In order to allow using the provisions defined in this Appendix to generate input data for IEPC based fully or partially on standard values, the following conditions shall be fulfilled.
Where more than one electric machine system is part of the IEPC, all electric machines shall have the exact same specifications. Where more than one electric machine system is part of the IEPC, all electric machines shall be connected to the torque path of the IEPC at the same reference position (i.e. either upstream of gearbox or downstream of gearbox) where all electric machines shall be run at the same rotational speed at this reference position and their individual torque (power) shall be added by any kind of summation gearbox.
One of the following options shall be used to generate the input data for IEPC, based fully or partially on standard values:
Option 1: only standard values for all components part of the IEPC
The standard values for the electric machine system as part of the IEPC shall be determined in accordance with Appendix 8. Where multiple electric machines are part of the IEPC, the standard values in accordance with Appendix 8 shall be determined for a single electric machine and all figures for torque and power (mechanical and electrical) shall be multiplied by the total number of electric machines being part of the IEPC. The resulting values from this multiplication shall be used for all further steps in this Appendix.
The value for rotational inertia determined in accordance with Step 8 of Appendix 8 of this Annex shall be multiplied by the total number of electric machines being part of the IEPC.
Where a gearbox is included in the IEPC, the standard values for the IEPC shall be determined for each forward gear separately for the electric power consumption map, and only for the gear with the gear ratio closest to 1 for all other input data in accordance with the following procedure:
The standard values for losses in the gearbox shall be determined in accordance with point (2) of this Appendix.
For step number (i) above the rotational speed and torque points defined at the shaft of the electric machine system determined in accordance with subpoint (a) above shall be used as rotational speed and torque values at the input shaft of the gearbox.
In order to generate the required input data for IEPC in accordance with Appendix 15 referring to the output shaft of the gearbox, all torque values referring to the output shaft of the electric machine determined in accordance with subpoint (a) above shall be converted to the output shaft of the gearbox by the following equation:
Ti,GBX = (Ti,EM – Ti,l,in (nj,EM, Ti,EM, gear)) × igear
where:
Ti,GBXtorque at output shaft of gearbox
Ti,EMtorque at output shaft of electric machine system
Ti,l,intorque loss for each shiftable forward gear related to the input shaft of the gearbox parts of the IEPC determined in accordance with point (b)(i) above
nj,EMSpeed at the output shaft of electric machine system at which Ti,EM was measured [rpm]
igeargear ratio of a specific gear [-]
(where gear = 1, …, highest gear number)
In order to generate the required input data for IEPC in accordance with Appendix 15 referring to the output shaft of the gearbox, all speed values referring to the output shaft of the electric machine determined in accordance with subpoint (a) above shall be converted to the output shaft of the gearbox by the following equation:
nj,GBX = nj,EM / igear
where:
nj,EMSpeed at the output shaft of electric machine [rpm]
igeargear ratio of a specific gear [-]
(where gear = 1, …, highest gear number)
Where a differential is included in the IEPC, the standard values for the differential shall be determined for each forward gear separately for the electric power consumption map and only for the for the gear with the gear ratio closest to 1 for all other input data in accordance with the following steps:
The standard values for losses in the differential shall be determined in accordance with point (3) of this Appendix.
The torque points defined at the output shaft of the gearbox being part of the IEPC determined in accordance with subpoint (b) above shall be used as torque values at the input of the differential. Where no gearbox is included in the IEPC, the torque points defined at the output shaft of the electric machine system determined in accordance with subpoint (a) above shall be used as torque values at the input of the differential for step number (i) above.
In order to generate the required input data for IEPC in accordance with Appendix 15 referring to the output of the differential, all torque values referring to the output shaft of either the gearbox (where a gearbox is included in the IEPC) determined in accordance with step number (iii) of subpoint (b) above or the electric machine system (in the case that no gearbox is included in the IEPC) determined in accordance with subpoint (a) above shall be converted to the output of the differential by the following equation:
Ti,diff,out = (Ti,diff,in – Ti,diff,l,in (Ti,diff,in)) × idiff
where:
Ti,diff,outtorque at output of differential
Ti,diff,intorque at input of differential
Ti,diff,l,intorque loss related to the input of the differential dependent on the input torque determined in accordance with point (c)(i) above
idiffdifferential gear ratio [-]
In order to generate the required input data for IEPC in accordance with Appendix 15 referring to the output of the differential, all speed values referring to the output shaft of either the gearbox (where a gearbox is included in the IEPC) determined in accordance with step number (iv) of subpoint (b) above or the electric machine system (where no gearbox is included in the IEPC) determined in accordance with subpoint (a) above shall be converted to the output of the differential by the following equation:
nj,diff,out = nj,diff,in / idiff
where:
nj,diff,inspeed at input of differential [rpm]
idiffdifferential gear ratio [-]
Option 2: measurement of electric machine system as part of the IEPC and standard values for other components of IEPC
The measured component data for the electric machine system as part of the IEPC shall be determined in accordance with point 4 of this Annex. In the case of multiple electric machines being part of the IEPC, the component data shall be determined for a single electric machine and all figures for torque and power (mechanical and electrical) shall be multiplied by the total number of electric machines being part of the IEPC. The resulting values from this multiplication shall be used for all further steps in this Appendix.
