Section 3 of the EC type-approval number issued according to Article 6(1) The information required in this Appendix shall be composedprovided by the number of the implementing regulatory act or the latest amending regulatory act applicable to the EC type-approval. This number shall be followed by one or more characters reflecting the different categories in accordance with Table 1.
[This limitation does not apply if a vehicle was type-approved in accordance with the requirements of Regulation (EC) No 715/2007 and its implementing legislation prior to 1 September 2017 in the case of category M and N1 class I vehicles, or prior to 1 September 2018 in the case of category N1 class II and III and category N2 vehicles, according to the last subparagraph of Article 15(4).]
‘Euro 6-1’ OBD standardFull Euro 6 OBD requirements but with preliminary OBD threshold limits as defined in point 2.3.4 of Annex XI and partially relaxed IUPR;
‘Euro 6-2’ OBD standardFull Euro 6 OBD requirements but with final OBD threshold limits as defined in point vehicle manufacturer for the purposes of enabling the manufacture of OBD-compatible replacement or service parts and diagnostic tools and test equipment.
2.
Upon request, the following information shall be made available to any interested component, diagnostic tools or test equipment manufacturer, on a non-discriminatory basis:
2.1. A description of the type and number of the preconditioning cycles used for the original type-approval of the vehicle;
2.2. A description of the type of the OBD demonstration cycle used for the original type-approval of the vehicle for the component monitored by the OBD system;
2.3.3 of Annex XI;
‘Euro 6b’ emissions standardEuro 6 emission requirements including revised measurement procedure for particulate matter, particle A comprehensive document describing all sensed components with the strategy for fault detection and MI activation (fixed number standards (preliminary values for PI direct injection);
‘Euro 6c’ emissions standardRDE NOx testing for monitoring only (no NTE emission limits applied), otherwise full Euro 6 tailpipe emission requirements (including PN RDE);
‘Euro 6c-EVAP’ emissions standardRDE NOx testing for monitoring only (no NTE emission limits applied), otherwise full Euro 6 tailpipe of driving cycles or statistical method), including a list of relevant secondary sensed parameters for each component monitored by the OBD system and a list of all OBD output codes and format used (with an explanation of each) associated with individual emission requirements (including PN RDE), revised evaporative emissions test procedure;
‘Euro 6d-TEMP’ emissions standardRDE NOx testing against temporary conformity factors, otherwise full Euro 6 tailpipe emission requirements (including PN RDE);
‘Euro 6d-TEMP-EVAP’ emissions standardRDE NOx testing against temporary conformity factors, otherwise full Euro 6 tailpipe emission requirements (including PN RDE), revised evaporative emissions test procedure;
‘Euro 6d’ emissions standardRDE testing against final conformity factors, otherwise full Euro 6 tailpipe emission requirements, revised evaporative emissions test procedure.
Character | Emission standard | OBD standard | Vehicle category and class | Engine | Implementation date: new types | Implementation date: new vehicles | Last date of registration
AA | Euro 6c | Euro 6-1 | M, N1 class I | PI, CI | | | 31.8.2018
BA | Euro 6b | Euro 6-1 | M, N1 class I | PI, CI | | | 31.8.2018
AB | Euro 6c | Euro 6-1 | N1 class II | PI, CI | | | 31.8.2019
BB | Euro 6b | Euro 6-1 | N1 class II | PI, CI | | | 31.8.2019
AC | Euro 6c | Euro 6-1 | N1 class III, N2 | PI, CI | | | 31.8.2019
BC | Euro 6b | Euro 6-1 | N1 class III, N2 | PI, CI | | | 31.8.2019
AD | Euro 6c | Euro 6-2 | M, N1 class I | PI, CI | | 1.9.2018 | 31.8.2019
AE | Euro 6c-EVAP | Euro 6-2 | N1 class II | PI, CI | | 1.9.2019 | 31.8.2020
AF | Euro 6c-EVAP | Euro 6-2 | N1 class III, N2 | PI, CI | | 1.9.2019 | 31.8.2020
AG | Euro 6d-TEMP | Euro 6-2 | M, N1 class I | PI, CI | 1.9.2017 | | 31.8.2019
BG | Euro 6d-TEMP-EVAP | Euro 6-2 | M, N1 class I | PI, CI | 1.9.2019 | 1.9.2019 | 31.12.2020
AH | Euro 6d-TEMP | Euro 6-2 | N1 class II | PI, CI | 1.9.2018 | | 31.8.2019
BH | Euro 6d-TEMP-EVAP | Euro 6-2 | N1 class II | PI, CI | 1.9.2019 | 1.9.2020 | 31.12.2021
AI | Euro 6d-TEMP | Euro 6-2 | N1 class III, N2 | PI, CI | 1.9.2018 | | 31.8.2019
BI | Euro 6d-TEMP-EVAP | Euro 6-2 | N1 class III, N2 | PI, CI | 1.9.2019 | 1.9.2020 | 31.12.2021
AJ | Euro 6d | Euro 6-2 | M, N1 class I | PI, CI | 1.1.2020 | 1.1.2021 |
AK | Euro 6d | Euro 6-2 | N1 class II | PI, CI | 1.1.2021 | 1.1.2022 |
AL | Euro 6d | Euro 6-2 | N1 class III, N2 | PI, CI | 1.1.2021 | 1.1.2022 |
AX | n.a. | n.a. | All vehicles | Battery full electric | | |
AY | n.a. | n.a. | All vehicles | Fuel cell | | |
AZ | n.a. | n.a. | All vehicles using certificates according to point 2.1.1 of Annex I | PI, CI | | |
2.1 An example is provided below of an approval of a Euro 6 light passenger car to the 'Euro 6d' emission standard and 'Euro 6-2' OBD standard, identified by the characters AJ according to table 1, issued by Luxembourg, identified by the code e13. The approval was granted for the base Regulation (EC) 715/2007 and its implementing Regulation (EC) xxx/2016 without any amendments. It is the 17th approval of this kind without any extension, so the fourth and fifth components of the certification number are 0017 and 00, respectively.
