26 ANNEX IIIA, Regulation (EU) 2017/1151

In forcesince 13 Aug 2026

Abbreviations refer generically to both the singular and the plural forms of abbreviated terms.

CLD | — | ChemiLuminescence Detector

CVS | — | Constant Volume Sampler

DCT | — | Dual Clutch Transmission

ECU | — | Engine Control Unit

EFM | — | Exhaust mass Flow Meter

FID | — | Flame Ionisation Detector

FS | — | full scale

GNSS | — | Global Navigation Satellite System

HCLD | — | Heated ChemiLuminescence Detector

ICE | — | Internal Combustion Engine

LPG | — | Liquid Petroleum Gas

NDIR | — | Non-Dispersive InfraRed analyser

NDUV | — | Non-Dispersive UltraViolet analyser

NG | — | Natural Gas

NMC | — | Non-Methane Cutter

NMC-FID | — | Non-Methane Cutter in combination with a Flame-Ionisation Detector

NMHC | — | Non-Methane HydroCarbons

OBD | — | On-Board Diagnostics

PEMS | — | Portable Emissions Measurement System

RPA | — | Relative Positive Acceleration

SEE | — | Standard Error of Estimate

THC | — | Total HydroCarbons

VIN | — | Vehicle Identification Number

WLTC | — | Worldwide harmonized Light vehicles Test Cycle

2.1.

For the purposes of this Annex, the following definitions shall apply in terms of generic issues:

2.1.1. ‘Vehicle type with regard to Real Driving Emissions’ means a group of vehicles which do not differ with respect to the criteria constituting a ‘PEMS test family’ as defined in point 3.3.1.

2.1.2. ‘Declared Maximum RDE’ means the emission values, which must necessarily be lower than the applicable emission limits, declared optionally by the manufacturer and used for checking compliance against lower emission limits

2.2.

For the purposes of this Annex, the following definitions shall apply in terms of test equipment:

2.2.1. ‘Accuracy’ means the difference between a measured value and a reference value, traceable to a national or international standard and describes the correctness of a result (Figure 1).

2.2.2. ‘Adapter’ means in the context of this annex mechanical parts that allow the connection of the vehicle to a commonly used or standardized measurement device connector.

2.2.3. ‘Analyser’ means any measurement device that is not part of the vehicle but installed to determine the concentration or the amount of gaseous or particle pollutants.

2.2.4. ‘Calibration’ means the process of setting a measurement system's response so that its output agrees with a range of reference signals.

2.2.5. ‘Calibration gas’ means a gas mixture used to calibrate gas analysers.

2.2.6. ‘Delay time’ means the difference in time between the change of the component to be measured at the reference point and a system response of 10 per cent of the final reading (t10) with the sampling probe being defined as the reference point (Figure 2).

2.2.7. ‘Full scale’ means the full range of an analyser, flow-measuring instrument or sensor as specified by the equipment manufacturer or the highest range used for the specific test.

2.2.8. ‘Hydrocarbon response factor’ of a particular hydrocarbon species means the ratio between the reading of a FID and the concentration of the hydrocarbon species under consideration in the reference gas cylinder, expressed as ppmC1.

2.2.9. ‘Major maintenance’ means the adjustment, repair or replacement of a component or module that could affect the accuracy of a measurement.

2.2.10. ‘Noise’ means two times the root mean square of ten standard deviations, each calculated from the zero responses measured at a constant frequency which is a multiple of 1,0 Hz during a period of 30 seconds.

2.2.11. ‘Non-methane hydrocarbons’ (NMHC) means the Total Hydrocarbons (THC) minus the methane (CH4) contribution.

2.2.12. ‘Precision’ means the degree to which repeated measurements under unchanged conditions show the same results (Figure 1).

2.2.13. ‘Reading’ means the numerical value displayed by an analyser, flow-measuring instrument, sensor or any other measurement devise applied in the context of vehicle emission measurements.

2.2.14. ‘Reference value’ means a value traceable to a national or international standard (Figure 1).

