15 Appendix 8a, Regulation (EU) 2017/1151

In forcesince 1 Sep 2023

A Test Report is the report issued by the technical service responsible for conducting the tests according this regulation.

The following information, if applicable, is the minimum data required for the Type 1 test.

APPLICANT | | |

Manufacturer | | |

SUBJECT | …

Roadload family identifier(s) | : |

Interpolation family identifier(s) | : |

Object submitted to tests

Make | : |

IP identifier | : |

CONCLUSION | The object submitted to tests complies with the requirements mentioned in the subject.

PLACE, | DD/MM/YYYY

If there are several options (references), the one tested should be described in the test report

If there are not, a single reference to the information document at the start of the test report may be sufficient.

Every Technical Service is free to include some additional information

Characters are included in the sections of the test report relating to specific vehicle types, as follows:

‘(a)’ Specific to positive ignition engine vehicles.

‘(b)’ Specific to compression ignition engine vehicles.

Vehicle numbers | : | Prototype number and VIN

Category | : |

Bodywork | : |

Drive wheels | : |

Powertrain architecture | : | pure ICE, hybrid, electric or fuel cell

For more than one ICE, please repeat the point

[a tolerance of +/– 10 per cent is permitted for volume and weight]

Make | : | | | | | |

Type | : | | | | | |

Working principle | : | two/four stroke

Cylinders number and arrangement | : | | | | | |

Engine capacity (cm3) | : | | | | | |

Engine idling speed (min–1) | : | | | +

High engine idling speed (min–1) (a) | : | | | +

Rated engine power | : | | kW | at | | rpm

Maximum net torque | : | | Nm | at | | rpm

Engine lubricant | : | make and type

Cooling system | : | Type: air/water/oil

Insulation | : | material, amount, location, nominal volume and nominal weight

For more than one test fuel, please repeat the point

Make | : |

Type | : | Petrol E10 - Diesel B7 – LPG – NG - …

Density at 15 °C | : |

Sulphur content | : | Only for Diesel B7 and Petrol E10

Batch number | : |

Willans factors (for ICE) for CO2 emission (gCO2/MJ) | : |

For more than one fuel feed system, please repeat the point

Direct injection | : | yes/no or description

Vehicle fuel type | : | Monofuel / bifuel / flex fuel

Control unit | : |

Part reference | : | same as information document

Software tested | : | read via scantool, for example

Air flowmeter | : |

Throttle body | : |

Pressure sensor | : |

Injection pump | : |

Injector(s) | : |

For more than one intake system, please repeat the point

Pressure charger | : |

Yes/no

make & type (1)

Intercooler | : |

yes/no

type (air/air – air/water) (1)

Air filter (element) (1) | : | make & type

Intake silencer (1) | : | make & type

For more than one, please repeat the point

First catalytic converter | : |

make & reference (1)

principle: three way / oxidising / NOx trap / NOx storage system / Selective Catalyst Reduction…

Second catalytic converter | : |

make & reference (1)

principle: three way/oxidising / NOx trap / NOx storage system / Selective Catalyst Reduction…

Particulate trap | : |

with/without/not applicable

catalysed: yes/no

make & reference (1)

Reference and position of oxygen sensor(s) | : | before catalyst/after catalyst

Air injection | : | with/without/not applicable

Water injection | : | with/without/not applicable

EGR | : |

with/without/not applicable

cooled/non-cooled

HP/LP

Evaporative emission control system | : | with/without/not applicable

Reference and position of NOx sensor(s) | : | Before/after

General description (1) | : |

For more than one Heat Storage System, please repeat the point

Heat storage device | : | yes/no

Heat capacity (enthalpy stored J) | : |

Time for heat release (s) | : |

For more than one Transmission, please repeat the point

[For OVC-HEV, specify for charge-sustaining and for charge-depleting operating conditions.]

