Care should be taken to avoid cross-contamination between VTG samples of males and females.
After anaesthetisation, the caudal peduncle is partially severed with a scalpel blade and blood is collected from the caudal vein/artery with a heparinised microhematocrit capillary tube. After the blood has been collected, the plasma is quickly isolated by centrifugation for 3 min at 15000 g (or alternatively for 10 min. at 15000 g at 4 °C). If desired, percent haematocrit can be determined following centrifugation. The plasma portion is then removed from the microhematocrit tube and stored in a centrifuge tube with 0,13 units of aprotinin (a protease inhibitor) at – 80 °C until determination of VTG can be made. Depending on the size of the fathead minnow (which is sex-dependent), collectable plasma volumes generally range from 5 to 60 microliters per fish (Jensen et al. 2001).
Alternatively, blood may also be collected by cardiac puncture using a heparinised syringe (1000 units of heparin per ml). The blood is transferred into Eppendorf tubes (held on ice) and then centrifuged (5 min, 7000 g, room temperature). The plasma should be transferred into clean Eppendorf tubes (in aliquots if the volume of plasma makes this feasible) and promptly frozen at – 80 °C, until analysed (Panter et al., 1998).
Test fish should be removed from the test chamber using the small spoon-net. Be careful not to drop the test fish into other test chambers.
In principle, the test fish should be removed in the following order: control, solvent control (where appropriate), lowest concentration, middle concentration, highest concentration and positive control. In addition, all males should be removed from one test chamber before the remaining females are removed.
The sex of each test fish is identified on the basis of external secondary sex characteristics (e.g. the shape of the anal fin).
Place the test fish in a container for transport and carry it to the workstation for excision of the liver. Check the labels of the test chamber and the transport container for accuracy and to confirm that the number of fish that have been removed from the test chamber and that the number of fish remaining in the test chamber are consistent with expectation.
If the sex cannot be identified by the fish's external appearance, remove all fish from the test chamber. In this case, the sex should be identified by observing the gonad or secondary sex characteristics under a stereoscopic microscope.
Transfer the test fish from the container for transport to the anaesthetic solution using the small spoon-net.
After the test fish is anesthetised, transfer the test fish on the filter paper (or a paper towel) using tweezers (commodity type). When grasping the test fish, apply the tweezers to the sides of the head to prevent breaking the tail.
Wipe the water on the surface of the test fish on the filter paper (or the paper towel).
Place the fish abdomen side up. Then make a small transverse incision partway between the ventral neck region and the mid-abdominal region using dissection scissors.
Insert the dissection scissors into the small incision, and incise the abdomen from a point caudal to the branchial mantle to the cranial side of the anus along the midline of the abdomen. Be careful not to insert the dissection scissors too deeply so as to avoid damaging the liver and gonad.
Conduct the following operations under the stereoscopic microscope.
Place the test fish abdomen side up on the paper towel (glass Petri dish or slide glass are also available).
Extend the walls of the abdominal cavity with precision tweezers and exteriorise the internal organs. It is also acceptable to exteriorise the internal organs by removing one side of the wall of the abdominal cavity if necessary.
Expose the connected portion of the liver and gallbladder using another pair of precision tweezers. Then grasp the bile duct and cut off the gallbladder. Be careful not to break the gallbladder.
Grasp the oesophagus and excise the gastrointestinal tract from the liver in the same way. Be careful not to leak the contents of the gastrointestinal tract. Excise the caudal gastrointestinal tract from the anus and remove the tract from the abdominal cavity.
Trim the mass of fat and other tissues from the periphery of the liver. Be careful not to scratch the liver.
Grasp the hepatic portal area using the precision tweezers and remove the liver from the abdominal cavity.
Place the liver on the slide glass. Using the precision tweezers, remove any additional fat and extraneous tissue (e.g. abdominal lining), if needed, from the surface of the liver.
Measure the liver weight with 1,5 ml microtube as a tare using an electronic analytical balance. Record the value on the worksheet (read: 0,1 mg). Confirm the identification information on the microtube label.
Close the cap of the microtube containing the liver. Store it in a cooling rack (or ice rack).
Following the excision of one liver, clean the dissection instruments or replace them with clean ones.
Remove livers from all of the fish in the transport container as described above.