2.2.15. ‘Response time’ (t90) means the difference in time between the change of the component to be measured at the reference point and a system response of 90 per cent of the final reading (t90) with the sampling probe being defined as the reference point, whereby the change of the measured component is at least 60 per cent full scale (FS) and takes place in less than 0.1 second. The system response time consists of the delay time to the system and of the rise time of the system as depicted in Figure 2.

2.2.16. ‘Rise time’ means the difference in time between the 10 per cent and 90 per cent response of the final reading (t10 to t90) as depicted in Figure 2.

2.2.17. ‘Sensor’ means any measurement device that is not part of the vehicle itself but installed to determine parameters other than the concentration of gaseous and particle pollutants and the exhaust mass flow.

2.2.18. ‘Set point’ means the target value a control system aims to reach.

2.2.19. ‘Span’ means to adjust an instrument so that it gives a proper response to a calibration standard that represents between 75 per cent and 100 per cent of the maximum value in the instrument range or expected range of use.

2.2.20. ‘Span response’ means the mean response to a span signal over a time interval of at least 30 seconds.

2.2.21. ‘Span response drift’ means the difference between the mean response to a span signal and the actual span signal that is measured over a defined time period after an analyser, flow-measuring instrument or sensor has been accurately spanned.

2.2.22. ‘Total hydrocarbons’ (THC) means the sum of all volatile compounds measurable by a flame ionization detector (FID).

2.2.23. ‘Traceable’ means the ability to relate a measurement or reading through an unbroken chain of comparisons to a national or international standard.

2.2.24. ‘Transformation time’ means the time difference between a change of concentration or flow (t0) at the reference point and a system response of 50 per cent of the final reading (t50) as depicted in Figure 2.

2.2.25. ‘Type of analyser’, also referred to as ‘analyser type’ means a group of analysers produced by the same manufacturer that apply an identical principle to determine the concentration of one specific gaseous component or the number of particles.

2.2.26. ‘Type of exhaust mass flow meter’ means a group of exhaust mass flow meters produced by the same manufacturer that share a similar tube inner diameter and function on an identical principle to determine the mass flow rate of the exhaust gas.

2.2.27. ‘Verification’ means the process of evaluating whether the measured or calculated output of an analyser, flow-measuring instrument, sensor or signal or method agrees with a reference signal or value within one or more predetermined thresholds for acceptance.

2.2.28. ‘Zero’ means the calibration of an analyser, flow-measuring instrument or sensor so that it gives an accurate response to a zero signal.

2.2.29. ‘Zero gas’ means a gas containing no analyte, which is used to set a zero response on an analyser.

2.2.30. ‘Zero response’ means the mean response to a zero signal over a time interval of at least 30 seconds.

2.2.31. ‘Zero response drift’ means the difference between the mean response to a zero signal and the actual zero signal that is measured over a defined time period after an analyser, flow-measuring instrument or sensor has been accurately zero calibrated.

2.3.

For the purposes of this Annex, the following definitions shall apply in terms of vehicle characteristics and driver:

2.3.1. ‘Actual mass of the vehicle’ means the mass in running order plus the mass of the fitted optional equipment to an individual vehicle.

2.3.2. ‘Auxiliary devices’ means energy consuming, converting, storing or supplying non-peripheral devices or systems which are installed in the vehicle for purposes other than the propulsion of the vehicle and are therefore not considered to be part of the powertrain.

2.3.3. ‘Mass in running order’ means the mass of the vehicle, with its fuel tank(s) filled to at least 90 per cent of its or their capacity/capacities, including the mass of the driver, fuel and liquids, fitted with the standard equipment in accordance with the manufacturer's specifications and, when they are fitted, the mass of the bodywork, the cabin, the coupling and the spare wheel(s) as well as the tools.

2.3.4. ‘Maximum Permissible Test mass of the vehicle’ means the sum of the actual mass of the vehicle and 90 per cent of the difference between the technically permissible maximum laden mass and the actual mass of the vehicle (Figure 3).

2.3.5. ‘Odometer’ means an instrument indicating to the driver the total distance driven by the vehicle since its production.