Gearbox | : | manual / automatic / continuous variation

Gear shifting procedure

Predominant mode | : |

yes/no

normal / drive / eco/…

Best case mode for CO2 emissions and fuel consumption (if applicable) | : |

Worst case mode for CO2 emissions and fuel consumption (if applicable) | : |

Highest electric energy consumption mode (if applicable) | : |

Control unit | : |

Gearbox lubricant | : | make and type

Tyres

Make | : |

Type | : |

Dimensions front/rear | : |

Dynamic circumference (m) | : |

Tyre pressure (kPa) | : |

Transmission ratios (R.T.), primary ratios (R.P.) and (vehicle speed (km/h)) / (engine speed (1000 (min–1)) (V1000) for each of the gearbox ratios (R.B.).

R.B. | R.P. | R.T. | V1000

1st | 1/1 | |

2nd | 1/1 | |

3rd | 1/1 | |

4th | 1/1 | |

5th | 1/1 | |

… | | |

For more than one Electric Machine, please repeat the point

Make | : |

Type | : |

Peak Power (kW) | : |

For more than one Traction REESS, please repeat the point

Make | : |

Type | : |

Capacity (Ah) | : |

Nominal Voltage (V) | : |

For more than one Fuel Cell, please repeat the point

Make | : |

Type | : |

Maximum Power (kW) | : |

Nominal Voltage (V) | : |

Can be more than one PE (propulsion converter, low voltage system or charger)

Make | : |

Type | : |

Power (kW) | : |

Test mass of VH (kg) | : |

f0 (N) | : |

f1 (N/(km/h)) | : |

f2 (N/(km/h)2) | : |

Cycle energy demand (J) | : |

Road load test report reference | : |

Road load family's identifier | : |

Cycle (without downscaling) | : | Class 1 / 2 / 3a / 3b

Ratio of rated power to mass in running order (PMR)(W/kg) | : | (if applicable)

Capped speed process used during measurement | : | yes/no

Maximum speed of the vehicle (km/h) | : |

Downscaling (if applicable) | : | yes/no

Downscaling factor fdsc | : |

Cycle distance (m) | : |

Constant speed (in the case of the shortened test procedure) | : | if applicable

Version of Gear Shift calculation | | (indicate the applicable amendment to Regulation (EU) 2017/1151)

Gear shifting | : | Average gear for v ≥ 1 km/h, x.xxxx

nmin drive

1st gear | : | …min–1

1st gear to 2nd | : | …min–1

2nd gear to standstill | : | …min–1

2nd gear | : | …min–1

3rd gear and beyond | : | …min–1

Gear 1 excluded | : | yes/no

n_95_high for each gear | : | …min–1

n_min_drive_set for acceleration/constant speed phases (n_min_drive_up) | : | …min–1

n_min_drive_set for deceleration phases (nmin_drive_down) | : | …min–1

t_start_phase | : | …s

n_min_drive_start | : | …min–1

n_min_drive_up_start | : | …min–1

use of ASM | : | yes/no

ASM values | : |

Test mass of VL(kg) | : |

f0 (N) | : |

f1 (N/(km/h)) | : |

f2 (N/(km/h)2) | : |

Cycle energy demand (J) | : |

Δ(CD × Af)LH (m2) | : |

Road load test report reference | : |

Road load family's identifier | : |

Cycle (without downscaling) | : | Class 1 / 2 / 3a / 3b

Ratio of rated power to mass in running order – 75 kg (PMR)(W/kg) | : | (if applicable)

Capped speed process used during measurement | : | yes/no

Maximum speed of the vehicle | : |

Downscaling (if applicable) | : | yes/no

Downscaling factor fdsc | : |

Cycle distance (m) | : |

Constant speed (in the case of the shortened test procedure) | : | if applicable

Gear shifting | : | Average gear for v ≥ 1 km/h, x.xxxx

Test mass of VL(kg) | : |

f0 (N) | : |

f1 (N/(km/h)) | : |

f2 (N/(km/h)2) | : |

Cycle energy demand (J) | : |

Δ(CD × Af)LH (m2) | : |

Road load test report reference | : |

Road load family's identifier | : |

Cycle (without downscaling) | : | Class 1 / 2 / 3a / 3b

Ratio of rated power to mass in running order – 75 kg (PMR)(W/kg) | : | (if applicable)

