[The values quoted in the specifications are ‘true values’. In establishment of their limit values the terms of ISO 4259 Petroleum products - Determination and application of precision data in relation to methods of test have been applied and in fixing a minimum value, a minimum difference of 2R above zero has been taken into account; in fixing a maximum and minimum value, the minimum difference is 4R (R = reproducibility). Notwithstanding this measure, which is necessary for technical reasons, the manufacturer of fuels shall nevertheless aim at a zero value where the stipulated maximum value is 2R and at the mean value in the case of quotations of maximum and minimum limits. Should it be necessary to clarify whether a fuel meets the requirements of the specifications, the terms of ISO 4259 shall be applied.] [A correction factor of 0,2 for MON and RON shall be subtracted for the calculation of the final result in accordance with EN 228:2008.] [A correction factor of 0,2 for MON and RON shall be subtracted for the calculation of the final result in accordance with EN 228:2008.] [The fuel may contain oxidation inhibitors and metal deactivators normally used to stabilise refinery gasoline streams, but detergent/dispersive additives and solvent oils shall not be added.] [Ethanol is the only oxygenate that shall be intentionally added to the The specification for the reference fuel. The Ethanol used shall conform to EN 15376.] [The actual sulphur content of the fuel used for the Type 1 test shall be reported.] [There shall be no intentional addition of compounds containing phosphorus, iron, manganese, or lead to this reference fuel.] [Ethanol is the only oxygenate that shall be intentionally added to the reference fuel. The Ethanol used shall conform to EN 15376.]
Parameter | Unit | Limits | Test method
Minimum | Maximum
Research octane number, RON | | 95,0 | 98,0 | EN ISO 5164
Motor octane number, MON | | 85,0 | 89,0 | EN ISO 5163
Density at 15 C | kg/m3 | 743,0 | 756,0 | EN ISO 12185
Vapour pressure (DVPE) | kPa | 56,0 | 60,0 | EN 13016-1
Water content | % v/v | | 0,05 | EN 12937
Appearance at – 7 C | | Clear and bright |
Distillation: | | | |
— evaporated at 70 C
% v/v | 34,0 | 46,0 | EN ISO 3405
— evaporated at 100 C
% v/v | 54,0 | 62,0 | EN ISO 3405
— evaporated at 150 C
% v/v | 86,0 | 94,0 | EN ISO 3405
— final boiling point
°C | 170 | 195 | EN ISO 3405
Residue | % v/v | — | 2,0 | EN ISO 3405
Hydrocarbon analysis: | | | |
— olefins
% v/v | 6,0 | 13,0 | EN 22854
— aromatics
% v/v | 25,0 | 32,0 | EN 22854
— benzene
% v/v | — | 1,00 |
EN 22854
EN 238
— saturates
% v/v | report | EN 22854
Carbon/hydrogen ratio | | report |
Carbon/oxygen ratio | | report |
Induction Period | minutes | 480 | — | EN ISO 7536
Oxygen content | % m/m | 3,3 | 3,7 | EN 22854
Solvent washed gum
(Existent gum content)
mg/100 ml | — | 4 | EN ISO 6246
Sulphur content | mg/kg | — | 10 |
EN ISO 20846
EN ISO 20884
Copper corrosion 3 hrs, 50 C | | — | class 1 | EN ISO 2160
Lead content | mg/l | — | 5 | EN 237
Phosphorus content | mg/l | — | 1,3 | ASTM D 3231
Ethanol | % v/v | 9,0 | 10,0 | EN 22854
(2) Equivalent EN/ISO methods will be adopted when issued for properties listed above.
[The values quoted in the specifications are ‘true values’. In establishment of their limit values the terms of ISO 4259 Petroleum products — Determination and application of precision data in relation to methods of test have been applied and in fixing a minimum value, a minimum difference of 2R above zero has been taken into account; in fixing a maximum and minimum value, the minimum difference is 4R (R = reproducibility). Notwithstanding this measure, which is necessary for technical reasons, the manufacturer of fuels shall nevertheless aim at a zero value where the stipulated maximum value is 2R and at the mean value in the case of quotations of maximum and minimum limits. Should it be necessary to clarify whether a fuel meets the requirements of the specifications, the terms of ISO 4259 shall be applied.] [In cases of dispute, the procedures for resolving the dispute and interpretation of the results based on test method precision, described in EN ISO 4259 shall be to be used.] [In cases of national dispute concerning sulphur content, either EN ISO 20846 or EN ISO 20884 shall be called up similar to the reference in the national annex of EN 228.] [The actual sulphur content of the fuel used for the Type 1 test shall be reported.] [Ethanol to meet specification of EN 15376 is the only oxygenate that shall be intentionally added to this reference fuel.] [The unleaded petrol content can be determined as 100 minus the sum of the percentage content of water and alcohols] [There shall be no intentional addition of compounds containing phosphorus, iron, manganese, or lead to this reference fuel.]
