This Appendix describes the main evaluation steps and underlying basic equations that are applied by the simulation tool in a verification testing procedure simulation.
For the determination of the CVTP factor as described in point 7.2.2, the calculation procedures as set out below are applied:
Calculation of wheel power
The torque data as read from the processed measurement data in accordance with Table 4 is corrected for the torque meter drift as follows:
Tcorr it Tit Tdrift i
t tstart
tend tstart
where:
iindex standing for left and right wheel of the driven axle
Tcorrdrift corrected torque signal [Nm]
Ttorque signal before drift correction [Nm]
Tdrifttorque meter drift as recorded during drift check at the end of the verification test [Nm]
ttime node [s]
tstartfirst time stamp in the processed measurement data in accordance with Table 4 [s]
tendlast time stamp in the processed measurement data in accordance with Table 4 [s]
The wheel power is calculated from the corrected wheel torque and rotational wheel speed as follows:
Pwheel it2 π nwheel it Tcorr it60000
where:
iindex standing for left and right wheel of the driven axle
ttime node [s]
Pwheelwheel power [kW]
nwheelrotational wheel speed [rpm]
Tcorrdrift corrected torque signal [Nm]
The total wheel power is then calculated as the sum of the wheel power from left and right wheel:
Pwheelt
2i 1
Pwheel it
Determination of the measured brake specific fuel consumption (FCm-c)
The result for “brake specific fuel consumption measured and corrected for a run-in phase” (BSFCm-c) as applied for in 7.2.2 is calculated by the simulation tool as described below.
In a first step the raw value for measured brake specific fuel consumption for the verification test BSFCm is calculated as follows:
BSFCm
tendtstart
FCmt Δt
Wwheel,pos,m
where:
BSFCmraw value for measured brake specific fuel consumption in the verification test [g/kWh]
FCm (t)instantaneous fuel mass flow measured during the verification test [g/s]
Δttime increment duration = 0,5 [s]
Wwheel,pos,mpositive wheel work measured in the verification test [kWh]
Wwheel,pos,m
tendtstart
max Pwheelt,0 Δt3600
In a second step BSFCm is corrected for the net calorific value (NCV) of the fuel used in the verification test resulting in BSFCm,corr:
BSFCm,corr BSFCmNCVmeasNCVstd
where:
BSFCm,corrvalue for measured brake specific fuel consumption in the verification test corrected and for NCV influence [g/kWh]
NCVmeasNCV of the fuel used in the verification test determined in accordance with point 3.2 of Annex V [MJ/kg]
NCVstdstandard NCV in accordance with Table 5 in point 5.4.3.1 of Annex V [MJ/kg]
This correction is applied for all fuel types, i.e. also for Diesel CI engines (see footnote 2 in Table 4a).
In a third step the correction for a run-in phase is applied:
BSFCm c BSFCm,corr min1,ef mileage1 ef15 000 g/kWh
where:
BSFCm-cbrake specific fuel consumption measured and corrected for a run-in phase
efevolution coefficient of 0,98
mileagerun-in distance [km]
For dual-fuel vehicles all three evaluation steps are performed separately for both fuels.
Determination of the brake specific fuel consumption simulated by the simulation tool (BSFCsim)
In the verification test mode of the simulation tool the measured wheel power is applied as input to the backward simulation algorithm. The gears engaged during the verification test are determined by calculating the engine speeds per gear at the measured vehicle speed and selecting the gear that provides the engine speed closest to the measured engine speed. For APT transmissions during phases with active torque converter, the actual gear signal from the measurement is used.
The loss models for axle gear, angle drive, retarders, transmissions and PTOs are applied in a similar way as in the declaration mode of the simulation tool.
