This appendix describes the calculation procedures to verify the trip dynamics by determining the excess or absence of dynamics during an RDE trip.
a | — | acceleration [m/s2]
ai | — | Acceleration in time step i [m/s2]
apos | — | positive acceleration greater than 0,1 m/s2 [m/s2]
apos,i,k | — | positive acceleration greater than 0,1 m/s2 in time step i considering the urban, rural and motorway shares [m/s2]
ares | — | acceleration resolution [m/s2]
di | — | distance covered in time step i [m]
di,k | — | distance covered in time step i considering the urban, rural and motorway shares [m]
Index (i) | — | discrete time step
Index (j) | — | discrete time step of positive acceleration datasets
Index (k) | — | refers to the respective category (t=total, u=urban, r=rural, m=motorway)
Mk | — | number of samples for urban, rural and motorway shares with positive acceleration greater than 0,1 m/s2
Nk | — | total number of samples for the urban, rural and motorway shares and the complete trip
RPAk | — | relative positive acceleration for urban, rural and motorway shares [m/s2 or kWs/(kg*km)]
tk | — | duration of the urban, rural and motorway shares and the complete trip [s]
v | — | vehicle speed [km/h]
vi | — | actual vehicle speed in time step i [km/h]
vi,k | — | actual vehicle speed in time step i considering the urban, rural and motorway shares [km/h]
(v × a)i | — | actual vehicle speed per acceleration in time step i [m2/s3 or W/kg]
(v × a)j,k | — | actual vehicle speed per positive acceleration greater than 0,1 m/s2 in time step j considering the urban, rural and motorway shares [m2/s3 or W/kg].
(v × apos)k-[95] | — | 95th percentile of the product of vehicle speed per positive acceleration greater than 0,1 m/s2 for urban, rural and motorway shares [m2/s3 or W/kg]
vk | — | average vehicle speed for urban, rural and motorway shares [km/h]
Dynamic parameters, such as acceleration, (v × aapos) or RPA, shall be determined with a speed signal of an accuracy of 0,1 % for all speed values above 3 km/h and a sampling frequency of 1 Hz. Otherwise, acceleration shall be determined with an accuracy of 0,01 m/s2 and a sampling frequency of 1 Hz. In this case, a separate speed signal is required for (v × aapos) and shall have an accuracy of at least 0,1 km/h. The speed trace shall form the basis for further calculations and binning as described in paragraphs 3.1.2. and 3.1.3.
The following calculations shall be performed over the whole time based speed trace from the beginning to the end of the test data.
The distance increment per data sample shall be calculated as follows:
di
vi
3,6 i 1 to Nt
where:
di | | is the distance covered in time step i [m]
νi | | is the actual vehicle speed in time step i [km/h]
Nt | | is the total number of samples
The acceleration shall be calculated as follows:
ai
vi 1 vi 1
2 3,6 i 1 to Nt
where:
ai | |
is the acceleration in time step i [m/s2].
For i = 1: vi–1 = 0,
for i = Nt: vi+ 1 =0.
The product of vehicle speed per acceleration shall be calculated as follows:
v × aivi × ai
3,6
where:
(v × a)i | | is the product of the actual vehicle speed per acceleration in time step i [m2/s3 or W/kg].
After the calculation of ai and (v × a)i, the values vi, di, ai and (v × a)i shall be ranked in ascending order of the vehicle speed.
All datasets with (vi ≤ 60 km/h) belong to the ‘urban’ speed bin, all datasets with (60 km/h < vi ≤ 90 km/h) belong to the ‘rural’ speed bin and all datasets with (vi > 90 km/h) belong to the ‘motorway’ speed bin.
For N2 category vehicles that are equipped with a device limiting vehicle speed to 90 km/h, all datasets with vi ≤ 60 km/h belong to the ‘urban’ speed bin, all datasets with 60 km/h < vi ≤ 80 km/h belong to the ‘rural’ speed bin and all datasets with vi > 80 km/h belong to the ‘motorway’ speed bin.
The number of datasets with acceleration values ai > 0,1 m/s2 shall be greater than or equal to 100 in each speed bin.
For each speed bin the average vehicle speed (
v
shall be calculated as follows:
v
k1
Nk
i
vi,k i 1 to Nk,k u,r,m
where:
Nk | | is the total number of samples of the urban, rural, and motorway shares.
The 95th percentile of the (v × apos) values shall be calculated as follows:
The (v × apos)i,k values in each speed bin shall be ranked in ascending order for all datasets with ai,k > 0,1m/s2 and the total number of these samples Mk shall be determined.
Percentile values are then assigned to the (v × apos)i,k values with ai,k > 0,1 m/s2 as follows:
The lowest (v × apos)value gets the percentile 1/Mk, the second lowest 2/Mk, the third lowest 3/Mk and the highest value (Mk/Mk = 100 %.)
(v × apos)k-[95] is the (v × apos)j,k value, with j/Mk = 95 %. If j/Mk = 95 % cannot be met, (v × apos)k-[95] shall be calculated by linear interpolation between consecutive samples j and j+1 with j/Mk < 95 % and (j+1)/Mk > 95 %.
The relative positive acceleration per speed bin shall be calculated as follows:
RPAk
j
v aposj,k
i
di,k
, j 1 to Mk, i 1 to Nk, k u, r, m
where:
RPAk | | is the relative positive acceleration for urban, rural and motorway shares in [m/s2 or kWs/(kg*km)]
Mk | | is the sample number for urban, rural and motorway shares with positive acceleration
Nk | | is the total sample number for urban, rural and motorway shares
If
v
k ≤ 74,6 km/h and
(v × apos)k-[95] > (0,136 ×
v
k + 14,44)
is fulfilled, the trip is invalid.
If
v
k > 74,6 km/h and
(v × apos)k-[95] > (0,0742 ×
v
k + 18,966)
is fulfilled, the trip is invalid.
Upon the request of the manufacturer, and only for those N1 or N2 vehicles where the vehicle power-to-test mass ratio is less than or equal to 44 W/kg then:
If
v
k ≤ 74,6 km/h and
(v × apos)k-[95] > (0,136 ×
v
k + 14,44)
is fulfilled, the trip is invalid.
If
v
k > 74,6 km/h and
(v × apos)k-[95] > (– 0,097 ×
v
k + 31,635)
is fulfilled, the trip is invalid.
If
v
k ≤ 94,05 km/h and
RPAk < (– 0,0016
v
k + 0,1755)
is fulfilled, the trip is invalid.
If
v
k > 94,05 km/h and RPAk < 0,025 is fulfilled, the trip is invalid.