37 Appendix 11, Regulation (EU) 2017/1151

In forcesince 1 Sep 2023

Index (k) refers to the category (t=total, u=urban, 1-2=first two phases of the WLTP test)

ICk | is the distance share of usage of the internal combustion engine for an OVC-HEV over the RDE trip

dICE,k | is the distance driven [km], with the internal combustion engine on for an OVC-HEV over the RDE trip

dEV,k | is the distance driven [km], with the internal combustion engine off for an OVC-HEV over the RDE trip

MRDE,k | is the final RDE distance-specific mass of gaseous pollutants [mg/km] or particle number [#/km]

mRDE,k | is the distance-specific mass of gaseous pollutant [mg/km] or particle number [#/km] emissions, emitted over the complete RDE trip and prior to any correction in accordance with this appendix

MCO2,RDE,k | is the distance-specific mass of CO2 [g/km], emitted over the RDE trip

MCO2,WLTC,k | is the distance-specific mass of CO2 [g/km], emitted over the WLTC cycle

MCO2,WLTC_CS,k | is the distance-specific mass of CO2 [g/km], emitted over the WLTC cycle for an OVC-HEV vehicle tested in charge sustaining vehicle operation

rk | is the ratio between the CO2 emissions measured during the RDE test and the WLTP test

RFk | is the result evaluation factor calculated for the RDE trip

RFL1 | is the first parameter of the function used to calculate the result evaluation factor

RFL2 | is the second parameter of the function used to calculate the result evaluation factor

For the valid trips, the intermediate RDE results are calculated as follows for vehicles with ICE, NOVC-HEV and OVC-HEV.

Any instantaneous emissions or exhaust flow measurements obtained while the combustion engine is deactivated, as defined in paragraph 2.5.2. of this Annex, shall be set to zero.

Any correction of the instantaneous pollutant emissions for Extended conditions according to paragraph 5.1., 7.5. and 7.6. of this Annex shall be applied.

For the complete RDE trip and for the urban part of the RDE trip (k=t=total, k=u=urban):

MRDE,k mRDE,k RFk

The values of the parameter RFL1 and RFL2 of the function used to calculate the result evaluation factor are as follows:

RFL1=1.30 and RFL2=1.50;

The RDE result evaluation factors RFk (k=t=total, k=u=urban) shall be obtained using the functions laid down in paragraph 3.1. for vehicles with ICE and NOVC-HEV, and in paragraph 3.2. for OVC-HEV. A graphical illustration of the method is provided in Figure A11/1 below, while the mathematical formulas are found in Table A11/1:

When: | Then the Result evaluation factor RFk is: | Where:

rk RFL1 | RFk 1 |

RFL1 rk RFL2 | RFk a1rk b1 |

a1RFL2 1

RFL2 RFL1 RFL2

b1 1 a1RFL1

rk RFL2 | RFk1rk |

The value of the RDE result evaluation factor depends on the ratio rk between the distance specific CO2 emissions measured during the RDE test and the distance-specific CO2 emitted by the vehicle over the validation WLTP test conducted on this vehicle including all appropriate corrections.

For the urban emissions, the relevant phases of the WLTP test shall be:

(a)

for ICE vehicles, the first two WLTC phases, i.e. the Low and the Medium speed phases,

rkMCO2,RDE,kMCO2,WLTP,k

(b)

for NOVC-HEVs, all the phases of the WLTC driving cycle.

rkMCO2,RDE,kMCO2,WLTP,t

The value of the RDE result evaluation factor depends on the ratio rk between the distance-specific CO2 emissions measured during the RDE test and the distance-specific CO2 emitted by the vehicle over the applicable WLTP test conducted in Charge Sustaining vehicle operation including all appropriate corrections. The ratio rk is corrected by a ratio reflecting the respective usage of the internal combustion engine during the RDE trip and on the WLTP test, to be conducted in charge sustaining vehicle operation.

For either the urban or the total driving:

rkMCO2,RDE,kMCO2,WLTP_CS,t0,85ICk

where ICk is the ratio of the distance driven either in urban or total trip with the combustion engine activated, divided by the total urban or total trip distance:

ICkdICE,kdICE,k dEV,k

With determination of combustion engine operation in accordance with paragraph 2.5.2. of this Annex.

In order to take into account the uncertainty of the PEMS measurements compared to the ones performed in the laboratory with the applicable WLTP test, the intermediate calculated emission values MRDE,k shall be divided by 1+marginpollutant., where marginpollutant is defined in the Table A11/2:

The PEMS margin for each pollutant is specified as follows:

Pollutant | Mass of oxides of nitrogen (NOx) | Number of particles (PN) | Mass of carbon monoxide (CO) | Mass of total hydrocarbons (THC) | Combined mass of total hydrocarbons and oxides of nitrogen (THC + NOx)

Marginpollutant | 0,10 | 0,34 | Not yet specified | Not yet specified | Not yet specified

Any negative final results shall be set to zero.

Any Ki factors which are applicable, according to point 5.3.4. of this Annex, shall be applied.

These values shall be considered the Final RDE Emission Results for NOx and PN.