27 Appendix 3, Regulation (EU) 2022/1379

In forcesince 5 Jul 2022

Information document no.:

Issue:

Date of issue:

Date of Amendment:

pursuant to …

…

0.

GENERAL

0.1. Name and address of manufacturer

0.2. Make (trade name of manufacturer):

0.3. IEPC type:

0.4. IEPC family:

0.5. IEPC type as separate technical unit / IEPC family as separate technical unit

0.6. Commercial name(s) (if available):

0.7. Means of identification of model, if marked on the IEPC:

0.8. In the case of components and separate technical units, location and method of affixing of the EC approval mark:

0.9. Name(s) and address(es) of assembly plant(s):

0.10. Name and address of the manufacturer's representative:

|Parent IEPC | |Family members

|or IEPC type | |

| | | #1 | | #2 | | #3 | |

1.

General

1.1. Test voltage(s): V

1.2. Basic motor rotational speed: 1/min

1.3. Motor output shaft maximum speed: 1/min

1.4. (or by default) reducer/gearbox outlet shaft speed: 1/min

1.5. Maximum power speed: 1/min

1.6. Maximum power: kW

1.7. Maximum torque speed: 1/min

1.8. Maximum torque: Nm

1.9. Maximum 30 minutes power: kW

1.10. Number of electric machines:

2.

Electric machine (for each electric machine):

2.1. Electric machine ID:

2.2. Working principle

2.2.1. Direct current (DC)/alternating current (AC):

2.2.2. Number of phases:

2.2.3. Excitation / separate / series / compound:

2.2.4. Synchron / asynchron:

2.2.5. Rotor coiled / with permanent magnets / with housing:

2.2.6. Number of poles of the motor:

2.3. Rotational inertia: kgm2

3.

Power controller (for each power controller):

3.1. Corresponding electric machine ID:

3.2. Make:

3.3. Type:

3.4. Working principle:

3.5. Control principle: vectorial / open loop / closed / other (t.b.s.):

3.6. Maximum effective current supplied to the motor: A

3.7. For maximum duration of: s

3.8. DC voltage range used (from / to): V

3.9. DC/DC converter is part of the electric machine system in accordance with paragraph 4.1 of this Annex (yes/no):

4.

Cooling system

4.1. Motor (liquid / air / other t.b.s.):

4.2. Controller (liquid / air / other t.b.s.):

4.3. Description of the system:

4.4. Principle drawing(s):

4.5. Temperature boundary limits (min/max): K

4.6. At reference position:

4.7. Flow rates (min/max): g/min or ltr/min

5.

Gearbox

5.1. Gear ratio, gearscheme and powerflow:

5.2. Center distance for countershaft transmissions:

5.3. Type of bearings at corresponding positions (if fitted):

5.4. Type of shift elements (tooth clutches, including synchronisers or friction clutches) at corresponding positions (where fitted):

5.5. Total number of forward gears:

5.6. Number of tooth shift clutches:

5.7. Number of synchronisers:

5.8. Number of friction clutch plates (except for single dry clutch with 1 or 2 plates):

5.9. Outer diameter of friction clutch plates (except for single dry clutch with 1 or 2 plates):

5.10. Surface roughness of the teeth (incl. drawings):

5.11. Number of dynamic shaft seals:

5.12. Oil flow for lubrication and cooling per transmission input shaft revolution

5.13. Oil viscosity at 100 C (± 10 %):

5.14. System pressure for hydraulically controlled gearboxes:

5.15. Specified oil level in reference to central axis and in accordance with the drawing specification (based on average value between lower and upper tolerance) in static or running condition. The oil level is considered as equal if all rotating transmission parts (except for the oil pump and the drive thereof) are located above the specified oil level:

5.16. Specified oil level (± 1mm):

5.17. Gear ratios [-] and maximum input torque [Nm], maximum input power (kW) and maximum input speed [rpm] (for each forward gear):

6.

Differential

6.1. Gear ratio:

6.2. Principle technical specifications:

6.3. Principle drawings:

6.4. Oil volume:

6.5. Oil level:

6.6. Oil specification:

6.7. Bearing type (type, quantity, inner diameter, outer diameter, width and drawing):

6.8. Seal type (main diameter, lip quantity):

6.9. Wheel ends (drawing):

6.9.1. Bearing type (type, quantity, inner diameter, outer diameter, width and drawing):

6.9.2. Seal type (main diameter, lip quantity):

6.9.3. Grease type:

6.10. Number of planetary / spur gears for differential:

6.11. Smallest width of planetary/ spur gears for differential:

7.

Documented values from component testing

7.1. Efficiency figures for CoP (*):

7.2. Cooling system (declaration for each cooling circuit):

7.2.1. maximum coolant mass flow or volume flow or maximum inlet pressure:

7.2.2. maximum coolant temperatures:

7.2.3. maximum available cooling power:

7.2.4. Recorded average values for each test run

7.2.4.1. coolant volume flow or mass flow:

7.2.4.2. coolant temperature at the inlet of the cooling circuit:

7.2.4.3. coolant temperature at the inlet and outlet of the test bed heat exchanger on the side of the IEPC:

No.: | Description: | Date of issue:

1 | Information on IEPC test conditions … |

2 | … |

8.

Information on test conditions (if applicable)

8.1. Maximum tested input speed [rpm]

8.2. Maximum tested input torque [Nm]