34 Appendix 8, Regulation (EU) 2017/1151

In forcesince 1 Sep 2023

The Moving Averaging Window method shall be used to assess the overall trip dynamics. The test is divided in sub-sections (windows) and the subsequent analysis aims at determining whether the trip is valid for RDE purposes. The ‘normality’ of the windows shall be assessed by comparing their CO2 distance-specific emissions with a reference curve obtained from the vehicle CO2 emissions measured in accordance with the WLTP test.

Index (i) refers to the time step

Index (j) refers to the window

Index (k) refers to the category (t=total, ls=low speed, ms=medium speed, hs=high speed) or to the CO2 characteristic curve (cc)

a1,b1coefficients of the CO2 characteristic curve

a2,b2coefficients of the CO2 characteristic curve

MCO2CO2 mass, [g]

MCO2jCO2 mass in window j, [g]

titotal time in step i, [s]

ttduration of a test, [s]

viactual vehicle speed in time step i, [km/h]

v

javerage vehicle speed in window j, [km/h]

tol1Hupper tolerance for the vehicle CO2 characteristic curve, [%]

tol1Llower tolerance for the vehicle CO2 characteristic curve, [%]

The instantaneous CO2 emissions calculated according to Appendix 7 shall be integrated using a moving averaging window method, based on a reference CO2 mass.

The usage of the reference CO2 mass is illustrated in Figure A8/2. The principle of the calculation is as follows: The RDE distance-specific CO2 mass emissions are not calculated for the complete data set, but for sub-sets of the complete data set, the length of these sub-sets being determined so as to match always the same fraction of the CO2 mass emitted by the vehicle over the applicable WLTP test (after all appropriate corrections e.g. ATCT are applied, where relevant). The moving window calculations are conducted with a time increment Δt corresponding to the data sampling frequency. These sub-sets used to calculate the vehicle on-road CO2 emissions and its average speed are referred to as ‘averaging windows’ in the following sections. The calculation described in this point shall be run from the first data point (forward), as shown in Figure A8/1.

The following data shall not be considered for the calculation of the CO2 mass, the distance and the vehicle average speed in each averaging window:

The periodic verification of the instruments and/or after the zero drift verifications;

Vehicle ground speed < 1 km/h;

The calculation shall start from when vehicle ground speed is higher than or equal to 1 km/h and include driving events during which no CO2 is emitted and where the vehicle ground speed is higher than or equal to 1 km/h.

The mass emissions MCO2,j shall be determined by integrating the instantaneous emissions in g/s as specified in Appendix 7.

The duration (t2,j – t1,j) of the jth averaging window is determined by:

MCO2 (t2,j) – MCO2 (t1,j) ≥ MCO2,ref

Where:

MCO2(ti,j) is the CO2 mass measured between the test start and time ti,j, [g];

MCO2,ref is the reference CO2 mass (half of the CO2 mass emitted by the vehicle over the applicable WLTP test).

During type approval, the CO2 reference value shall be taken from the WLTP test CO2 values of the individual vehicle, obtained in accordance with UN Regulation 154, including all appropriate corrections.

For ISC or market surveillance testing purposes, the reference CO2 mass shall be obtained from the Certificate of Conformity [As found in Annex VIII of Regulation (EU) 2020/638.] for the individual vehicle. The value for OVC-HEV vehicles shall be obtained from the WLTP test conducted using the Charge Sustaining mode.

t2,j shall be selected such as:

MCO2 (t2,j – Δt) – MCO2 (t1,j) < MCO2,ref ≤ MCO2 (t2,j) – MCO2 (t1,j)

Where Δt is the data sampling period.

The CO2 masses MCO2,j in the windows are calculated by integrating the instantaneous emissions calculated as specified in Appendix 7.

The following shall be calculated for each window determined in accordance with paragraph 3.1. The distance-specific CO2 emissions MCO2,d,j;

The average vehicle speed

v

j

The reference dynamic conditions of the test vehicle are defined from the vehicle CO2 emissions versus average speed measured at type approval on the WLTP test and referred to as ‘vehicle CO2 characteristic curve’.