After the livers have been excised from all of the fish in the transport container (i.e., all males or females in a test chamber), place all liver specimens in a tube rack with a label for identification and store it in a freezer. When the livers are donated for pre-treatment shortly after the excision, the specimens are carried to the next workstation in a cooling rack (or ice rack).
Following liver excision, the fish carcass is available for gonad histology and measurement of secondary sex characteristics.
Store the liver specimens taken from the test fish at ≤ – 70 °C if they are not used for the pre-treatment shortly after the excision.
Take the bottle of homogenate buffer from the ELISA kit and cool it with crushed ice (temperature of the solution: ≤ 4°C). If homogenate buffer from EnBio ELISA system is used, thaw the solution at room temperature, and then cool the bottle with crushed ice.
Calculate the volume of homogenate buffer for the liver on the basis of its weight (add 50 μl of homogenate buffer per mg liver weight). For example, if the weight of the liver is 4,5 mg, the volume of homogenate buffer for the liver is 225 μl. Prepare a list of the volume of homogenate buffer for all livers.
Take the 1,5 ml microtube containing the liver from the freezer just before the pre-treatment.
Pre-treatment of the liver from males should be performed before females to prevent vitellogenin contamination. In addition, the pre-treatment for test groups should be conducted in the following order: control, solvent control (where appropriate), lowest concentration, middle concentration, highest concentration and positive control.
The number of 1,5 ml microtubes containing liver samples taken from the freezer at a given time should not exceed the number that can be centrifuged at that time.
Arrange the 1,5 ml microtubes containing liver samples in the order of specimen number on the ice rack (no need to thaw the liver).
Check the list for the volume of the homogenate buffer to be used for a particular sample of liver and adjust the micropipette (volume range: 100-1000 μl) to the appropriate volume. Attach a clean tip to the micropipette.
Take the homogenate buffer from the reagent bottle and add the buffer to the 1,5 ml microtube containing the liver.
Add the homogenate buffer to all of 1,5 ml microtubes containing the liver according to the procedure described above. There is no need to change the micropipette tip to a new one. However, if the tip is contaminated or suspected to be contaminated, the tip should be changed.
Attach a new pestle for homogenisation to the microtube homogeniser.
Insert the pestle into the 1,5 ml microtube. Hold the microtube homogeniser to press the liver between the surface of the pestle and the inner wall of the 1,5 ml microtube.
Operate the microtube homogeniser for 10 to 20 seconds. Cool the 1,5 ml microtube with crushed ice during the operation.
Lift up the pestle from the 1,5 ml microtube and leave it at rest for about 10 seconds. Then conduct a visual check of the state of the suspension.
If pieces of liver are observed in the suspension, repeat the operations (3) and (4) to prepare satisfactory liver homogenate.
Cool the suspended liver homogenate on the ice rack until centrifugation.
Change the pestle to the new one for each homogenate.
Homogenise all livers with homogenate buffer according to the procedure described above.
Confirm the temperature of the refrigerated centrifuge chamber at ≤ 5 °C.
Insert the 1,5 ml microtubes containing the suspended liver homogenate in refrigerated centrifuge (adjust the balance if necessary).
Centrifuge the suspended liver homogenate at 13000 g for 10 min at ≤ 5 °C. However, if the supernatants are adequately separated, centrifugal force and time may be adjusted as needed.
Following centrifugation, check that the supernatants are adequately separated (surface: lipid, intermediate: supernatant, bottom layer: liver tissue). If the separation is not adequate, centrifuge the suspension again under the same conditions.
Remove all specimens from the refrigerated centrifuge and arrange them in the order of specimen number on the ice rack. Be careful not to resuspend each separated layer after the centrifugation.
Place four 0,5 ml microtubes for storage of the supernatant into the tube rack.
Collect 30 μl of each supernatant (separated as the intermediate layer) with the micropipette and dispense it to one 0,5 ml microtube. Be careful not to collect the lipid on the surface or the liver tissue in the bottom layer.
Collect the supernatant and dispense it to other two 0,5 ml microtubes in the same manner as described above.
Collect the rest of the supernatant with the micropipette (if feasible: ≥ 100 μl). Then dispense the supernatant to the remaining 0,5 ml microtube. Be careful not to collect the lipid on the surface or the liver tissue in the bottom layer.
