometer settings (e.g. road load, power setting), test | ≤ 2 % of reading or ≤ 75 ppm per test, whichever is larger NOX | ≤ 5 ppm per test | ≤ 2 % of reading or ≤ 5 ppm per test, whichever is larger CH4 | ≤ 10 ppm C1 per test | ≤ 2 % of reading or ≤ 10 ppm C1 per test, whichever is larger THC | ≤ 10 ppm C1 per test | ≤ 2 % of reading or ≤ 10 ppm C1 per test, whichever is larger If the difference between the pre-test and post-test results for the zero and span drift is higher than permitted, all test results shall be voided and the test repeated. The zero level of the analyser shall be recorded in accordance with point 4.6. The span gas concentration that was used for the calibration of the analysers in accordance with paragraph 4.5 at the test start shall cover at least 90 % of the concentration values obtained from 99 % of the measurement of the valid parts of the emissions test. It is permissible that 1 % of the total number of measurements used for evaluation exceeds the used span gas by up to a factor of two. If these requirements are not met, the test shall be voided.and calculation of pass/fail.

  1. 1 Sep 2023 – todayin force
  2. 1 Jan 2019 – 1 Sep 2023earlier wording
  3. 27 Jul 2017 – 1 Jan 2019earlier wording
  4. 1 Jun 2017 – 27 Jul 2017earlier wording