Capped speed process used during measurement | : | yes/no

Maximum speed of the vehicle | : |

Downscaling (if applicable) | : | yes/no

Downscaling factor fdsc | : |

Cycle distance (m) | : |

Constant speed (in the case of the shortened test procedure) | : | if applicable

Gear shifting | : | Average gear for v ≥ 1 km/h, x,xxxx

Method of chassis dyno setting | : | Fixed run / iterative / alternative with its own warmup cycle

Dynamometer in 2WD/4WD operation | : | 2WD/4WD

For 2WD operation, was the non-powered axle rotating | : | yes/no/not applicable

Dynamometer operation mode | | yes/no

Coastdown mode | : | yes/no

Additional preconditioning | : |

yes/no

description

Deterioration factors | : | assigned / tested

Date(s) of test(s) | : | (day/month/year)

Place of the test(s) | : | Chassis dyno, location, country

Height of the lower edge above ground of cooling fan (cm) | : | | |

Lateral position of fan centre (if modified as request by the manufacturer) | : | in the vehicle centre-line/…

Distance from the front of the vehicle (cm) | : | | |

IWR: Inertial Work Rating (%) | : | x,x

RMSSE: Root Mean Squared Speed Error (km/h) | : | x,xx

Description of the accepted deviation of the driving cycle | : |

PEV before break off criteria

or

Fully operated acceleration pedal

For each driver selectable mode tested the points below shall be repeated (predominant mode or best case mode and worst case mode, if applicable)

Pollutants | CO | THC (a) | NMHC (a) | NOx | THC + NOx (b) | Particulate Matter | Particle Number

(mg/km) | (mg/km) | (mg/km) | (mg/km) | (mg/km) | (mg/km) | (#.1011/km)

Measured values | | | | | | |

Regeneration factors (Ki)(2)

Additive

Regeneration factors (Ki)(2)

Multiplicative

Deterioration factors (DF) additive | | | | | | |

Deterioration factors (DF) multiplicative | | | | | | |

Final values | | | | | | |

Limit values | | | | | | |

[Indicate as applicable.]

(2)

See Ki family report(s)

: |

Type 1/I performed for Ki determination | : | in accordance with Annex B4 to UN Regulation No 154 or UN/ECE Regulation No 83

Regeneration family's identifier | : |

Record test results in accordance with the table of Test 1

Record test results in accordance with the table of Test 1

Pollutant emission limits have to be fulfilled and the following point has to be repeated for each driven test cycle.

Pollutants | CO | THC (a) | NMHC (a) | NOx | THC + NOx (b) | Particulate Matter | Particle Number

(mg/km) | (mg/km) | (mg/km) | (mg/km) | (mg/km) | (mg/km) | (#.1011/km)

Measured single cycle values | | | | | | |

Limit single cycle values | | | | | | |

Record test results in accordance with the table of Test 1

Record test results in accordance with the table of Test 1

Pollutants | CO | THC (a) | NMHC (a) | NOx | THC + NOx (b) | Particulate Matter | Particle Number

(mg/km) | (mg/km) | (mg/km) | (mg/km) | (mg/km) | (mg/km) | (#.1011/km)

Calculated values | | | | | | |

For each driver selectable mode tested the points below have to be repeated (predominant mode or best case mode and worst case mode, if applicable)

CO2 emission | Low | Medium | High | Extra High | Combined

Measured value MCO2,p,1/ MCO2,c,2 | | | | |

Speed and distance corrected value MCO2,p,2b / MCO2,c,2b | | | | |

RCB correction coefficient: (5) | | | | |

MCO2,p,3 / MCO2,c,3 | | | | |

Regeneration factors (Ki)

Additive

Regeneration factors (Ki)

Multiplicative

MCO2,c,4 | — |

AFKi = MCO2,c,3 / MCO2,c,4 | — |

MCO2,p,4 / MCO2,c,4 | | | | | —

ATCT correction (FCF) (4) | | | | |

Temporary values MCO2,p,5 / MCO2,c,5 | | | | |

Declared value | — | — | — | — |

dCO21 * declared value | — | — | — | — |

(4)

