Battery system or representative battery subsystem
The following steps shall be performed to generate the input data for the battery system or representative battery subsystem based on standard values:
The battery type shall be determined based on the numerical ratio between maximum current in A (as indicated in accordance with point 1.4.4 of Annex 6 – Appendix 2 of UN Regulation No. 100 (***) and capacity in Ah (as indicated in accordance with point 1.4.3 of Annex 6 – Appendix 2 of UN Regulation No. 100). The battery type shall be “high-energy battery system (HEBS)” where this ratio is lower than 10 and shall be “high-power battery system (HPBS)” where this ratio is equal to or higher than 10.
The rated capacity shall be the value in Ah as indicated in accordance with paragraph 1.4.3 of Annex 6 – Appendix 2 of UN Regulation No. 100.
The OCV as a function of SOC shall be determined based on the nominal voltage in V, Vnom, as indicated in accordance with paragraph 1.4.1 of Annex 6 – Appendix 2 of UN Regulation No. 100. The values of OCV for different levels of SOC shall be calculated in accordance with the following table:
SOC [%] | OCV [V]
0 | 0,88 × Vnom
10 | 0,94 × Vnom
50 | 1,00 × Vnom
90 | 1,06 × Vnom
100 | 1,12 × Vnom
The DCIR shall be determined in accordance with the following provisions:
For HPBS in accordance with subpoint (a) above the DCIR shall be calculated by dividing the specific resistance of 25 [mOhm × Ah] by the rated capacity in Ah as defined in accordance with subpoint (b) above.
For HEBS in accordance with subpoint (a) above the DCIR shall be calculated by dividing the specific resistance of 140 [mOhm × Ah] by the rated capacity in Ah as defined in accordance with subpoint (b) above.
The values for maximum charging and maximum discharging current shall be determined in accordance with the following provisions:
For HPBS in accordance with subpoint (a) above the values for both, maximum charging and maximum discharging current, shall be set to the respective current in A corresponding to 10C.
For HEBS in accordance with subpoint (a) above the values for both, maximum charging and maximum discharging current, shall be set to the respective current in A corresponding to 1C.
Absolute values for both, maximum charging and maximum discharging current, shall be used as final values.
Capacitor system or representative capacitor subsystem
The following steps shall be performed to generate the input data for the capacitor system or representative capacitor subsystem based on standard values:
The capacitance shall be the rated capacitance as indicated in the datasheet of the capacitor system or representative capacitor subsystem. The actual capacitance of the capacitor system or representative capacitor subsystem may be determined by scaling up the rated capacitance of a single capacitor cell in accordance with the arrangement (i.e. series and/or parallel) of the single cells in the capacitor system or representative capacitor subsystem.
The maximum voltage, Vmax,Cap, shall be the rated voltage as indicated in the datasheet of the capacitor system or representative capacitor subsystem. The actual maximum voltage of the capacitor system or representative capacitor subsystem may be determined by scaling up the rated voltage of a single capacitor cell in accordance with the arrangement (i.e. series and/or parallel) of the single cells in the capacitor system or representative capacitor subsystem.
The minimum voltage, Vmin,Cap, shall be the value of Vmax,Cap determined in accordance with subpoint (b) above multiplied by 0,45.
The internal resistance shall be determined in accordance with the following equation:
RI,Cap RI,ref
Vmax,Cap Vmin,Cap
0,55 Vref
Cref
CCap
where:
RI,CapInternal resistance [Ohm]
RI,refReference for internal resistance with a numeric value of 0,015 [Ohm]
Vmax,CapMaximum voltage as defined in accordance with subpoint (b) above [V]
Vmin,CapMinimum voltage as defined in accordance with subpoint (c) above [V]
VrefReference for maximum voltage with a numeric value of 2,7 [V]
CrefReference for capacitance with a numeric value of 3000 [F]
CCapCapacitance as defined in accordance with subpoint (a) above [F]
The values for both, maximum charging and maximum discharging current, shall be calculated by multiplying the value of the capacitance in F as defined in accordance with subpoint (a) above by a factor of 5,0 [A/F]. Absolute values for both, maximum charging and maximum discharging current, shall be used as final values.