1.1.1. The additional requirements for granting of type-approval for mono fuel gas vehicles, and bi-fuel gas vehicles shall be those set out in paragraph 5.9. of UN Regulation No 154. The reference to the information document in paragraph 5.9.1. of UN Regulation No 154 shall be understood as being reference to Appendix 3 of Annex I of this Regulation.
The additional requirements for granting of type-approval for flex fuel vehicles shall be those set out in paragraph 5.8. of UN Regulation No 154.
2.1.1. List of legislative acts referred to in Article 3(3):
Legislative Act | Requirements
The California Code of Regulations, Title 13, Sections 1961(a) and 1961(b)(1)(C)(1) applicable to 2001 and later model year vehicles, 1968.1, 1968.2, 1968.5, 1976 and 1975, published by Barclay’s Publishing | Type-approval must be granted under the California Code of Regulations applicable to the most recent model year of light-duty vehicle.
2.2.1. The requirements for inlets to fuel tanks shall be those specified in paragraphs 6.1.5. and 6.1.6. of UN Regulation 154.
2.3.1. The requirements for electronic system security of paragraph 6.1.7. of UN Regulation 154 shall be complied with. The effective application of these strategies in protecting the emission control systems may be tested during type approval and/or market surveillance.
2.3.2 Manufacturers shall effectively deter reprogramming of the odometer readings, in the board network, in any powertrain controller as well as in the transmitting unit for remote data exchange if applicable. Manufacturers shall include systematic tamper-protection strategies and write-protect features to protect the integrity of the odometer reading. Methods giving an adequate level of tamper protection shall be approved by the approval authority. The effective application of these strategies in protecting the odometer may be tested during type approval and/or market surveillance.
2.4.1. Figure I.2.4 illustrates the application of the tests for type-approval of a vehicle. The specific test procedures are described in Annexes II, IIIA, IV, V, VI, VII, VIII, XI, XVI, XX, XXI and XXII.
[Specific test procedures for hydrogen vehicles and flex fuel biodiesel vehicles will be defined at a later stage.] [Particulate mass and particle number limits and respective measurement procedures shall apply only to vehicles with direct injection engines.] [When a bi-fuel vehicle is combined with a flex fuel vehicle, both test requirements are applicable.] [Only NOx emissions shall be determined when the vehicle is running on hydrogen.] [Particulate mass and particle number limits and respective measurement procedures shall not apply.] [The particle number RDE test only applies to vehicles for which Euro 6 PN emission limits are defined in Table 2 of Annex I to Regulation (EC) No 715/2007.] [For applicability of measured components to fuels and vehicle technology and therefore measurement procedures, see the emission limits as defined in Table 2 of Annex I to Regulation (EC) No 715/2007.] [An actual test may not be necessary, see UN Regulation No 24 for details.] [Only fuel consumption shall be determined when the vehicle is running on hydrogen.] [Measuring of CO2 emissions is not required.]
Vehicle category | Vehicles with positive ignition engines including hybrids | Vehicles with compression ignition engines including hybrids | Pure electric vehicles | Hydrogen fuel cell vehicles
Mono fuel | Bi-fuel | Flex-fuel | Mono fuel | |
Reference fuel | Petrol | LPG | NG/Biomethane | Hydrogen (ICE) | Petrol | Petrol | Petrol | Petrol | Diesel | Petrol | — | Hydrogen (Fuel Cell)
LPG | NG/Biomethane |
Hydrogen
(ICE)
Ethanol (E85)
Type 1 test | Yes | Yes | Yes | Yes |
Yes
(both fuels)
Yes
(both fuels)
Yes
(both fuels)
Yes
(both fuels)
Yes | Yes | — | —
ATCT
(14 °C test)
Yes | Yes | Yes | Yes |
Yes
(both fuels)
Yes
(both fuels)
Yes
(both fuels)
Yes
(both fuels)
Yes | Yes | — | —
Gaseous pollutants, RDE (Type 1A test) | Yes | Yes | Yes | Yes |
Yes
(both fuels)
Yes
(both fuels)
Yes
(both fuels)
Yes
(both fuels)
Yes | Yes | — | —
PN, RDE (Type 1A test) | Yes | — | — | — |
Yes
(petrol only)
Yes
(petrol only)
Yes
(petrol only)
Yes
(both fuels)
Yes | Yes | — | —
Idle emissions
(Type 2 test)
Yes | Yes | Yes | — |
Yes
(both fuels)
Yes
(both fuels)
Yes
(petrol only)
Yes
(both fuels)
| — | — | —
Crankcase emissions
(Type 3 test)
Yes | Yes | Yes | — |
Yes
(petrol only)
Yes
(petrol only)
Yes
(petrol only)
Yes
(petrol only)
| — | — | —
Evaporative emissions
(Type 4 test)
Yes | — | — | — |
Yes
(petrol only)
Yes
(petrol only)
Yes
(petrol only)
Yes
(petrol only)
| Yes | — | —
Durability
(Type 5 test)
Yes | Yes | Yes | Yes |
Yes
(petrol only)
Yes
(petrol only)
Yes
(petrol only)
Yes
(petrol only)
Yes | Yes | — | —
Low temperature emissions
(Type 6 test)
Yes | — | — | — |
Yes
(petrol only)
Yes
(petrol only)
Yes
(petrol only)
Yes
(both fuels)
| — | — | —
In-service conformity | Yes | Yes | Yes | Yes |
Yes
(as at type approval)
Yes
(as at type approval)
Yes
(as at type approval)
Yes
(as at type approval)
Yes | Yes | — | —
OBD | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | — | —
CO2 emissions, fuel consumption, electric energy consumption and electric range | Yes | Yes | Yes | Yes |
Yes
(both fuels)
Yes
(both fuels)
Yes (petrol),
Yes (hydrogen)
Yes
(both fuels)
Yes | Yes | Yes | Yes
Smoke opacity | — | — | — | — | — | — | — | — | Yes | — | — | —
Engine power | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes
OBFCM | Yes | — | — | — | — | — | — |
Yes
(both fuels)
Yes | Yes | — | —
3.1.1. The type-approval shall be extended to vehicles if they conform to the requirements of paragraph 7.4. of UN Regulation No 154. The pollutant emissions shall respect the limits set out in Table 2 of Annex I to Regulation (EC) No 715/2007.