FCF: family correction factor for correcting for representative regional temperature conditions (ATCT)

See ATCT family report(s) | : |

ATCT family's identifier | : |

(5)

correction as referred to in Annex B6 - Appendix 2 of UN Regulation No 154 for pure ICE vehicles, and Annex B8 - Appendix 2 of UN Regulation No 154 for HEVs (KCO2)

Record test results in accordance with the table of Test 1

Record test results in accordance with the table of Test 1

CO2 emission (g/km) | Low | Medium | High | Extra High | Combined

Averaging MCO2,p,6 / MCO2,c,6 | | | | |

Alignment MCO2,p,7 / MCO2,c,7 | | | | |

Final values MCO2,p,H / MCO2,c,H | | | | |

Information for Conformity of Production for OVC-HEV

Combined

CO2 emission (g/km)

MCO2,CS,COP

AFCO2,CS |

CO2 emission (g/km) | Combined

Calculated value MCO2,CD |

Declared value |

dCO21 |

Record test results in accordance with the table of Test 1

Record test results in accordance with the table of Test 1

CO2 emission (g/km) | Combined

Averaging MCO2,CD |

Final value MCO2,CD |

CO2 emission (g/km) | Combined

Calculated value MCO2,weighted |

For each driver selectable mode tested the points below has to be repeated (predominant mode or best case mode and worst case, mode if applicable)

[Calculated from aligned CO2 values.]

Fuel consumption (l/100 km) | Low | Medium | High | Extra High | Combined

Final values FCp,H / FCc,H | | | | |

A- On-board Fuel and/or Energy Consumption Monitoring for vehicles referred to in Article 4a

The parameters listed in point 3 of Annex XXII are accessible: yes/not applicable

[In the case that the OBFCM signal can only be read-out to 2 decimal places, the third decimal place shall be introduced as a zero.] [In accordance with Annex XXII.] [In accordance with Annex XXII.] [In accordance with Annex XXII.]

Fuel_ConsumedWLTP (litres) | Vehicle HIGH - Test 1 | x,xxx

Vehicle HIGH - Test 2 (if applicable) | x,xxx

Vehicle HIGH - Test 3 (if applicable) | x,xxx

Vehicle LOW - Test 1 (if applicable) | x,xxx

Vehicle LOW Test 2 (if applicable) | x,xxx

Vehicle LOW - Test 3 (if applicable) | x,xxx

Total | x,xxx

Fuel_ConsumedOBFCM (litres) | Vehicle HIGH - Test 1 | x,xxx

Vehicle HIGH - Test 2 (if applicable) | x,xxx

Vehicle HIGH - Test 3 (if applicable) | x,xxx

Vehicle LOW - Test 1 (if applicable) | x,xxx

Vehicle LOW Test 2 (if applicable) | x,xxx

Vehicle LOW - Test 3 (if applicable) | x,xxx

Total | x,xxx

Accuracy | x,xxx

Fuel consumption (l/100 km or kg/100 km) | Combined

Calculated value FCCD |

Record test results in accordance with the table of Test 1

Record test results in accordance with the table of Test 1

Fuel consumption (l/100km or kg/100 km) | Combined

Averaging FCCD |

Final value FCCD |

Fuel consumption (l/100 km or kg/100 km) | Combined

Calculated value FCweighted |

For each driver selectable mode tested the points below has to be repeated (predominant mode or best case mode and worst case, mode if applicable)