2.3.6. ‘Optional equipment’ means all the features not included in the standard equipment which are fitted to a vehicle under the responsibility of the manufacturer, and that can be ordered by the customer.

2.3.7. ‘Power-to-test mass-ratio’ corresponds to the ratio of the rated engine power of the internal combustion engine over the test mass (i.e. the actual mass of the vehicle plus the mass of the measurement equipment and the mass of additional passengers or payload, if any).

2.3.8. ‘Power-to-mass-ratio’ is the ratio of rated power to the mass in running order.

2.3.9. ‘Rated engine power (Prated)’ means maximum net power of the engine or motor in kW as per the requirements of UN Regulation No 85 [Regulation No 85 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of internal combustion engines or electric drive trains intended for the propulsion of motor vehicles of categories M and N with regard to the measurement of net power and the maximum 30 minutes power of electric drive trains (OJ L 323, 7.11.2014, p. 52).].

2.3.10. ‘Technically permissible maximum laden mass’ means the maximum mass allocated to a vehicle on the basis of its construction features and its design performances.

2.3.11. ‘Vehicle OBD information’ means information relating to an on-board diagnostic system for any electronic system on the vehicle

2.3.12. ‘Flex fuel vehicle’ means a vehicle with one fuel storage system that can run on different mixtures of two or more fuels.

2.3.13. ‘Mono-fuel vehicle’ means a vehicle that is designed to run primarily on one type of fuel.

2.3.14. ‘Not off-vehicle charging hybrid electric vehicle’ (NOVC-HEV) means a hybrid electric vehicle that cannot be charged from an external source.

2.3.15. ‘Off-vehicle charging hybrid electric vehicle’ (OVC-HEV) means a hybrid electric vehicle that can be charged from an external source.

2.4.1. ‘Coefficient of determination’ (r2) means:

r21

ni 1

yi a0 a1 xi2

ni 1

yi

y

2

where:

a0is the axis intercept of the linear regression line

a1is the slope of the linear regression line

xiis the measured reference value

yiis the measured value of the parameter to be verified

y

is the mean value of the parameter to be verified

nis the number of values

2.4.2. ‘Cross-correlation coefficient’ (r) means:

r

n 1i 1

xi

x

yi

y

n 1i 1

xi

x

2

n 1i 1

yi

y

2

where:

xiis the measured reference value

yiis the measured value of the parameter to be verified

x

is the mean reference value

y

is the mean value of the parameter to be verified

nis the number of values

2.4.3. ‘Root mean square’ (xrms) means the square root of the arithmetic mean of the squares of values and defined as:

xrms1

n

ni 1

xi2

where:

xiis the measured or calculated value

nis the number of values

2.4.4. ‘Slope’ of a linear regression (a1) means:

a1

ni 1

xi

x

yi

y

ni 1

xi

x

2

where:

xiis the actual value of the reference parameter

yiis the actual value of the parameter to be verified

x

is the mean value of the reference parameter

y

is the mean value of the parameter to be verified

nis the number of values

2.4.5. ‘Standard error of estimate’ (SEE) means:

SEE

ni 1

yi ý2

n 2

where:

ýis the estimated value of the parameter to be verified

yiis the actual value of the parameter to be verified

nis the number of values

2.5.1. ‘Cold start period’ means the period from the test start as defined in point 2.6.5 until the point when the vehicle has run for 5 minutes. If the coolant temperature is determined, the cold start period ends once the coolant is at least 70 °C for the first time but no later than 5 minutes after test start. In the case that measuring the coolant temperature is not feasible, on request of the manufacturer and with approval of the approval authority, instead of using the coolant temperature, the engine oil temperature may be used.

2.5.2. ‘Deactivated internal combustion engine’ means an internal combustion engine for which one of the following criteria apply:

the recorded engine speed is < 50 rpm;

or when the engine speed is not recorded, the exhaust mass flow rate is measured at < 3 kg/h.

2.5.3. ‘Engine control unit’ means the electronic unit that controls various actuators to ensure the optimal performance of the engine.

