49 SUBPART N FLIGHT CREW, Commission Regulation (EC) No 859/2008 of 20 August 2008 amending Council Regulation (EE…

In forcesince 20 Aug 2008
(a)

An operator shall ensure that:

1.

the composition of the flight crew and the number of flight crew members at designated crew stations are both in compliance with, and no less than the minimum specified in, the Aeroplane Flight Manual (AFM);

2.

the flight crew includes additional flight crew members when required by the type of operation, and is not reduced below the number specified in the Operations Manual;

3.

all flight crew members hold an applicable and valid licence acceptable to the Authority and are suitably qualified and competent to conduct the duties assigned to them;

4.

procedures are established, acceptable to the Authority, to prevent the crewing together of inexperienced flight crew members;

5.

one pilot amongst the flight crew, qualified as a pilot-in-command in accordance with the requirements governing Flight Crew Licenses, is designated as the commander who may delegate the conduct of the flight to another suitably qualified pilot; and

6.

when a dedicated System Panel Operator is required by the AFM, the flight crew includes one crew member who holds a Flight Engineer's licence or is a suitably qualified flight crew member and acceptable to the Authority.

7.

when engaging the services of flight crew members who are self employed and/or working on a freelance or part time basis, the requirements of Subpart N are complied with. In this respect, particular attention must be paid to the total number of aircraft types or variants that a flight crew member may fly for the purposes of commercial air transportation, which must not exceed the requirements prescribed in OPS 1.980 and OPS 1.981, including when his/her services are engaged by another operator. For crew members serving the operator as a commander, initial operator's crew resource management (CRM) training shall be completed before commencing unsupervised line flying unless the crew member has previously completed an initial operator's CRM course.

(b)

Minimum flight crew for operations under IFR or at night. For operations under IFR or at night, an operator shall ensure that:

1.

for all turbo-propeller aeroplanes with a maximum approved passenger seating configuration of more than nine and for all turbo-jet aeroplanes, the minimum flight crew is two pilots; or

2.

aeroplanes other than those covered by subparagraph (b)1 above are operated by a single pilot provided that the requirements of Appendix 2 to OPS 1.940 are satisfied. If the requirements of Appendix 2 are not satisfied, the minimum flight crew is two pilots.

(a)

When a flight crew member has not previously completed initial operator's crew resource management (CRM) training (either new employees or existing staff), then the operator shall ensure that the flight crew member completes an initial CRM training course. New employees shall complete initial operator's CRM Training within their first year of joining an operator.

(b)

If the flight crew member has not previously been trained in human factors then a theoretical course, based on the human performance and limitations programme for the ATPL (see the requirements applicable to the issue of Flight Crew Licences) shall be completed before the initial operator's CRM training or combined with the initial operator's CRM training.

(c)

Initial CRM training shall be conducted by at least one CRM trainer acceptable to the Authority who may be assisted by experts in order to address specific areas.

(d)

Initial CRM training is conducted in accordance with a detailed course syllabus included in the Operations Manual.

(a)

An operator shall ensure that:

1.

a flight crew member completes a Type Rating course which satisfies the requirements applicable to the issue of Flight Crew Licences when changing from one type of aeroplane to another type or class for which a new type or class rating is required;

2.

a flight crew member completes an operator's conversion course before commencing unsupervised line flying;

(i)

when changing to an aeroplane for which a new type or class rating is required; or

(ii)

when changing operator;

3.

conversion training is conducted by suitably qualified personnel in accordance with a detailed course syllabus included in the Operations Manual. The operator shall ensure that the personnel integrating elements of CRM into conversion training are suitably qualified;

4.

the amount of training required by the operator's conversion course is determined after due note has been taken of the flight crew member's previous training as recorded in his/her training records prescribed in OPS 1.985;

5.

the minimum standards of qualification and experience required of flight crew members before undertaking conversion training are specified in the Operations Manual;

6.

each flight crew member undergoes the checks required by OPS 1.965(b) and the training and checks required by OPS 1.965(d) before commencing line flying under supervision;

7.

upon completion of line flying under supervision, the check required by OPS 1.965(c) is undertaken;

8.

once an operator's conversion course has been commenced, a flight crew member does not undertake flying duties on another type or class until the course is completed or terminated; and

9.

elements of CRM training are integrated into the conversion course.

(b)

In the case of changing aeroplane type or class, the check required by OPS 1.965(b) may be combined with the type or class rating skill test under the requirements applicable to the issue of Flight Crew Licences.

(c)

The operator's conversion course and the type or class rating course required for the issue of Flight Crew Licences may be combined.