The value for rotational inertia determined in accordance with point 8 of Appendix 8 of this Annex shall be multiplied by the total number of electric machines being part of the IEPC.
Where a gearbox is included in the IEPC, the standard values for the IEPC shall be determined for each forward gear separately for the electric power consumption map and only for the gear with the gear ratio closest to 1 for all other input data in accordance with the provisions of Option 1(b) above. In this context all references in Option 1(b) to subpoint (a) shall be understood as references to subpoint (a) of Option 2.
Where a differential is included in the IEPC, the standard values for the differential shall be determined for each forward gear separately for the electric power consumption map and only for the gear with the gear ratio closest to 1 for all other input data in accordance with Option 1(c) above. In this context all references in Option 1(c) to subpoint (b) shall be understood as references to subpoint (b) of Option 2.
IEPC internal component gearbox
The torque loss Tgbx,l,in for each shiftable forward gear related to the input shaft of the gearbox parts of the IEPC shall be calculated in accordance with the following provisions:
Tgbx,l,in (nin, Tin, gear) = Td0 + Td1000 × nin / 1000 rpm + fT,gear × Tin
where:
Tgbx,l,inTorque loss related to the input shaft [Nm]
TdxDrag torque at x rpm [Nm]
ninSpeed at the input shaft [rpm]
fT,gear
Gear dependent torque loss coefficient [-];
determined acc. to subpoints (b)-(f) below
TinTorque at the input shaft [Nm]
gear1, …, highest gear number [-]
The values of the equation shall be determined for all transmission gears located downstream of the EM output shaft.
Where a differential is included in the IEPC, the values of the equation shall be determined for all transmission gears located downstream of the EM output shaft and upstream of, but excluding the gear mesh with the differential input gear. The gear mesh with the differential input gear can be an external-external gear mesh (either spur or bevel) or a single planetary gearset.
In the case of wheel hub motors, the values of the equation shall be determined for all transmission gears located downstream of the EM output shaft and upstream of the wheel hub.
The value for fT shall be determined in accordance with paragraph 3.1.1 of Annex VI.
The value for fT shall be 0,007 for a direct gear.
The values for Td0 and Td1000 shall be 0,0075 × Tmax,in for gearboxes with more than 2 friction shift clutches.
The values for Td0 and Td1000 shall be 0,0025 × Tmax,in for all other gearboxes.
Tmax,in shall be the overall maximum value of all individual maximum allowed input torque for each forward gear of the gearbox in [Nm].
IEPC internal component differential
The torque loss Tdiff,l,in related to the input of the differential parts of the IEPC shall be calculated in accordance with the following provisions:
Tdiff,l,in (Tin) = ηdiff × Tdiff,d0 / idiff + (1- ηdiff) × Tin
where:
Tdiff,l,inTorque loss related to the input of the differential [Nm]
Tdiff,d0
Drag torque [Nm]
determined acc. to subpoints (e)-(f) below
ηdiff
Torque dependent efficiency [-];
determined acc. to subpoints (b)-(d) below
TinTorque at the input of the differential [Nm]
idiffdifferential gear ratio [-]
The values of the equation shall be determined for all gear meshes of the differential including the gear mesh with the differential input gear.
The value for ηdiff shall be determined in accordance with paragraph 3.1.1 of Annex VI, where in the respective equations ηm shall be set to 0,98 in the case of a bevel gear mesh.
The losses in the differential internal gears are shall be ignored for the calculations performed in accordance with subpoints (b)-(c) above.
In the case of a differential that includes a bevel gear mesh at the differential crown gear, the value for Tdiff,d0 shall be determined based on the following equation: Tdiff,d0 = 25 Nm + 15 Nm × idiff
In the case of a differential that includes a spur gear mesh or single planetary gearset at the differential input gear, the value for Tdiff,d0 shall be determined based on the following equation: Tdiff,d0 = 25 Nm + 5 Nm × idiff