2.5.4. ‘Extended factor’ means a factor which accounts for the effect of extended ambient temperature or altitude conditions upon pollutant emissions.

2.5.5. ‘Particle number emissions’ (PN) means the total number of solid particles [The term ‘particle’ is conventionally used for the matter being characterised (measured) in the airborne phase (suspended matter), and the term ‘particulate’ for the deposited matter.] emitted from the vehicle exhaust quantified according to the dilution, sampling and measurement methods as specified in this Annex.

2.6.1. ‘Cold start PEMS trip’ means a trip with conditioning of the vehicle prior to the test as described in paragraph 5.3.2.

2.6.2. ‘Hot start PEMS trip’ means a trip without conditioning of the vehicle prior to the test as described in paragraph 5.3.2, but with a warm engine with coolant temperature above 70 °C. In the case that measuring the coolant temperature is not feasible, on request of the manufacturer and with approval of the approval authority, instead of using the coolant temperature, the engine oil temperature may be used.

2.6.3. ‘Periodically regenerating system’ means a pollutant emissions control device (e.g. catalytic converter, particulate trap) that requires a periodical regeneration

2.6.4. ‘Reagent’ means any product other than fuel that is stored on-board the vehicle and is provided to the exhaust after-treatment system upon request of the emission control system.

2.6.5. ‘Test start’ means (Figure 4) whichever occurs first from:

the first activation of the internal combustion engine;

the first movement of the vehicle with speed greater than 1 km/h for OVC-HEVs and NOVC-HEVs.

2.6.6. ‘Test end’ means (Figure 5) that the vehicle has completed the trip and whichever occurs last from:

the final deactivation of the internal combustion engine;

the vehicle stops and the speed is lower than or equal to 1 km/h for OVC-HEVs and NOVC-HEVS finishing the test with deactivated internal combustion engine.

2.6.7. ‘Validation of PEMS’ means the process of evaluating on a chassis dynamometer the correct installation and functionality within the given accuracy limits of a Portable Emissions Measurement System and exhaust mass flow rate measurements as obtained from one or multiple non-traceable exhaust mass flow meters or as calculated from sensors or ECU signals.

For vehicle types approved according to this Annex, the final RDE emission results calculated according to this Annex at any possible RDE test performed in accordance with the requirements of this Annex, shall not be higher than any of the relevant Euro 6 emission limits laid down in Table 2 of Annex I to Regulation (EC) No 715/2007. The manufacturer shall confirm compliance with this Regulation by completing the RDE compliance certificate set out in Appendix 12.

The manufacturer may declare compliance with lower emission limits by declaring lower values called ‘Declared Maximum RDE’, either for NOx or PN or both, in the Manufacturer’s RDE certificate of compliance found in Appendix 12 and the Certificate of Conformity of each vehicle. These Declared Maximum RDE values shall be used for checking the compliance of cars when applicable, including for tests performed during In-service Conformity and Market Surveillance.

The RDE performance shall be demonstrated by performing the necessary tests in the PEMS test family on the road operated over their normal driving patterns, conditions and payloads. The necessary tests shall be representative for vehicles operated on their real driving routes, with their normal load. The requirements of emission limits shall be fulfilled for the urban operation and the complete PEMS trip.

The RDE tests required by this Annex provide a presumption of conformity. The presumed conformity may be reassessed by additional RDE tests. Verification of compliance shall be made in accordance with the rules of in-service conformity.

Member States shall ensure that vehicles can be tested with PEMS on public roads in accordance with the procedures under their own national law, while respecting local road traffic legislation and safety requirements.

Manufacturers shall ensure that vehicles can be tested with PEMS. This shall include:

(a)

constructing the exhaust pipes in order to facilitate sampling of the exhaust, or making available suitable adapters for exhaust pipes for testing by the authorities;

(b)

in case the exhaust pipe construction does not facilitate sampling of the exhaust, the manufacturer shall also make available to independent parties, adapters for purchase or rent via their spare parts or service tools network (e.g. RMI portal), through authorised dealers or via a contact point on the referred publicly accessible website;

(c)

providing guidance available online, without the need of registration or login, on how to attach a PEMS to vehicles;

(d)

granting access to ECU signals relevant to this Annex, as mentioned in Table A4/1 of Appendix 4; and

(e)

making the necessary administrative arrangements.