e13 7152007 xxx2016AJ 0017 00
2.2 This second example shows an approval of a Euro 6 N1 class II light commercial vehicle to the 'Euro 6d-TEMP' emission standard and 'Euro 6-2' OBD standard, identified by the characters AH according to table 1, issued by Romania, identified by the code e19. The approval was granted for the base Regulation (EC) 715/2007 and its implementing legislation as last amended by a Regulation xyz/2018. It is the 1st approval of this kind without extension, so the fourth and fifth components of the certification number are 0001 and 00, respectively.
e19 7152007 xyz2018AH 0001 00-related power-train components and individual non-emission related components, where monitoring of the component is used to determine MI activation. In particular, a comprehensive explanation for the data given in service $ 05 Test ID $ 21 to FF and the data given in service $ 06 shall be provided. In the case of vehicle types that use a communication link in accordance with ISO 15765-4 ‘Road vehicles — Diagnostics on Controller Area Network (CAN) — Part 4: Requirements for emissions-related systems’, a comprehensive explanation for the data given in service $ 06 Test ID $ 00 to FF, for each OBD monitor ID supported, shall be provided.
This information may be provided in the form of a table, as follows:
Component | Fault code | Monitoring strategy | Fault detection criteria | MI activation criteria | Secondary parameters | Preconditioning | Demonstration test
Catalyst | P0420 | Oxygen sensor 1 and 2 signals | Difference between sensor 1 and sensor 2 signals | 3rd cycle | Engine speed, engine load, A/F mode, catalyst temperature | e.g. Two Type 1 cycles (as described in Annex III of Regulation (EC) No 692/2008 or in Annex XXI to Regulation (EU) 2017/1151) | e.g. Type 1 test (as described in Annex III of Regulation (EC) No 692/2008 or in Annex XXI to Regulation (EU) 2017/1151)
In order to facilitate the provision of generic diagnostic tools for multi-make repairers, vehicle manufacturers shall make available the information referred to in the points 3.1 to 3.3. through their repair information web-sites. This information shall include all diagnostic tool functions and all the links to repair information and troubleshooting instructions. The access to this information may be subject to the payment of a reasonable fee.
The following information shall be required indexed against vehicle make, model and variant, or other workable definition such as VIN or vehicle and systems identification:
(a) Any additional protocol information system necessary to enable complete diagnostics in addition to the standards prescribed in Section 4 of Annex XI, including any additional hardware or software protocol information, parameter identification, transfer functions, ‘keep alive’ requirements, or error conditions;
(b) Details of how to obtain and interpret all fault codes not in accordance with the standards prescribed in Section 4 of Annex XI:
(c) A list of all available live data parameters including scaling and access information;
(d) A list of all available functional tests including device activation or control and the means to implement them;
(e) Details of how to obtain all component and status information, time stamps, pending DTC and freeze frames;
(f) Resetting adaptive learning parameters, variant coding and replacement component setup, and customer preferences;
(g) ECU identification and variant coding;
(h) Details of how to reset service lights;
(i) Location of diagnostic connector and connector details;
(j) Engine code identification.
The following information shall be required:
(a) A description of tests to confirm its functionality, at the component or in the harness
(b) Test procedure including test parameters and component information
(c) Connection details including minimum and maximum input and output and driving and loading values
(d) Values expected under certain driving conditions including idling
(e) Electrical values for the component in its static and dynamic states
(f) Failure mode values for each of the above scenarios
(g) Failure mode diagnostic sequences including fault trees and guided diagnostics elimination.
The following information shall be required:
(a) ECU and component initialisation (in the event of replacements being fitted)
(b) Initialisation of new or replacement ECUs where relevant using pass-through (re-) programming techniques.