4.2.

CO2 characteristic curve reference points

During type approval, the values shall be taken from the WLTP CO2 values of the individual vehicle, obtained in accordance with UN Regulation 154, including all appropriate corrections.

For ISC or market surveillance testing purposes, the distance-specific CO2 emissions to be considered, in this paragraph for the definition of the reference curve shall be obtained from the Certificate of Conformity for the individual vehicle.

The reference points P1, P2 and P3 required to define the vehicle CO2 characteristic curve shall be established as follows:

4.2.1. Point P1

vP1

= 18,882 km/h (Average Speed of the Low Speed phase of the WLTP cycle)

MCO2,d,P1 = Vehicle CO2 emissions over the Low Speed phase of the WLTP test [g/km]

4.2.2. Point P2

vP2

= 56,664 km/h (Average Speed of the High Speed phase of the WLTP cycle)

MCO2,d,P2 = Vehicle CO2 emissions over the High Speed phase of the WLTP test [g/km]

4.2.3. Point P3

vP3

= 91,997 km/h(Average Speed of the Extra High Speed phase of the WLTP cycle)

MCO2,d,P3= Vehicle CO2 emissions over the Extra High Speed phase of the WLTP test [g/km]

Using the reference points defined in paragraph 4.2., the characteristic curve CO2 emissions are calculated as a function of the average speed using two linear sections (P1, P2) and (P2, P3). The section (P2, P3) is limited to 145 km/h on the vehicle speed axis. The characteristic curve is defined by equations as follows:

For the section (P1,P2):

MCO2,d,CC

v

a1

v

b1

with: a1MCO2,d,P2 MCO2,d,P1

vP2

vP1

and: b1MCO2,d,P1 a1

vP1

For the section (P2,P3):

MCO2,d,CC

v

a2

v

b2

with: a2MCO2,d,P3 MCO2,d,P2

vP3

vP2

and: b2MCO2,d,P2 a2

vP2

4.4.1. The windows shall be categorised into low, medium, and high speed bins according to their average speed.

4.4.1.1. Low-speed windows

Low-speed windows are characterized by average vehicle ground speeds

v

j lower than 45 km/h.

4.4.1.2. Medium-speed windows

Medium-speed windows are characterized by average vehicle ground speeds

v

j greater than or equal to 45 km/h and lower than 80 km/h.

For those vehicles that are equipped with a device limiting vehicle speed to 90 km/h, medium-speed windows are characterized by average vehicle speeds

v

j lower than 70 km/h.

4.4.1.3. High-speed windows

High-speed windows are characterized by average vehicle ground speeds

v

j greater than or equal to 80 km/h and lower than 145 km/h

For those vehicles that are equipped with a device limiting vehicle speed to 90 km/h, high-speed windows are characterized by average vehicle speeds

v

j greater than or equal to 70 km/h and lower than 90 km/h.

4.5.1. Assessment of trip validity

4.5.1.1. Tolerances around the vehicle CO2 characteristic curve

The upper tolerance of the vehicle CO2 characteristic curve is tol1H = 45 % for low speed driving and tol1H = 40 % for medium and high speed driving.

The lower tolerance of the vehicle CO2 characteristic curve is tol1L = 25 % for ICE and NOVC-HEV vehicles and tol1L = 100 % for OVC-HEV vehicles.

4.5.1.2. Assessment of test validity

The test is valid when it comprises at least 50 per cent of the low, medium and high speed windows that are within the tolerances defined for the CO2 characteristic curve.

For NOVC-HEVs and OVC-HEVs, if the minimum requirement of 50 % between tol1H and tol1L is not met, the upper positive tolerance tol1H may be increased until the value of tol1H reaches 50 per cent.

For OVC-HEVs when no MAWs are calculated as result of the ICE not turning on, the test is still valid.

  • celex=32020R0638