(d)

A pilot, undertaking a zero flight time training (ZFTT) course, shall:

1.

commence line flying under supervision as soon as possible within 21 days after completion of the skill test.

If line flying under supervision has not been commenced within the 21 days, the operator shall provide appropriate training acceptable to the Authority.

2.

complete six take-offs and landings in a flight simulator, qualified in accordance with the requirements applicable to synthetic training devices and user approved by the Authority, not later than 21 days after the completion of the skill test.

This simulator session shall be conducted by a type rating instructor for aeroplanes (TRI(A)) occupying a pilot's seat.

When recommended by a JOINT OPERATIONAL EVALUATION Board (JOEB) and approved by the Authority, the number of take-offs and landings may be reduced.

If these take-offs and landings have not been performed within the 21 days, the operator shall provide refresher training acceptable to the Authority;

3.

conduct the first four take-offs and landings of the Line Flying Under Supervision in the aeroplane under the supervision of a TRI(A) occupying a pilot's seat.

When recommended by a joint operational evaluation board (JOEB) and approved by the Authority, the number of take-offs and landings may be reduced.

(a)

An operator shall ensure that a flight crew member completes:

1.

differences training which requires additional knowledge and training on an appropriate training device for the aeroplane:

(i)

when operating another variant of an aeroplane of the same type or another type of the same class currently operated; or

(ii)

when changing equipment and/or procedures on types or variants currently operated;

2.

familiarisation training which requires the acquisition of additional knowledge:

(i)

when operating another aeroplane of the same type or variant; or

(ii)

when changing equipment and/or procedures on types or variants currently operated.

(b)

The operator shall specify in the Operations Manual when such differences training or familiarisation training is required.

(a)

An operator shall ensure that for upgrade to commander from co-pilot and for those joining as commanders:

1.

A minimum level of experience, acceptable to the Authority, is specified in the Operations Manual; and

2.

For multi-crew operations, the pilot completes an appropriate command course.

(b)

The command course required by subparagraph (a)2 above must be specified in the Operations Manual and include at least the following:

1.

training in an STD (including line orientated flying training) and/or flying training;

2.

an operator proficiency check operating as commander;

3.

commander's responsibilities;

4.

line training in command under supervision. A minimum of 10 sectors is required for pilots already qualified on the aeroplane type;

5.

completion of a commander's line check as prescribed in OPS 1.965(c) and route and aerodrome competence qualifications as prescribed in OPS 1.975; and

6.

elements of Crew Resource Management.

(a)

An operator shall ensure that:

1.

A Commercial Pilot Licence (CPL) holder does not operate as a commander of an aeroplane certificated in the Aeroplane Flight Manual for single pilot operations unless:

(i)

when conducting passenger carrying operations under Visual Flight Rules (VFR) outside a radius of 50 nm from an aerodrome of departure, the pilot has a minimum of 500 hours total flight time on aeroplanes or holds a valid Instrument Rating; or

(ii)

when operating on a multi-engine type under Instrument Flight Rules (IFR), the pilot has a minimum of 700 hours total flight time on aeroplanes which includes 400 hours as pilot-in-command (in accordance with the requirements governing Flight Crew Licenses) of which 100 hours have been under IFR including 40 hours multi-engine operation. The 400 hours as pilot-in-command may be substituted by hours operating as co-pilot on the basis of two hours co-pilot is equivalent to one hour as pilot-in-command provided those hours were gained within an established multi-pilot crew system prescribed in the Operations Manual;

2.

in addition to subparagraph (a)1(ii) above, when operating under IFR as a single pilot, the requirements prescribed in Appendix 2 to OPS 1.940 are satisfied; and

3.

in multi-pilot crew operations, in addition to subparagraph (a)1 above, and prior to the pilot operating as commander, the command course prescribed in OPS 1.955(a)2 is completed.

(a)

General. An operator shall ensure that:

1.

each flight crew member undergoes recurrent training and checking and that all such training and checking is relevant to the type or variant of aeroplane on which the flight crew member operates;

2.

a recurrent training and checking programme is established in the Operations Manual and approved by the Authority;

3.

recurrent training is conducted by the following personnel:

(i)

ground and refresher training — by suitably qualified personnel;

(ii)

aeroplane/STD training — by a type rating instructor (TRI), class rating instructor (CRI) or in the case of the STD content, a synthetic flight instructor (SFI), providing that the TRI, CRI or SFI satisfies the operator's experience and knowledge requirements sufficient to instruct on the items specified in paragraphs (a)1.(i)(A) and (B) of Appendix 1 to OPS 1.965;