Fuel consumption (kg/100 km) | Combined

Measured values |

RCB correction coefficient |

Final values FCc |

AER (km) | City | Combined

Measured/Calculated values AER | |

Declared value | — |

Record test results in accordance with the table of Test 1

Record test results in accordance with the table of Test 1

AER (km) | City | Combined

Averaging AER (if applicable) | |

Final values AER | |

EAER (km) | Low | Medium | High | Extra High | City | Combined

Final values EAER | | | | | |

RCDA (km) | Combined

Final value RCDA |

RCDC (km) | Combined

Final value RCDC |

Index Number of the transition cycle |

REEC of confirmation-cycle (%) |

Record test results in accordance with the table of Test 1

Record test results in accordance with the table of Test 1

PER (km) | Low | Medium | High | Extra High | City | Combined

Calculated values PER | | | | | |

Declared value | — | — | — | — | — |

Record test results in accordance with the table of Test 1

Record test results in accordance with the table of Test 1

PER (km) | City | Combined

Averaging PER | |

Final values PER | |

EAC (Wh) |

EC (Wh/km) | Low | Medium | High | Extra High | City | Combined

Final values EC | | | | | |

ECAC,CD (Wh/km) | Combined

Calculated value ECAC,CD |

Record test results in accordance with the table of Test 1

Record test results in accordance with the table of Test 1

ECAC,CD (Wh/km) | Combined

Averaging ECAC,CD |

Final value |

ECAC,weighted (Wh) | Combined

Calculated value ECAC,weighted |

Record test results in accordance with the table of Test 1

Record test results in accordance with the table of Test 1

ECAC,weighted (Wh/km) | Combined

Averaging ECAC,weighted |

Final value |

Combined

Electric consumption (Wh/km) ECDC,CD,COP |

AFEC,AC,CD |

EC (Wh/km) | City | Combined

Calculated values EC | |

Declared value | — |

Record test results in accordance with the table of Test 1

Record test results in accordance with the table of Test 1

EC (Wh/km) | Low | Medium | High | Extra High | City | Combined

Averaging EC | | | | | |

Final values EC | | | | | |

Combined

Electric Consumption (Wh/km) ECDC,COP |

AFEC |

Repeat § 2.1.1.

Repeat § 2.1.1.

[Indicate for each pollutant the highest among the average test results of VH, VL (if applicable) and VM (if applicable).]

Pollutants | CO | THC (a) | NMHC (a) | NOx | THC + NOx (b) | PM | PN

(mg/km) | (mg/km) | (mg/km) | (mg/km) | (mg/km) | (mg/km) | (#.1011/km)

Highest values | | | | | | |

Included the emissions data required for roadworthiness testing

[Delete where not applicable (there are cases where nothing needs to be deleted when more than one entry is applicable).]

Test | CO ( % vol) | Lambda | Engine speed (min–1) | Oil temperature (°C)

Idle | | — | |

High idle | | | |

Emission of crankcase gases into the atmosphere: none

Family's identifier | : |

See report(s) | : |

[Indicate as applicable.]

Family's identifier | : |

See durability family report(s) | : |

Type 1/I cycle for criteria emissions testing | : | According to UN Regulation 154 Annex B4 or UN/ECE Regulation No 83

RDE family number | : | MSxxxx

See family report(s) | : |

Family's identifier | |

Date of tests | : | (day/month/year)

Place of tests | : |

Method of setting of the chassis dyno | : | coast down (road load reference)

Inertia mass (kg) | : |

If deviation from the vehicle of Type 1 test | : |

Tyres | : |

Make | : |

Type | : |

Dimensions front/rear | : |

Dynamic circumference (m) | : |

Tyre pressure (kPa) | : |

Pollutants |

CO

(g/km)

HC

(g/km)

Test | 1 | |

2 | |

3 | |

Average | |

Limit | |

Family's identifier | : |

See family report(s) | : |

See family report(s) | : |

Measured absorption value (m–1) | : |

Corrected absorption value (m–1) | : |

See report(s) or approval number | : |

[If ‘yes’ then the six last lines are not applicable.]

Worst case approach with regards to vehicle insulation | : | yes/no

Worst case approach vehicle cool down | : | yes/no(10)

ATCT family composed of a single Interpolation family | : | yes/no(10)

Engine coolant temperature at the end of soaking time (°C) | : |

Average soak area temperature over the 3 last hours (°C) | : |

Difference between engine coolant end temperature and average soak area temperature of the last 3 hours ΔT_ATCT (°C) | : |

The minimum soaking time tsoak_ATCT (s) | : |

Location of temperature sensor | : |

Measured engine temperature | : | oil/coolant

Family’s identifier | : |

See family report(s) | : |

The following information, if applicable, is the minimum data required for the ATCT test.