3.2.1. For tests performed in accordance with Annex 6 to UN/ECE Regulation No 83 [1 day NEDC] or the Annex to Regulation (EC) No 2017/1221 [2 days NEDC] the type-approval shall be extended to vehicles equipped with a control system for evaporative emissions which meet the following conditions:
3.2.1.1. The basic principle of fuel/air metering is the same.
3.2.1.2. The shape of the fuel tank is identical and the material of the fuel tank and liquid fuel hoses are technically equivalent.
3.2.1.3. The worst-case vehicle with regard to the cross-section and approximate hose length shall be tested. Whether non-identical vapour/liquid separators are acceptable is decided by the technical service responsible for the type-approval tests.
3.2.1.4. The fuel tank volume is within a range of ± 10 %.
3.2.1.5. The setting of the fuel tank relief valve is identical.
3.2.1.6. The method of storage of the fuel vapour is identical, i.e. trap form and volume, storage medium, air cleaner (if used for evaporative emission control), etc.
3.2.1.7. The method of purging of the stored vapour is identical (e.g. air flow, start point or purge volume over the preconditioning cycle).
3.2.1.8. The method of sealing and venting of the fuel metering system is identical.
3.2.2. For tests performed in accordance with Annex VI [2 days WLTP] the type-approval shall be extended to vehicles belonging to an approved evaporative emission family as defined in paragraph 6.6.3 of UN Regulation 154.
3.3.1. The deterioration factors shall be extended to different vehicles and vehicle types, provided that the requirements of paragraph 7.6. of UN Regulation No 154 are complied with.
3.4.1. The type-approval shall be extended to vehicles belonging to an approved OBD family as defined in paragraph 6.8.1 of UN Regulation No 154.
3.5.1.1. The type-approval shall be extended only to vehicles with a reference mass requiring the use of the next two higher equivalent inertia or any lower equivalent inertia.
3.5.1.2. For category N vehicles, the approval shall be extended only to vehicles with a lower reference mass, if the emissions of the vehicle already approved are within the limits prescribed for the vehicle for which extension of the approval is requested.
3.5.2.1. The type-approval shall be extended to vehicles with different transmission ratios only under certain conditions.
3.5.2.2. To determine whether type-approval can be extended, for each of the transmission ratios used in the type 6 test, the proportion,
(E) = |(V2-V1)|/V1
shall be determined where, at an engine speed of 1000 min–1, V1 is the speed of the vehicle-type approved and V2 is the speed of the vehicle type for which extension of the approval is requested.
3.5.2.3. If, for each transmission ratio, E ≤ 8 %, the extension shall be granted without repeating the type 6 test.
3.5.2.4. If, for at least one transmission ratio, E > 8 %, and if, for each gear ratio, E ≤ 13 %, the type 6 test shall be repeated. The tests may be performed in a laboratory chosen by the manufacturer subject to the approval of the technical service. The report of the tests shall be sent to the technical service responsible for the type-approval tests.
The type-approval shall be extended to vehicles with different reference masses and transmission ratios, provided that all the conditions prescribed in paragraphs 3.5.1 and 3.5.2 are fulfilled.
4.1.1. Every vehicle produced under a Type Approval according to this Regulation shall be so manufactured as to conform to the type approval requirements of this Regulation. The Manufacturer shall implement adequate arrangements and documented control plans and carry-out at specified intervals as given in this regulation the necessary emission, OBFCM and OBD tests to verify continued conformity with the approved type. The approval authority shall verify and agree with these arrangements and control plans of the manufacturer and perform audits and conduct emission, OBFCM and OBD tests at specific intervals, as given in this regulation, at the premises of the manufacturer, including production and test facilities as part of the product conformity and continued verification arrangements as described in Annex IV of Regulation (EU) 2018/858.