(iii)

emergency and safety equipment training — by suitably qualified personnel; and

(iv)

crew resource management (CRM):

(A) integration of CRM elements into all the phases of the recurrent training — by all the personnel conducting recurrent training. The operator shall ensure that all personnel conducting recurrent training are suitably qualified to integrate elements of CRM into this training;

(B) modular CRM training — by at least one CRM trainer acceptable to the Authority who may be assisted by experts in order to address specific areas;

4.

recurrent checking is conducted by the following personnel:

(i)

operator proficiency checks — by a type rating examiner (TRE), class rating examiner (CRE) or, if the check is conducted in a STD, a TRE, CRE or a synthetic flight examiner (SFE), trained in CRM concepts and the assessment of CRM skills;

(ii)

line checks — by suitably qualified commanders nominated by the operator and acceptable to the Authority;

(iii)

emergency and safety equipment checking — by suitably qualified personnel.

(b)

Operator proficiency check

1.

An operator shall ensure that:

(i)

each flight crew member undergoes operator proficiency checks to demonstrate his/her competence in carrying out normal, abnormal and emergency procedures; and

(ii)

the check is conducted without external visual reference when the flight crew member will be required to operate under IFR;

(iii)

each flight crew member undergoes operator proficiency checks as part of a normal flight crew complement.

2.

The period of validity of an operator proficiency check shall be six calendar months in addition to the remainder of the month of issue. If issued within the final three calendar months of validity of a previous operator proficiency check, the period of validity shall extend from the date of issue until six calendar months from the expiry date of that previous operator proficiency check.

(c)

Line Check. An operator shall ensure that each flight crew member undergoes a line check on the aeroplane to demonstrate his/her competence in carrying out normal line operations described in the Operations Manual. The period of validity of a line check shall be 12 calendar months, in addition to the remainder of the month of issue. If issued within the final three calendar months of validity of a previous line check the period of validity shall extend from the date of issue until 12 calendar months from the expiry date of that previous line check.

(d)

Emergency and Safety Equipment training and checking. An operator shall ensure that each flight crew member undergoes training and checking on the location and use of all emergency and safety equipment carried. The period of validity of an emergency and safety equipment check shall be 12 calendar months in addition to the remainder of the month of issue. If issued within the final three calendar months of validity of a previous emergency and safety check, the period of validity shall extend from the date of issue until 12 calendar months from the expiry date of that previous emergency and safety equipment check.

(e)

CRM. An operator shall ensure that:

1.

elements of CRM are integrated into all appropriate phases of the recurrent training, and;

2.

each flight crew member undergoes specific modular CRM training. All major topics of CRM training shall be covered over a period not exceeding three years;

(f)

Ground and refresher training. An operator shall ensure that each flight crew member undergoes ground and refresher training at least every 12 calendar months. If the training is conducted within 3 calendar months prior to the expiry of the 12 calendar months period, the next ground and refresher training must be completed within 12 calendar months of the original expiry date of the previous ground and refresher training.

(g)

Aeroplane/STD training. An operator shall ensure that each flight crew member undergoes aeroplane/STD training at least every 12 calendar months. If the training is conducted within 3 calendar months prior to the expiry of the 12 calendar months period, the next aeroplane STD training must be completed within 12 calendar months of the original expiry date of the previous aeroplane/STD training.

(a)

An operator shall ensure that:

1.

a pilot who may be assigned to operate in either pilot's seat completes appropriate training and checking; and

2.

the training and checking programme is specified in the Operations Manual and is acceptable to the Authority.

(a)

An operator shall ensure that:

1.

a pilot is not assigned to operate an aeroplane as part of the minimum certificated crew, either as pilot flying or pilot non-flying unless he/she has carried out three take-offs and three landings in the previous 90 days as pilot flying in an aeroplane, or in a flight simulator of the same type/class.

2.

a pilot who does not hold a valid instrument rating is not assigned to operate an aeroplane at night as commander unless he/she has carried out at least one landing at night in the preceding 90 days as pilot flying in an aeroplane, or in a flight simulator, of the same type/class.

(b)

The 90-day period prescribed in subparagraphs (a)1 and 2 above may be extended up to a maximum of 120 days by line flying under the supervision of a type rating instructor or examiner. For periods beyond 120 days, the recency requirement is satisfied by a training flight or use of a flight simulator of the aeroplane type to be used.

(a)

An operator shall ensure that, prior to being assigned as commander or as pilot to whom the conduct of the flight may be delegated by the commander, the pilot has obtained adequate knowledge of the route to be flown and of the aerodromes (including alternates), facilities and procedures to be used.

