29 Appendix 3, Regulation (EU) 2017/1151

In forcesince 1 Sep 2023

Reserved

Changed on 1 Sep 2023

This Appendix describes the calculation procedures to verify the trip dynamics by determining the excess or absence of dynamics during urban, rural and motorway driving. Δdifference >larger ≥larger or equal %per cent <smaller ≤smaller or equal aacceleration [m/s2] aiacceleration in time step i [m/s2] apospositive acceleration greater than 0,1 m/s2 [m/s2] apos,i,kpositive acceleration greater than 0,1 m/s2 in time step i considering the urban, rural and motorway shares [m/s2] aresacceleration resolution [m/s2] didistance covered in time step i [m] di,kdistance covered in time step i considering the urban, rural and motorway shares [m] Index (i)discrete time step Index (j)discrete time step of positive acceleration datasets Index (k)refers to the respective category (t=total, u=urban, r=rural, m=motorway) Mknumber of samples for urban, rural and motorway shares with positive acceleration greater than 0,1 m/s2 Nktotal number of samples for the urban, rural and motorway shares and the complete trip RPAkrelative positive acceleration for urban, rural and motorway shares [m/s2 or kWs/(kg*km)] tkduration of the urban, rural and motorway shares and the complete trip [s] T4253Hcompound data smoother νvehicle speed [km/h] νiactual vehicle speed in time step i [km/h] νi,kactual vehicle speed in time step i considering the urban, rural and motorway shares [km/h] ν aiactual vehicle speed per acceleration in time step i [m2/s3 or W/kg] ν aposj,kactual vehicle speed per positive acceleration greater than 0,1 m/s2 in time step j considering the urban, rural and motorway shares [m2/s3 or W/kg]. ν aposk9595th percentile of the product of vehicle speed per positive acceleration greater than 0,1 m/s2 for urban, rural and motorway shares [m2/s3 or W/kg] νkaverage vehicle speed for urban, rural and motorway shares [km/h] Dynamic parameters like acceleration, (v · apos) or RPA shall be determined with a speed signal of an accuracy of 0,1 % for all speed values above 3 km/h and a sampling frequency of 1 Hz. This accuracy requirement is generally fulfilled by distance calibrated signals obtained from a wheel (rotational) speed sensor. Otherwise, acceleration shall be determined with an accuracy of 0,01 m/s2 and a sampling frequency of 1 Hz. In this case the separate speed signal, in (v · apos), shall have an accuracy of at least 0,1 km/h. The correct speed trace builds the basis for further calculations and binning as described in paragraph 3.1.2 and 3.1.3. The following calculations shall be performed over the whole time based speed trace (1 Hz resolution) from second 1 to second tt (last second). The distance increment per data sample shall be calculated as follows: d i v i 3,6, i 1 to N t where: diis the distance covered in time step i [m] νiis the actual vehicle speed in time step i [km/h] Ntis the total number of samples The acceleration shall be calculated as follows: aivi 1 vi 1 2 3,6, i 1 to Nt where: aiis the acceleration in time step i [m/s2]. For i = 1: vi-1 0, for i Nt: vi 1 0. The product of vehicle speed per acceleration shall be calculated as follows: v a ivi ai 3,6, i 1 to Nt where: ν aiis the product of the actual vehicle speed per acceleration in time step i [m2/s3 or W/kg]. After the calculation of ai and (v · a)i, the values vi, di, ai and (v · a)i shall be ranked in ascending order of the vehicle speed. All datasets with vi ≤ 60 km/h belong to the ‘urban’ speed bin, all datasets with 60 km/h < vi ≤ 90 km/h belong to the ‘rural’ speed bin and all datasets with vi > 90 km/h belong to the ‘motorway’ speed bin. For N2 category vehicles that are equipped with a device limiting vehicle speed to 90 km/h, all datasets with vi ≤ 60 km/h belong to the ‘urban’ speed bin, all datasets with 60 km/h < vi ≤ 80 km/h belong to the ‘rural’ speed bin and all datasets with vi > 80 km/h belong to the ‘motorway’ speed bin. The number of datasets with acceleration values ai > 0,1 m/s2 shall be greater or equal to 100 in each speed bin. For each speed bin the average vehicle speed vk shall be calculated as follows: vk ivi,kNk, i = 1 to Nk, k= u, r, m Where: Nk is the total number of samples of the urban, rural, and motorway shares. The 95th percentile of the v apos values shall be calculated as follows: The v ai,k values in each speed bin shall be ranked in ascending order for all datasets with ai,k 0,1 ms2 ai,k 0,1 ms2 and the total number of these samples Mk shall be determined. Percentile values are then assigned to the v aposi,k values with ai,k 0,1 ms2 as follows: The lowest v apos value gets the percentile 1/Mk, the second lowest 2/Mk, the third lowest 3/Mk and the highest value MkMk 100 %. v aposk95 is the v aposj,k value, with jMk 95 %. If jMk 95 %. cannot be met, v aposk95 shall be calculated by linear interpolation between consecutive samples j and j+1 with jMk 95 % and j 1Mk 95 %. The relative positive acceleration per speed bin shall be calculated as follows: RPAk j Δt v apos j,k i di,k, j 1 to Mk, i 1 to Nk, k u,r,m where: RPAkis the relative positive acceleration for urban, rural and motorway shares in [m/s2 or kWs/(kg*km)] Δtis a time difference equal to 1 second Mkis the sample number for urban, rural and motorway shares with positive acceleration Nkis the total sample number for urban, rural and motorway shares If vk 74,6kmh and v apos k 95 0,136 v k 14,44 is fulfilled, the trip is invalid. If vk 74,6kmh and v aposk95 0,0742vk 18,966 is fulfilled, the trip is invalid. Upon the request of the manufacturer, and only for those N1 or N2 vehicles where the vehicle power-to-mass ratio is less than or equal to 44 W/kg then: If vk74,6 kmh and vapos k _950,136 v k 14,44 is fulfilled, the trip is invalid. If vk74,6 kmh and vapos k _950,097 v k 31,635 is fulfilled, the trip is invalid. To calculate the power-to-mass ratio, the following values shall be used: the mass which corresponds to the actual test mass of the vehicle including the drivers and the PEMS equipment (kg); the maximum rated engine power as declared by the manufacturer (W). If vk94,05 kmh and RPAk0,0016vk0,1755 is fulfilled, the trip is invalid. If vk94,05 kmh and RPAk < 0,025 is fulfilled, the trip is invalid.Reserved

  1. 1 Sep 2023 – todayin force
  2. 1 Jan 2019 – 1 Sep 2023earlier wording
  3. 27 Jul 2017 – 1 Jan 2019earlier wording
  4. 1 Jun 2017 – 27 Jul 2017earlier wording