PEMS tests shall not be required for each ‘vehicle type with regard to emissions’. Several vehicle emission types may be put together by the vehicle manufacturer to form a ‘PEMS test family’ in accordance with the requirements of paragraph 3.3.1, which shall be validated in accordance with the requirements of paragraph 3.4.

N | — | Number of vehicle emission types

NT | — | Minimum number of vehicle emission types

PMRH | — | highest power-to-mass-ratio of all vehicles in the PEMS test family

PMRL | — | lowest power-to-mass-ratio of all vehicles in the PEMS test family

V_eng_max | — | maximum engine volume of all vehicles within the PEMS test family

A PEMS test family shall comprise finished vehicles of a manufacturer with similar emission characteristics. Vehicle emission types may be included in a PEMS test family only as long as the vehicles within a PEMS test family are identical with respect to the characteristics in all the administrative and technical criteria listed below.

(a)

The approval authority issuing the emission type approval in accordance with this Annex (‘authority’)

(b)

The manufacturer having received the emission type approval in accordance with this Annex (‘manufacturer’).

(a)

Propulsion type (e.g. ICE, NOVC-HEV, OVC-HEV)

(b)

Type(s) of fuel(s) (e.g. petrol, diesel, LPG, NG, …). Bi- or flex-fuelled vehicles may be grouped with other vehicles, with which they have one of the fuels in common.

(c)

Combustion process (e.g. two stroke, four stroke)

(d)

Number of cylinders

(e)

Configuration of the cylinder block (e.g. in-line, V, radial, horizontally opposed, …)

(f)

Engine volume

The vehicle manufacturer shall specify a value V_eng_max (= maximum engine volume of all vehicles within the PEMS test family). The engine volumes of vehicles in the PEMS test family shall not deviate more than – 22 % from V_eng_max if V_eng_max ≥ 1500 ccm and – 32 % from V_eng_max if V_eng_max < 1500 ccm.

(g)

Method of engine fuelling (e.g. indirect or direct or combined injection)

(h)

Type of cooling system (e.g. air, water, oil)

(i)

Method of aspiration such as naturally aspirated, pressure charged, type of pressure charger (e.g. externally driven, single or multiple turbo, variable geometries …)

(j)

Types and sequence of exhaust after-treatment components (e.g. three-way catalyst, oxidation catalyst, lean NOx trap, SCR, lean NOx catalyst, particulate trap)

(k)

Exhaust gas recirculation (with or without, internal/external, cooled/non-cooled, low/high pressure)

An existing PEMS test family may be extended by adding new vehicle emission types to it. The extended PEMS test family and its validation must also fulfil the requirements of paragraphs 3.3. and 3.4. This may require the PEMS testing of additional vehicles to validate the extended PEMS test family according to paragraph 3.4.

As an alternative to the provisions of paragraph 3.3.1.1 and 3.3.1.2. the vehicle manufacturer may define a PEMS test family that is identical to a single vehicle emission type or a single WLTP IP-family. In this case, only one vehicle has to be tested from the family in either a hot or a cold test, at the choice of the authority and there is no need to validate the PEMS test family as in paragraph 3.4.

3.4.1.1. The vehicle manufacturer shall present a representative vehicle of the PEMS test family to the authority. The vehicle shall be subject to a PEMS test carried out by a Technical Service to demonstrate compliance of the representative vehicle with the requirements of this Annex.

3.4.1.2. The authority shall select additional vehicles according to the requirements of paragraph 3.4.3. for PEMS testing carried out by a Technical Service to demonstrate compliance of the selected vehicles with the requirements of this Annex. The technical criteria for selection of an additional vehicle according to paragraph 3.4.3. shall be recorded with the test results.

This article is long: the rest is at the official publication.