APPLICANT | | | |

Manufacturer | | | |

SUBJECT | …

Roadload family identifier(s) | : |

Interpolation family identifier(s) | : |

ATCT identifier(s) | : |

Object submitted to tests

Make | : |

IP identifier | : |

CONCLUSION | The object submitted to tests complies with the requirements mentioned in the subject.

PLACE, | DD/MM/YYYY

If there are several options (references), the one tested should be described in the test report

If there are not, a single reference to the information document at the start of the test report may be sufficient.

Every Technical Service is free to include some additional information

Characters are included in the sections of the test report relating to specific vehicle types, as follows:

‘(a)’ Specific to positive ignition engine vehicles.

‘(b)’ Specific to compression ignition engine vehicles.

Vehicle numbers | : | Prototype number and VIN

Category | : |

Bodywork | : |

Drive wheels | : |

Powertrain architecture | : | pure ICE, hybrid, electric or fuel cell

For more than one ICE, please repeat the point

[a tolerance of +/– 10 per cent is permitted for volume and weight]

Make | : | | | | | |

Type | : | | | | | |

Working principle | : | two/four stroke

Cylinders number and arrangement | : | …

Engine capacity (cm3) | : | | | | | |

Engine idling speed (min–1) | : | | | ±

High engine idling speed (min–1) (a) | : | | | ±

Rated engine power | : | | kW | at | | rpm

Maximum net torque | : | | Nm | at | | rpm

Engine lubricant | : | make and type

Cooling system | : | Type: air/water/oil

Insulation | : | material, amount, location, nominal volume and nominal weight

For more than one test fuel, please repeat the point

Make | : |

Type | : | Petrol E10 - Diesel B7 – LPG – NG - …

Density at 15 °C | : |

Sulphur content | : | Only for Diesel and Petrol

Annex IX | : |

Batch number | : |

Willans factors (for ICE) for CO2 emission (gCO2/MJ) | : |

Direct injection | : | yes/no or description

Vehicle fuel type | : | Monofuel / bifuel / flex fuel

Control unit | |

Part reference | : | same as information document

Software tested | : | read via scantool, for example

Air flowmeter | : |

Throttle body | : |

Pressure sensor | : |

Injection pump | : |

Injector(s) | : |

For more than one fuel feed system, please repeat the point

For more than one intake system, please repeat the point

Pressure charger | : |

Yes/no

make & type (1)

Intercooler | : |

yes/no

type (air/air – air/water) (1)

Air filter (element) (1) | : | make & type

Intake silencer (1) | : | make & type

For more than one, please repeat the point

First catalytic converter | : |

make & reference (1)

principle: three way / oxidising / NOx trap / Nox storage system / Selective Catalyst Reduction…

Second catalytic converter | : |

make & reference (1)

principle: three way / oxidising / NOx trap / Nox storage system / Selective Catalyst Reduction…

Particulate trap | : |

with/without/not applicable

catalysed: yes/no

make & reference (1)

Reference and position of oxygen sensor(s) | : | before catalyst / after catalyst

Air injection | : | with/without/not applicable

EGR | : |

with/without/not applicable

cooled/non-cooled

HP/LP

Evaporative emission control system | : | with/without/not applicable

Reference and position of NOx sensor(s) | : | Before/ after

General description (1) | : |

For more than one Heat Storage System, please repeat the point

Heat storage device | : | yes/no

Heat capacity (enthalpy stored J) | : |

Time for heat release (s) | : |

For more than one Transmission, please repeat the point

Gearbox | : | manual / automatic / continuous variation

Gear shifting procedure

Predominant mode | : |

yes/no

normal / drive / eco/…

Best case mode for CO2 emissions and fuel consumption (if applicable) | : |

Worst case mode for CO2 emissions and fuel consumption (if applicable) | : |

Control unit | : |

Gearbox lubricant | : | make and type

Tyres

Make | : |

Type | : |

Dimensions front/rear | : |

Dynamic circumference (m) | : |

Tyre pressure (kPa) | : |

This article is long: the rest is at the official publication.