(b)

The period of validity of the route and aerodrome competence qualification shall be 12 calendar months in addition to the remainder of:

1.

the month of qualification; or

2.

the month of the latest operation on the route or to the aerodrome.

(c)

Route and aerodrome competence qualification shall be revalidated by operating on the route or to the aerodrome within the period of validity prescribed in subparagraph (b) above.

(d)

If revalidated within the final three calendar months of the validity of the previous route and aerodrome competence qualification, the period of validity shall extend from the date of revalidation until 12 calendar months from the expiry date of that previous route and aerodrome competence qualification.

(a)

An operator, following a minimum of two years continuous operations, may substitute the training and checking requirements for flight crew specified in Appendix 1 to OPS 1.978(a) by an alternative training and Qualification programme (ATQP) approved by the Authority. The two years continuous operations may be reduced at the discretion of the Authority.

(b)

The ATQP must contain training and checking which establishes and maintains a level of proficiency demonstrated to be at least not less than the level of proficiency achieved by following the provisions of OPS 1.945, 1.965 and 1.970. The standard of flight crew training and qualification shall be established prior to the introduction of ATQP; the required ATQP training and qualification standards shall also be specified.

(c)

An operator applying for approval to implement an ATQP shall provide the Authority with an implementation plan in accordance with paragraph (c) of Appendix 1 to OPS 1.978.

(d)

In addition to the checks required by OPS 1.965 and 1.970 an operator shall ensure that each flight crew member undergoes a Line Orientated Evaluation (LOE).

1.

The line orientated evaluation (LOE) shall be conducted in a simulator. The LOE may be undertaken with other approved ATQP training.

2.

The period of validity of a LOE shall be 12 calendar months, in addition to the remainder of the month of issue. If issued within the final three calendar months of validity of a previous LOE the period of validity shall extend from the date of issue until 12 calendar months from the expiry date of that previous LOE.

(e)

After two years of operating within an approved ATQP an operator may, with the approval of the Authority, extend the periods of validity of OPS 1.965 and 1.970 as follows:

1.

operator proficiency check — 12 calendar months in addition to the remainder of the month of issue. If issued within the final three calendar months of validity of a previous operator proficiency check, the period of validity shall extend from the date of issue until 12 calendar months from the expiry date of that previous operator proficiency check;

2.

line check — 24 calendar months in addition to the remainder of the month of issue. If issued within the final six calendar months of validity of a previous line check, the period of validity shall extend from the date of issue until 24 calendar months from the expiry date of that previous line check. The line check may be combined with a line oriented quality evaluation (LOQE) with the approval of the authority;

3.

emergency and safety equipment checking — 24 calendar months in addition to the remainder of the month of issue. If issued within the final 6 calendar months of validity of a previous check, the period of validity shall extend from the date of issue until 24 calendar months from the expiry date of that previous check.

(f)

The ATQP shall be the responsibility of a nominated post holder.

(a)

An operator shall ensure that a flight crew member does not operate on more than one type or variant unless the flight crew member is competent to do so.

(b)

When considering operations of more than one type or variant, an operator shall ensure that the differences and/or similarities of the aeroplanes concerned justify such operations, taking account of the following:

1.

the level of technology;

2.

operational procedures;

3.

handling characteristics.

(c)

An operator shall ensure that a flight crew member operating more than one type or variant complies with all of the requirements prescribed in Subpart N for each type or variant unless the Authority has approved the use of credit(s) related to the training, checking and recent experience requirements.

(d)

An operator shall specify appropriate procedures and/or operational restrictions, approved by the Authority, in the Operations Manual, for any operation on more than one type or variant covering:

1.

the flight crew members' minimum experience level;

2.

the minimum experience level on one type or variant before beginning training for and operation of another type or variant;

3.

the process whereby flight crew qualified on one type or variant will be trained and qualified on another type or variant;

4.

all applicable recent experience requirements for each type or variant.

(a)

When a flight crew member operates both helicopters and aeroplanes:

1.

an operator shall ensure that operations of helicopter and aeroplane are limited to one type of each;

2.

the operator shall specify appropriate procedures and/or operational restrictions, approved by the Authority, in the Operations Manual.

(a)

An operator shall:

1.

maintain records of all training, checking and qualification prescribed in OPS 1.945, 1.955, 1.965, 1.968 and 1.975 undertaken by a flight crew member; and

2.

make the records of all conversion courses and recurrent training and checking available, on request, to the flight crew member concerned.