4.1.2. The manufacturer shall check the conformity of production by testing the emissions of pollutants (given in Table 2 of Annex I to Regulation (EC) No 715/2007), the emission of CO2 (along with the measurement of electric energy consumption and, where applicable, the monitoring of the OBFCM device accuracy), the crankcase emissions, evaporative emissions and the OBD in accordance with the test procedures described in Annexes V, VI, XI, XXI and XXII. The verification shall therefore include the tests of types 1, 3, 4, the tests for OBFCM and OBD, as described in section 2.4.
The type approval authority shall keep record for a period of at least 5 years of all the documentation related to the conformity of production test results and shall make it available to the Commission upon request.
The specific procedures for conformity of production are set out in paragraphs 8 and 9 and Appendixes 1 to 4 of UN Regulation No 154, with the following exception:
Table 8/1 in paragraph 8.1.2. of UN Regulation No 154 shall be replaced with:
[Only if there is combustion engine operation during a valid CD Type 1 test for CoP verification]
Type of vehicle | Pollutant emissions | CO2 emissions | Electric energy consumption | OBFCM accuracy
Pure ICE | Yes | Yes | Not Applicable | Yes
NOVC-HEV | Yes | Yes | Not Applicable | Yes
OVC-HEV |
Yes:
CD and CS
:CS only | Yes: CD only | Yes: CS
PEV | Not Applicable | Not Applicable | Yes | Not Applicable
NOVC-FCHV | Not Applicable | Not Applicable | Not Applicable | Not Applicable
OVC-FCHV | Not Applicable | Not Applicable | Exempted | Not Applicable
The calculation of additional values required for checking the Conformity of Production of electric energy consumption of PEVs and OVC-HEVs is set out in Appendix 8 of Annex B8 to UN Regulation 154.
4.1.8. In case of non-conformity Article 51 of Regulation (EU) 2018/858 shall apply.
4.2.6. Vehicles fitted with eco-innovations
4.2.6.1. In the case of a vehicle type fitted with one or more eco-innovations, within the meaning of Article 11 of Regulation (EU) 2019/631 [Regulation (EU) 2019/631 of the European Parliament and of the Council of 17 April 2019 setting CO2 emission performance standards for new passenger cars and for new light commercial vehicles, and repealing Regulations (EC) No 443/2009 and (EU) No 510/2011 (OJ L 111, 25.4.2019, p. 13).] for M1 or for N1 vehicles, the conformity of production shall be demonstrated with respect to the eco-innovations, by checking the presence of the correct eco-innovation(s) in question.
4.5.1. If a verification of the Type 3 test is to be carried out, it shall be conducted in accordance with the following requirements:
4.5.1.1. When the approval authority determines that the quality of production seems unsatisfactory, a vehicle shall be randomly taken from the family and subjected to the tests described in Annex V.
4.5.1.2. The production shall be deemed to conform if this vehicle meets the requirements of the tests described in Annex V.
4.5.1.3. If the vehicle tested does not satisfy the requirements of Section 4.5.1.1, a further random sample of four vehicles shall be taken from the same family and subjected to the tests described in Annex V. The tests may be carried out on vehicles which have completed a maximum of 15000 km with no modifications.
4.5.1.4. The production shall be deemed to conform if at least three vehicles meet the requirements of the tests described in Annex V.
4.6.1. If a verification of the Type 4 test is to be carried out, it shall be conducted in accordance with the following requirements:
4.6.1.1. When the approval authority determines that the quality of production seems unsatisfactory, a vehicle shall be randomly taken from the family and subjected to the tests described in Annex VI, or at least as in paragraph 7 of Annex 7 of UN Regulation 83.
4.6.1.2. The production shall be deemed to conform if this vehicle meets the requirements of the tests described in Annex VI, or paragraph 7 of Annex 7 of UN Regulation 83 depending on the test performed.
4.6.1.3. If the vehicle tested does not satisfy the requirements of section 4.6.1.1, a further random sample of four vehicles shall be taken from the same family and subjected to the tests described in Annex VI, or at least as in paragraph 7 of Annex 7 of UN Regulation 83. The tests may be carried out on vehicles which have completed a maximum of 15000 km with no modifications.
4.6.1.4. The production shall be deemed to conform if at least three vehicles meet the requirements of the tests described in Annex VI, or paragraph 7 of Annex 7 of UN Regulation 83 depending on the test performed.
4.7.1. If a verification of the performance of the OBD system is to be carried out, it shall be conducted in accordance with the following requirements:
4.7.1.1. When the approval authority determines that the quality of production seems unsatisfactory, a vehicle shall be randomly taken from the family and subjected to the tests described in Appendix 1 to Annex XI.
4.7.1.2. The production shall be deemed to conform if this vehicle meets the requirements of the tests described in Appendix 1 to Annex XI.
4.7.1.3. If the vehicle tested does not satisfy the requirements of section 4.7.1.1, a further random sample of four vehicles shall be taken from the same family and subjected to the tests described in Appendix 1 to Annex XI. The tests may be carried out on vehicles which have completed a maximum of 15000 km with no modifications.
4.7.1.4. The production shall be deemed to conform if at least three vehicles meet the requirements of the tests described in Appendix 1 to Annex XI.