The following steps shall be performed to generate the input data for the electric machine system based on standard values:
Step 1: UN Regulation No. 85 shall be applied for this Appendix unless stated otherwise.
Step 2: The maximum torque values as a function of the rotational speed shall be determined from the data generated in accordance with paragraph 5.3.1.4 of UN Regulation No. 85. The data shall be extended in accordance with point 4.3.2 of this Annex.
Step 3: The minimum torque values as a function of the rotational speed shall be determined by multiplying the torque values from Step 2 above by minus one.
Step 4: The maximum 30 minutes continuous torque and the corresponding rotational speed shall be determined from the data generated in accordance with paragraph 5.3.2.3 of UN Regulation No. 85 as average values over the 30 minutes period. In case no value for the maximum 30 minutes continuous torque in accordance with Regulation No. 85 can be determined or the value determined is 0 Nm, the applicable input data shall be set to 0 Nm and the corresponding rotational speed shall be set to the rated speed determined from the data generated in accordance with Step 2 above.
Step 5: The overload characteristics shall be determined from the data generated in accordance with Step 2 above. The overload torque and the corresponding rotational speed shall be calculated as average values over the speed range where the power is equal or greater than 90 % of the maximum power. The overload duration t0_maxP shall be defined by the whole duration of the test run performed in accordance with Step 2 above multiplied by a factor of 0,25.
Step 6: The electric power consumption map shall be determined in accordance with the following provisions:
A normalised power loss map shall be calculated as a function of normalised speed and torque values in accordance with the following equation:
Ploss,normTnorm,i, ωnorm,j
3m,n 0
kmnTnorm,imωnorm,jn
where:
Ploss,normnormalised loss power [–]
Tnorm,inormalised torque for all gridpoints defined in accordance with subpoint (b)(ii) below [–]
ωnorm,jnormalised speed for all gridpoints defined in accordance with subpoint (b)(i) below [–]
kloss coefficient [–]
mindex regarding torque dependent losses running from 0 to 3 [–]
nindex regarding speed dependent losses running from 0 to 3 [–]
The normalised speed and torque values to be used for the equation in subpoint (a) above defining the grid points of the normalised loss map shall be:
normalised speed: 0,02, 0,20, 0,40, 0,60, 0,80, 1,00, 1,20, 1,40, 1,60, 1,80, 2,00, 2,20, 2,40, 2,60, 2,80, 3,00, 3,20, 3,40, 3,60, 3,80, 4,00 Where the highest rotational speed determined from the data generated in accordance with Step 2 above is located higher than a normalised speed value of 4,00, additional values of normalised speed with an increment of 0,2 shall be added to the existing list in order to cover the required speed range.
normalised torque: – 1,00, – 0,95, – 0,90, – 0,85, – 0,80, – 0,75, – 0,70, – 0,65, – 0,60, – 0,55, – 0,50, – 0,45, – 0,40, – 0,35, – 0,30, – 0,25, – 0,20, – 0,15, – 0,10, – 0,05, – 0,01, 0,01, 0,05, 0,10, 0,15, 0,20, 0,25, 0,30, 0,35, 0,40, 0,45, 0,50, 0,55, 0,60, 0,65, 0,70, 0,75, 0,80, 0,85, 0,90, 0,95, 1,00
The loss coefficient k to be used for the equation in subpoint (a) above shall be defined depending on the indices m and n in accordance with the following tables:
In the case of an electric machine of the type PSM:
n
0 | 1 | 2 | 3
m | 3 | 0 | 0 | 0 | 0
2 | 0,018 | 0,001 | 0,03 | 0
1 | 0,0067 | 0 | 0 | 0
0 | 0 | 0,005 | 0,0025 | 0,003
In the case of an electric machine of all other types except PSM:
n
0 | 1 | 2 | 3
m | 3 | 0 | 0 | 0 | 0
2 | 0,1 | 0,03 | 0,03 | 0
1 | 0,01 | 0 | 0,001 | 0
0 | 0,003 | 0 | 0,001 | 0,001
From the normalised power loss map determined in accordance with subpoints (a) to (c) above, the efficiency shall be calculated in accordance with the following provisions:
The grid points for the normalised speed shall be: 0,02, 0,20, 0,40, 0,60, 0,80, 1,00, 1,20, 1,40, 1,60, 1,80, 2,00, 2,20, 2,40, 2,60, 2,80, 3,00, 3,20, 3,40, 3,60, 3,80, 4,00
Where the highest rotational speed determined from the data generated in accordance with Step 2 above is located higher than a normalised speed value of 4,00, additional values of normalised speed with an increment of 0,2 shall be added to the existing list in order to cover the required speed range.
The grid points for the normalised torque shall be: – 1,00, – 0,95, – 0,90, – 0,85, – 0,80, – 0,75, – 0,70, – 0,65, – 0,60, – 0,55, – 0,50, – 0,45, – 0,40, – 0,35, – 0,30, – 0,25, – 0,20, – 0,15, – 0,10, – 0,05, – 0,01, 0,01, 0,05, 0,10, 0,15, 0,20, 0,25, 0,30, 0,35, 0,40, 0,45, 0,50, 0,55, 0,60, 0,65, 0,70, 0,75, 0,80, 0,85, 0,90, 0,95, 1,00
For each gridpoint defined in accordance with subpoints (d)(i) and (d)(ii) above the efficiency η shall be calculated in accordance with the following equations:
Where the actual value of the grid point for the normalised torque is smaller than zero:
ηTnorm,i, ωnorm,j
Tnorm,i ωnorm,j Ploss,normTnorm,i, ωnorm,j
Tnorm,i ωnorm,j
0,96
Where the resulting value for η is smaller than zero, it shall be set to zero.