Parameter | Unit | Limits | Test method
Minimum | Maximum
Research octane number, RON | | 95 | — | EN ISO 5164
Motor octane number, MON | | 85 | — | EN ISO 5163
Density at 15 C | kg/m3 | Report | ISO 3675
Vapour pressure | kPa | 40 | 60 | EN ISO 13016-1 (DVPE)
Sulphur content | mg/kg | — | 10 | EN ISO 20846 EN ISO 20884
Oxidation stability | minutes | 360 | | EN ISO 7536
Existent gum content (solvent washed) | mg/100ml | — | 5 | EN-ISO 6246
Appearance This shall be determined at ambient temperature or 15 C whichever is higher. | | Clear and bright, visibly free of suspended or precipitated contaminants | Visual inspection
Ethanol and higher alcohols | % (V/V) | 83 | 85 |
EN 1601
EN 13132
EN 14517
Higher alcohols (C3-C8) | % (V/V) | — | 2 |
Methanol | % (V/V) | | 0,5 |
Petrol | % (V/V) | Balance | EN 228
Phosphorus | mg/l | 0,3 | ASTM D 3231
Water content | % (V/V) | | 0,3 | ASTM E 1064
Inorganic chloride content | mg/l | | 1 | ISO 6227
pHe | | 6,5 | 9 | ASTM D 6423
Copper strip corrosion (3h at 50 C) | Rating | Class 1 | | EN ISO 2160
Acidity, (as acetic acid CH3COOH) | % (m/m) | — | 0,005 | ASTM D 1613
(mg/l) | — | 40
Carbon/hydrogen ratio | | report |
Carbon/oxygen ration | | report |
[This method may not accurately determine the presence of corrosive materials if the sample contains corrosion inhibitors or other chemicals which diminish the corrosivity of the sample to the copper strip. Therefore, the addition of such compounds for the sole purpose of biasing the test method is prohibited.]
Parameter | Unit | Fuel A | Fuel B | Test method
Composition: | | | | ISO 7941
C3-content | % vol | 30 ± 2 | 85 ± 2 |
C4-content | % vol | Balance | Balance |
< C3, > C4 | % vol | Maximum 2 | Maximum 2 |
Olefins | % vol | Maximum 12 | Maximum 15 |
Evaporation residue | mg/kg | Maximum 50 | Maximum 50 | prEN 15470
Water at 0 C | | Free | Free | prEN 15469
Total sulphur content | mg/kg | Maximum 10 | Maximum 10 | ASTM 6667
Hydrogen sulphide | | None | None | ISO 8819
Copper strip corrosion | Rating | Class 1 | Class 1 | ISO 6251
Odour | | Characteristic | Characteristic |
Motor octane number | | Minimum 89 | Minimum 89 | EN 589 those set out in Annex B
[Inerts (different from N2) + C2 + C2+.] [Value to be determined at 293,2 K (20 C) and 101,3 kPa.] [Value to be determined at 273,2 K (0 C) and 101,3 kPa.] [Inerts (different from N2) + C2; + C2+.] [Value to be determined at 293,2 K (20 C) and 101,3 kPa.] [Value to be determined at 273,2 K (0 C) and 101,3 kPa.]
Characteristics | Units | Basis | Limits | Test method
minimum | maximum
Reference fuel G20 | | | | |
Composition: | | | | |
Methane | % mole | 100 | 99 | 100 | ISO 6974
Balance | % mole | — | — | 1 | ISO 6974
N2 | % mole | | | | ISO 6974
Sulphur content | mg/m3 | — | — | 10 | ISO 6326-5
Wobbe Index (net) | MJ/m3 | 48,2 | 47,2 | 49,2 |
Reference fuel G25 | | | | |
Composition: | | | | |
Methane | % mole | 86 | 84 | 88 | ISO 6974
Balance | % mole | — | — | 1 | ISO 6974
N2 | % mole | 14 | 12 | 16 | ISO 6974
Sulphur content | mg/m3 | — | — | 10 | ISO 6326-5
Wobbe Index (net) | MJ/m3 | 39,4 | 38,2 | 40,6 |
[Not to be condensed.] [Combined water, oxygen, nitrogen and argon: 1,900 μmol/mol.] [Combined water, oxygen, nitrogen and argon: 1,900 μmol/mol.] [Combined water, oxygen, nitrogen and argon: 1,900 μmol/mol.] [Combined water, oxygen, nitrogen and argon: 1,900 μmol/mol.] [The hydrogen shall not contain dust, sand, dirt, gums, oils, or other substances in an amount sufficient to damage the fuelling station equipment or the vehicle (engine) being fuelled.]