For power demand of auxiliary units concerning steering pump, pneumatic system, electric system and HVAC system the generic values as implemented per technology in the simulation tool are applied. For calculation of the power demand of the engine cooling fan the following formulas are applied:
Case a) non-electrically driven engine cooling fans:
Pfant C1 nfantC23 DfanC35
where:
Pfanpower demand engine cooling fan [kW]
ttime node [s]
nfanmeasured rotational speed of the fan [rpm]
Dfandiameter of the fan [mm]
C17,32 kW
C21200 rpm
C3810 mm
Case (b) electrically driven engine cooling fans:
Pfan(t) = Pel(t) . 1,05
Pfanpower demand engine cooling fan [kW]
ttime node [s]
Pelelectrical power at the terminals of the engine cooling fan(s) as measured in accordance with point 5.6.1.
In the case of vehicles with engine stop-start events during the verification test, similar corrections for auxiliary power demand and energy to re-start the engine as applied in the declaration mode of the simulation tool are applied.
The simulation of the engines instantaneous fuel consumption FCsim(t) is performed for each 0,5 second time interval as follows:
Interpolation from the engine fuel map using measured engine speed and resulting engine torque from the backward calculation including engines rotational inertia calculated from measured engine speed
The engine torque demand as determined above is limited to the certified engine full-load capabilities. For those time intervals the wheel power in the backward simulation is reduced accordingly. In the calculation of BSFCsim as set out below this simulated wheel power trace (Pwheel,sim(t)) is taken into consideration.
A WHTC correction factor is applied corresponding to the allocation of urban, rural and motorway based on the definitions as given in point 2(8) to 2(10) and the measured vehicle speed.
The brake specific fuel consumption calculated by the simulation tool BSFCm-c as applied in 7.2.2 for calculation of the CVTP factor is calculated as follows:
BSFCsim
tendtstart
FCsimt Δt FCESS,corr
Wwheel,pos,sim
where:
BSFCsimbrake specific fuel consumption determined by the simulation tool for the verification test [g/kWh]
ttime node [s]
FCsimengines instantaneous fuel consumption [g/s]
Δttime increment duration = 0,5 [s]
FCESS,corrcorrection of fuel consumption regarding auxiliary power demand resulting from engine stop start (ESS) as applied in the declaration mode of the simulation tool [g]
Wwheel,pos,simpositive wheel work determined by the simulation tool for the verification test [kWh]
Wwheel,pos,sim
tend
tstart
max Pwheel,simt,03600 fs
fsSimulation rate = 2 [Hz]
Pwheel,simSimulated wheel power for the verification test [kW]
In the case of dual-fuel engines, BSFCsim is determined for both fuels separately.
The engine power is calculated from the measured signals for engine speed and engine torque as follows:
Peng,mt2 π nengt Teng,mt60000
where:
Peng,mmeasured engine power in the verification test[kW]
ttime node [s]
nengmeasured rotational engine speed [rpm]
Tengmeasured engine torque [Nm]
The positive engine work measured in the verification test is calculated as follows:
Weng,pos,m
tend
tstart
max Peng,mt,03600 fs
Weng,pos,mpositive engine work measured in the verification test [kWh]
fssampling rate = 2 [Hz]
tstartfirst time stamp in the processed measurement data in accordance with Table 4 [s]
tendlast time stamp in the processed measurement data in accordance with Table 4 [s]
The brake specific pollutant emissions measured in the verification test BSEM are calculated as follows:
BSEM
tendtstart
EMt
Weng,pos,m fs
where:
BSEMbrake specific pollutant emissions measured in the verification test [g/kWh]
EMinstantaneous pollutant emission mass flow measured during the verification test [g/s]
(*) Council Directive 96/53/EC of 25 July 1996 laying down for certain road vehicles circulating within the Community the maximum authorized dimensions in national and international traffic and the maximum authorized weights in international traffic (OJ L 235, 17.9.96, p. 59).
(**) Only if this component needs to be measured in accordance with point 1 of Appendix 1 to Annex II to Regulation (EU) 582/2011.
(***) For positive ignition engines..