Where the actual value of the grid point for the normalised torque is larger than zero:
ηTnorm,i, ωnorm,j
Tnorm,i ωnorm,j
Tnorm,i ωnorm,j Ploss,normTnorm,i, ωnorm,j
0,96
where:
ηefficiency [–]
Tnorm,inormalised torque for all gridpoints defined in accordance with subpoint (d)(ii) above [–]
ωnorm,jnormalised speed for all gridpoints defined in accordance with subpoint (d)(i) above [–]
Ploss,normnormalised loss power determined in accordance with subpoints (a) to (c) above [–]
From the efficiency map determined in accordance with subpoint (d) above, the actual power loss map of the electric machine system shall be calculated in accordance with the following provisions:
For each gridpoint of normalised speed defined in accordance with subpoint (d)(i) above the actual speed values nj shall be calculated in accordance with the following equation:
nj = ωnorm,j × nrated
where:
njactual speed [1/min]
ωnorm,jnormalised speed for all gridpoints defined in accordance with subpoint (d)(i) above [–]
nratedrated speed of the electric machine system determined from the data generated in accordance with Step 2 above [1/min]
For each gridpoint of normalised torque defined in accordance with subpoint (d)(ii) above the actual torque values Ti shall be calculated in accordance with the following equation:
Ti = Tnorm,i × Tmax
where:
Tiactual torque [Nm]
Tnorm,inormalised torque for all gridpoints defined in accordance with subpoint (d)(ii) above [–]
Tmaxoverall maximum torque of the electric machine system determined from the data generated in accordance with Step 2 above [Nm]
For each gridpoint defined in accordance with subpoints (e)(i) and (e)(ii) above the actual power loss shall be calculated in accordance with the following equation:
PlossTi, nj 1 n
Ti
Tmax
,
nj
nrated
Ti nj2π60
where:
Plossactual loss power [W]
Tiactual torque [Nm]
njactual speed [1/min]
ηefficiency dependent on normalised speed and torque determined in accordance with subpoint (d) above [–]
Tmaxoverall maximum torque of the electric machine system determined from the data generated in accordance with Step 2 above [Nm]
nratedrated speed of the electric machine system determined from the data generated in accordance with Step 2 above [1/min]
For each gridpoint defined in accordance with subpoints (e)(i) and (e)(ii) above the actual electric inverter power shall be calculated in accordance with the following equation:
PelTi, nj PlossTi, nj Ti nj2π60
where:
Pelactual electric inverter power [W]
Plossactual loss power [W]
Tiactual torque [Nm]
njactual speed [1/min]
The data of the actual electric power map determined in accordance with subpoint (e) above shall be extended in accordance with subpoints (1), (2), (4) and (5) of point 4.3.4 of this Annex.
Step 7: The drag curve shall be calculated based on the actual power loss map determined in accordance with subpoint (e) above in accordance with the following provisions:
From the power loss values for the two gridpoints defined by the normalised torque
Ti
Tmax
0,01, and values of 1,00 and 4,00 for normalised speed
nj
nrated
, the drag torque depending on actual speed and torque shall be calculated in accordance with the following equation:
Tdrag Ti
Ti
Tmax
0,01, n j
nj
nrated
1,00;4,00 Ploss Ti
Ti
Tmax
0,01, nj
nj
nrated
1,00;4,00602π nj
where:
Tdragactual drag torque [Nm]
Tiactual torque [Nm]
Tmaxoverall maximum torque of the electric machine system determined from the data generated in accordance with Step 2 above [Nm]
njactual speed [1/min]
nratedrated speed of the electric machine system determined from the data generated in accordance with Step 2 above [1/min]
Plossactual loss power [W]
From the two values of drag torque determined in accordance with subpoint (a) above, a third value of drag torque at zero rotational speed shall be calculated by means of linear extrapolation.
From the two values of drag torque determined in accordance with subpoint (a) above, a fourth value of drag torque at the maximum normalised speed value defined in accordance with subpoint (b)(i) of Step 6 above shall be calculated by means of linear extrapolation.
Step 8: The rotational inertia shall be determined by one of the following options:
Option 1: Based on the actual rotational inertia defined by the geometric form and the density of the respective materials of the rotor of the electric machine. Data and methods from a CAD software tool may be used to derive the actual rotational inertia of the rotor of the electric machine. The detailed method for determining the rotational inertia shall be agreed with the type approval authority.
Option 2: Based on the outer dimensions of the rotor of the electric machine. A hollow cylinder shall be defined to fit the dimensions of the rotor of the electric machine in a way that:
The outer diameter of the cylinder matches the point of the rotor with the largest distance from the rotational axis of the rotor assessed along a straight line orthogonal to the rotational axis of the rotor.
The inner diameter of the cylinder matches the point of the rotor with the smallest distance from the rotational axis of the rotor assessed along a straight line orthogonal to the rotational axis of the rotor.
The length of the cylinder matches the distance between the two points located furthest from each other assessed along a straight line parallel to the rotational axis of the rotor.
For the hollow cylinder defined in accordance with subpoints (i) to (iii) above the rotational inertia shall be calculated with a material density of 7850 kg/m3.