A family of electric machine systems or IEPCs is characterised by design and performance parameters. These shall be common to all members within the family. The component manufacturer may decide which electric machine systems or IEPCs belong to a family, as long as the membership criteria listed in this Appendix are respected. The related family shall be approved by the Approval Authority. The component manufacturer shall provide to the Approval Authority the appropriate information relating to the members of the family.
In some cases there may be interaction between parameters. This shall be taken into consideration to ensure that electric machine systems or IEPCs with similar characteristics are included within the same family. These cases shall be identified by the component manufacturer and notified to the Approval Authority. It shall then be taken into account as a criterion for creating a new family of electric machine systems or IEPCs.
In the case of devices or features, which are not listed in paragraph 1.4 and which have a strong influence on the level of performance and/or the electric power consumption, the respective devices or features shall be identified by the component manufacturer on the basis of good engineering practice, and shall be notified to the Approval Authority. It shall then be taken into account as a criterion for creating a new family of electric machine systems or IEPCs.
The family concept defines criteria and parameters enabling the component manufacturer to group electric machine systems or IEPCs into families with similar or equal data relevant for CO2-emissions or energy consumption.
The Approval Authority may conclude that the performance parameters and the electric power consumption of the family of electric machine systems or IEPCs can best be characterised by additional testing. In this case, the component manufacturer shall submit the appropriate information to determine the electric machine system or IEPC within the family likely to best represent the family. The Approval Authority may based on this information also conclude that it is required for the component manufacturer to create a new family of electric machine systems or IEPCs consisting of less members in order to be more representative.
If members within a family incorporate other features which may be considered to affect the performance parameters and/or the electric power consumption, these features shall also be identified and taken into account in the selection of the parent.
In addition to the parameters listed below, the component manufacturer may introduce additional criteria allowing the definition of families of more restricted size. These parameters are not necessarily parameters that have an influence on the level of performance and/or the electric power consumption.
1.5.1. The following criteria shall in principal be the same to all members within a family of electric machine systems or IEPCs:
Electric Machine: Rotor, Stator, Windings in dimensions, design, material, etc.
Inverter: Power Modules, Conductive bars in dimensions, design, material, etc.
Internal cooling system: layout, dimension and material of cooling fins, ribs, and pins
Internal fans: layout and dimension
Inverter Software: Basic calibration which consists of temperature models (electric machine and inverter), derating limits, torque path (transfer of command torque to phase current), flux calibration, current control, voltage modulation, sensor specific calibration (only allowed if sensor is changed)
Gear related parameters (only for IEPCs): in accordance with definitions set out in Annex VI.
Changes to the components as mentioned at (a) through (f) are only acceptable as long as sound engineering rationale can be provided to prove that the respective change does not negatively affect the performance parameters and/or the electric power consumption.
1.5.2. The following criteria shall be common to all members within a family of electric machine systems or IEPCs. The application of a specific range to the parameters listed below is permitted after approval of the Approval Authority:
Output shaft interface: any changes allowed;
End shields:
For the internal design it must be checked if passive cooling elements or air flow at the inner side of the end shields are affected by changes.
For the external design screws, suspension points, flange design have no influence on performance if no passive cooling elements are removed or changed;
Bearings: Changes allowed as long as number and type of bearings remain the same;
Shaft: Changes allowed as long as active or passive cooling is not affected;
High voltage connection: Changes regarding position or type of the high voltage connection allowed;
Housing: Changes of the housing or number, type and position of screws or mounting points allowed as long as no passive cooling elements are removed or changed;
Sensor: Changes allowed, if certified performance is not changed;
Inverter housing: Changes of the housing or number, type and position of screws or mounting points allowed as long as no passive cooling elements are removed or changed or the inner layout of the electric active parts is not changed;
Inverter high voltage connection: Changes regarding position or type of the high voltage connection allowed as long as the layout or position of the active parts or cooling elements (active/passive) is not changed;
Inverter software: All software changes which do not change the basic calibration of the electric machine (definition see above) are allowed. Notwithstanding the previous provisions, limitations of output power are allowed for members within a family of electric machine systems or IEPCs;
Inverter sensor: Changes allowed, if certified performance is not changed;
Oil viscosity: for all oils that are specified for the factory fill, the kinematic viscosity at the same temperature shall be less or equal to 110 % of the kinematic viscosity of the oil used for component certification as documented in the respective information document (within the specified tolerance band for KV100);
Maximum torque curve
The torque values at each rotational speed of the maximum torque curve of the parent determined in accordance with paragraph 4.2.2.4 of this Annex shall be equal or higher than for all other members within the same family at the same rotational speed over the whole rotational speed range. Torque values of other members within the same family within a tolerance of +40 Nm or +4 %, whatever is larger, above the maximum torque of the parent at a specific rotational speed are considered as equal;
Minimum torque curve
The torque values at each rotational speed of the minimum torque curve of the parent determined in accordance with paragraph 4.2.2.4 of this Annex shall be equal or lower than for all other members within the same family at the same rotational speed over the whole rotational speed range. Torque values of other members within the same family within a tolerance of -40 Nm or -4 %, whatever is larger, below the minimum torque of the parent at a specific rotational speed are considered as equal;
Minimum number of points in the EPMC map:
All members within the same family shall have a minimum coverage of 60 % of the points (rounded up to the next whole number) of the EPMC map (i.e. where the EPMC map of the parent is applied to other members) located within the boundaries of their respective maximum and minimum torque curves determined in accordance with paragraph 4.2.2.4 of this Annex.
The parent of one family of electric machine systems or IEPCs shall be member with the highest overall maximum torque determined in accordance with paragraph 4.2.2 of this Annex.