Close the cap of the 0,5 ml microtube and write the volume of the supernatant on the label. Then immediately cool the microtubes on the ice rack.
Change the tip of the micropipette to the new one for each supernatant. If a large amount of lipid becomes attached to the tip, change it to the new one immediately to avoid contamination of the liver extract with fat.
Dispense all of the centrifuged supernatant to four 0,5 ml microtubes according to the procedure described above.
After dispensing the supernatant to the 0,5 ml microtubes, place all of them in the tube rack with the identification label, and then freeze them in the freezer immediately. If the VTG concentrations are measured immediately after the pre-treatment, keep one 0,5 ml microtube (containing 30 μl of supernatant) cool in the tube rack and transfer it to the workstation where the ELISA assay is conducted. In such case, place the remaining microtubes in the tube racks and freeze them in the freezer.
After the collection of the supernatant, discard the residue adequately.
Store the 0,5 ml microtubes containing the supernatant of the liver homogenate at ≤ – 70 °C until they are used for the ELISA.
Immediately following anaesthesia, the caudal peduncle is severed transversely, and the blood is removed from the caudal artery/vein with a heparinised microhematocrit capillary tube. Blood volumes range from 5 to 15 microliters depending on fish size. An equal volume of aprotinin buffer (6 micrograms/ml in PBS) is added to the microcapillary tube, and plasma is separated from the blood via centrifugation (5 minutes at 600 g). Plasma is collected in the test tubes and stored at – 20 °C until analysed for VTG or other proteins of interest.
To avoid coagulation of blood and degradation of protein the samples are collected within Phosphate-buffered saline (PBS) buffer containing heparin (1000 units/ml) and the protease inhibitor aprotinin (2 TIU/ml). As ingredients for the buffer, heparin, ammonium-salt and lyophilised aprotinin are recommended. For blood sampling, a syringe (1ml) with a fixed thin needle (e.g. Braun Omnikan-F) is recommended. The syringe should be prefilled with buffer (approximately 100 microliter) to completely elute the small blood volumes from each fish. The blood samples are taken by cardiac puncture. At first the fish should be anesthetized with MS-222 (100 mg/l). The proper plane of anaesthesia allows the user to distinguish the heartbeat of the zebrafish. While puncturing the heart, keep the syringe piston under weak tension. Collectable blood volumes range between 20 - 40 microliters. After cardiac puncture, the blood/buffer-mixture should be filled into the test tube. Plasma is separated from the blood via centrifugation (20 min; 5000 g) and should be stored at – 80°C until required for analysis.
The fish are anaesthetised and euthanised in accordance with the test description.
The head and tail are cut of the fish in accordance with Figure 1.
Important: All dissection instruments, and the cutting board should be rinsed and cleaned properly (e.g. with 96 % ethanol) between handling of each single fish to prevent “vitellogenin pollution” from females or induced males to uninduced males.
The weight of the pooled head and tail from each fish is measured to the nearest mg.
After being weighed, the parts are placed in appropriate tubes (e.g. 1,5 ml eppendorf) and frozen at – 80 °C until homogenisation or directly homogenised on ice with two plastic pistils. (Other methods can be used if they are performed on ice and the result is a homogenous mass). Important: The tubes should be numbered properly so that the head and tail from the fish can be related to their respective body-section used for gonad histology.
When a homogenous mass is achieved, 4 x the tissue weight of ice-cold homogenisation buffer [Homogenisation buffer: (50 mM Tris-HCl pH 7,4; 1 % Protease inhibitor cocktail (Sigma)): 12 ml Tris-HCl pH 7,4 + 120 μl Protease inhibitor cocktail. TRIS: TRIS-ULTRA PURE (ICN) e.g. from Bie & Berntsen, Denmark. Protease inhibitor cocktail: From Sigma (for mammalian tissue) Product number P 8340. NOTE: The homogenisation buffer should be used the same day as manufactured. Place on ice during use.] is added. Keep working with the pistils until the mixture is homogeneous. Important note: New pistils are used for each fish.
The samples are placed on ice until centrifugation at 4 °C at 50000 g for 30 min.
Use a pipette to dispense portions of 20 μl supernatant into at least two tubes by dipping the tip of the pipette below the fat layer on the surface and carefully sucking up the supernatant without fat- or pellet fractions.
The tubes are stored at – 80 °C until use.