7 Appendix 3b, Regulation (EU) 2017/1151

In forcesince 1 Jan 2019

The assessment of the AES by the type-approval authority shall include at least the following verifications:

(1)

The increase of emissions induced by the AES shall be kept at the lowest possible level:

(a)

The increase of total emissions when using an AES shall be kept at the lowest possible level throughout the normal use and life of the vehicles;

(b)

Whenever a technology or design that would allow for improved emission control is available on the market at the time of the AES preliminary assessment it shall be used with no unjustified modulation

(2)

When used to justify an AES, the risk of sudden and irreparable damage to the ‘propulsion energy converter and the drivetrain’, as defined in Mutual Resolution No. 2 (M.R.2) of the 1958 and 1998 Agreements of UNECE containing Vehicle Propulsion System Definitions [Document ECE/TRANS/WP.19/1121 found in the following webpage: https://ec.europa.eu/docsroom/documents/31821], shall be appropriately demonstrated and documented, including the following information:

(a)

Proof of catastrophic (i.e. sudden and irreparable) engine damage shall be provided by the manufacturer, along with a risk assessment which includes an evaluation of the likelihood of the risk occurring and severity of the possible consequences, including results of tests carried out to this effect;

(b)

When a technology or design is available on the market at the time of the AES application that eliminates or reduces that risk, it shall be used to the largest extent technically possible (i.e. with no unjustified modulation);

(c)

Durability and the long-term protection of the engine or components of the emission control system from wear and malfunctioning shall not be considered an acceptable reason to grant an exemption from the defeat device prohibition.

(3)

An adequate technical description shall document why it is necessary to use an AES for the safe operation of the vehicle:

(a)

Proof of an increased risk to the safe operation of the vehicle should be provided by the manufacturer along with a risk assessment which includes an evaluation of the likelihood of the risk occurring and severity of the possible consequences, including results of tests carried out to this effect;

(b)

When a different technology or design is available on the market at the time of the AES application that would allow for lowering the safety risk, it shall be used to the largest extent technically possible (i.e. with no unjustified modulation).

(4)

An adequate technical description shall document why it is necessary to use an AES during engine start:

(a)

Proof of the need to use an AES during engine start shall be provided by the manufacturer along with a risk assessment which includes an evaluation of the likelihood of the risk occurring and severity of the possible consequences, including results of tests carried out to this effect;

(b)

Where a different technology or design is available on the market at the time of the AES application that would allow for improved emission control upon engine start, it shall be used to the largest extent technically possible.

Changed on 1 Jan 2019

1.1.1. Make: … 1.1.2. Type: … 1.2.1. Make: … 1.2.2. Type: … (state percentage of oil in mixture if lubricant and fuel mixed) VL (if existing) | VH | V representative (only for road load matrix family) 2.2. The assessment of the AES by the type-approval authority shall include at least the following verifications: (1) The increase of emissions induced by the AES shall be kept at the lowest possible level: (a) The increase of total emissions when using an AES shall be kept at the lowest possible level throughout the normal use and life of the vehicles; (b) Whenever a technology or design that would allow for improved emission control is available on the market at the time of the AES preliminary assessment it shall be used with no unjustified modulation (2) When used to justify an AES, the risk of sudden and irreparable damage to the ‘propulsion energy converter and the drivetrain’, as defined in Mutual Resolution No. 2 (M.R.2) of the 1958 and 1998 Agreements of UNECE containing Vehicle bodywork type (variant/version) 2.2. Vehicle bodywork type (variant/version) 2.2. Vehicle bodywork type (variant/version) 2.3. Road load method used (measurement or calculation by road load family) 2.3. Road load method used (measurement or calculation by road load family) 2.3. Road load method used (measurement or calculation by road load matrix family) 2.4. Road load information from the test 2.4. Road load information from the test 2.4. Road load information from the test 2.4.1. Tyres make and type: 2.4.1. Tyres make and type: 2.4.1. Tyres make and type: 2.4.2. Tyre dimensions (front/rear): 2.4.2. Tyre dimensions (front/rear): 2.4.2. Tyre dimensions (front/rear): 2.4.4. Tyre pressure (front/rear) (kPa): 2.4.4. Tyre pressure (front/rear) (kPa): 2.4.4. Tyre pressure (front/rear) (kPa): 2.4.5. Tyre rolling resistance (front/rear) (kg/t): 2.4.5. Tyre rolling resistance (front/rear) (kg/t): 2.4.5. Tyre rolling resistance (front/rear) (kg/t) and RR class (A-G): 2.4.6. Vehicle test mass (kg): 2.4.6. Vehicle test mass (kg): 2.4.6. Vehicle test mass (kg): 2.4.7. Delta Cd.A compared to VH (m2) 2.4.8. Road load coefficient f0, f1, f2 2.4.8. Road load coefficient f0, f1, f2 2.4.8. Road load coefficient f0, f1, f2 2.4.9. Frontal area m2 (0,0000 m2) 2.4.10. Calculation tool information to calculate VH and VL road loadsPropulsion System Definitions [Document ECE/TRANS/WP.19/1121 found in the following webpage: https://ec.europa.eu/docsroom/documents/31821], shall be appropriately demonstrated and documented, including the following information: (a) Proof of catastrophic (i.e. sudden and irreparable) engine damage shall be provided by the manufacturer, along with a risk assessment which includes an evaluation of the likelihood of the risk occurring and severity of the possible consequences, including results of tests carried out to this effect; (b) When a technology or design is available on the market at the time of the AES application that eliminates or reduces that risk, it shall be used to the largest extent technically possible (i.e. with no unjustified modulation); (c) Durability and the long-term protection of the engine or components of the emission control system from wear and malfunctioning shall not be considered an acceptable reason to grant an exemption from the defeat device prohibition. (3) An adequate technical description shall document why it is necessary to use an AES for the safe operation of the vehicle: (a) Proof of an increased risk to the safe operation of the vehicle should be provided by the manufacturer along with a risk assessment which includes an evaluation of the likelihood of the risk occurring and severity of the possible consequences, including results of tests carried out to this effect; (b) When a different technology or design is available on the market at the time of the AES application that would allow for lowering the safety risk, it shall be used to the largest extent technically possible (i.e. with no unjustified modulation). (4) An adequate technical description shall document why it is necessary to use an AES during engine start: (a) Proof of the need to use an AES during engine start shall be provided by the manufacturer along with a risk assessment which includes an evaluation of the likelihood of the risk occurring and severity of the possible consequences, including results of tests carried out to this effect; (b) Where a different technology or design is available on the market at the time of the AES application that would allow for improved emission control upon engine start, it shall be used to the largest extent technically possible.

  1. 1 Jan 2019 – todayin force
  2. 27 Jul 2017 – 1 Jan 2019earlier wording
  3. 1 Jun 2017 – 27 Jul 2017earlier wording