Characteristics | Units | Limits | Test method
minimum | maximum
Hydrogen purity | % mole | 98 | 100 | ISO 14687-1
Total hydrocarbon | μmol/mol | 0 | 100 | ISO 14687-1
Water | μmol/mol | 0 | | ISO 14687-1
Oxygen | μmol/mol | 0 | | ISO 14687-1
Argon | μmol/mol | 0 | | ISO 14687-1
Nitrogen | μmol/mol | 0 | | ISO 14687-1
CO | μmol/mol | 0 | 1 | ISO 14687-1
Sulphur | μmol/mol | 0 | 2 | ISO 14687-1
Permanent particulates | | | | ISO 14687-1
[The values quoted in the specifications are ‘true values’. In establishment of their limit values the terms of ISO 4259 Petroleum products – Determination and application of precision data in relation to methods of test have been applied and in fixing a minimum value, a minimum difference of 2R above zero has been taken into account; in fixing a maximum and minimum value, the minimum difference is 4R (R = reproducibility). Notwithstanding this measure, which is necessary for technical reasons, the manufacturer of fuels shall nevertheless aim at a zero value where the stipulated maximum value is 2R and at the mean value in the case of quotations of maximum and minimum limits. Should it be necessary to clarify whether a fuel meets the requirements of the specifications, the terms of ISO 4259 shall be applied.] [The range for cetane number is not in accordance with the requirements of a minimum range of 4R. However, in the case of a dispute between fuel supplier and fuel user, the terms of ISO 4259 may be used to resolve such disputes provided replicate measurements, of sufficient number to archive the necessary precision, are made in preference to single determinations.] [Even though oxidation stability is controlled, it is likely that shelf life will be limited. Advice shall be sought from the supplier as to storage conditions and life.] [FAME content to meet the specification of EN 14214.]
Parameter | Unit | Limits | Test method
Minimum | Maximum
Cetane Index | | 46,0 | | EN ISO 4264
Cetane number | | 52,0 | 56,0 | EN ISO 5165
Density at 15 C | kg/m3 | 833,0 | 837,0 | EN ISO 12185
Distillation: | | | |
— 50 % point
°C | 245,0 | — | EN ISO 3405
— 95 % point
°C | 345,0 | 360,0 | EN ISO 3405
— final boiling point
°C | — | 370,0 | EN ISO 3405
Flash point | °C | 55 | — | EN ISO 2719
Cloud point | °C | — | – 10 | EN 23015
Viscosity at 40 C | mm2/s | 2,30 | 3,30 | EN ISO 3104
Polycyclic aromatic hydrocarbons | % m/m | 2,0 | 4,0 | EN 12916
Sulphur content | mg/kg | — | 10,0 |
EN ISO 20846
EN ISO 20884
Copper corrosion 3 hrs, 50 C | | — | Class 1 | EN ISO 2160
Conradson carbon residue (10 % DR) | % m/m | — | 0,20 | EN ISO 10370
Ash content | % m/m | — | 0,010 | EN ISO 6245
Total contamination | mg/kg | — | 24 | EN 12662
Water content | mg/kg | — | 200 | EN ISO 12937
Acid number | mg KOH/g | — | 0,10 | EN ISO 6618
Lubricity (HFRR wear scan diameter at 60 C) | μm | — | 400 | EN ISO 12156
Oxidation stability at 110 C | h | 20,0 | | EN 15751
FAME | % v/v | 6,0 | 7,0 | EN 14078
For the constituents that are additive, such as total hydrocarbons and total sulfur compounds, the sum of the constituents are to be less than or equal to the acceptable limit.
[The hydrogen fuel index is determined by subtracting the ‘total non-hydrogen gases’ in this table, expressed in mole per cent, from 100 mole per cent.] [Total hydrocarbons include oxygenated organic species. Total hydrocarbons shall be measured on a carbon basis (μmolC/mol). Total hydrocarbons may exceed 2 μmol/mol due only to the presence of methane, in which case the summation of methane, nitrogen and argon shall not exceed 100 μmol/mol.] [As a minimum, total sulphur compounds include H2S, COS, CS2 and mercaptans, which are typically found in natural gas.] [Total halogenated compounds include, for example, hydrogen bromide (HBr), hydrogen chloride (HCl), chlorine (Cl2), and organic halides (R-X).] [Test method shall be documented.]
Characteristics | Units | Limits | Test Method
minimum | maximum
Hydrogen fuel index | % mole | 99,97 | |
Total non-hydrogen gases | μmol/mol | | 300 |
Maximum concentration of individual contaminants
Water (H2O) | μmol/mol | | 5 |
Total hydrocarbons (Methane basis) | μmol/mol | | 2 |
Oxygen (O2) | μmol/mol | | 5 |
Helium (He) | μmol/mol | | 300 |
Total Nitrogen (N2) and Argon (Ar) | μmol/mol | | 100 |
Carbon dioxide (CO2) | μmol/mol | | 2 |
Carbon monoxide (CO) | μmol/mol | | 0,2 |
Total sulfur compounds (H2S basis) | μmol/mol | | 0,004 |
Formaldehyde (HCHO) | μmol/mol | | 0,01 |
Formic acid (HCOOH) | μmol/mol | | 0,2 |
Ammonia (NH3) | μmol/mol | | 0,1 |
Total halogenated compounds
(Halogenate ion basis)
μmol/mol | | 0,05 |B3 to UN Regulation No 154.