24 SUBPART F PERFORMANCE GENERAL, Commission Regulation (EC) No 859/2008 of 20 August 2008 amending Council Regulation (EE…

In forcesince 20 Aug 2008
(a)

An operator shall ensure that multi-engine aeroplanes powered by turbo propeller engines with a maximum approved passenger seating configuration of more than 9 or a maximum take-off mass exceeding 5700 kg, and all multi-engine turbojet powered aeroplanes are operated in accordance with Subpart G (Performance Class A).

(b)

An operator shall ensure that propeller driven aeroplanes with a maximum approved passenger seating configuration of nine or less, and a maximum take-off mass of 5700 kg or less are operated in accordance with Subpart H (Performance Class B).

(c)

An operator shall ensure that aeroplanes powered by reciprocating engines with a maximum approved passenger seating configuration of more than nine or a maximum take-off mass exceeding 5700 kg are operated in accordance with Subpart I (Performance Class C).

(d)

Where full compliance with the requirements of the appropriate Subpart cannot be shown due to specific design characteristics (e.g. supersonic aeroplanes or seaplanes), the operator shall apply approved performance standards that ensure a level of safety equivalent to that of the appropriate Subpart.

(a)

An operator shall ensure that the mass of the aeroplane:

1.

at the start of the take-off; or, in the event of in-flight re-planning;

2.

at the point from which the revised operational flight plan applies, is not greater than the mass at which the requirements of the appropriate Subpart can be complied with for the flight to be undertaken, allowing for expected reductions in mass as the flight proceeds, and for such fuel jettisoning as is provided for in the particular requirement.

(b)

An operator shall ensure that the approved performance Data contained in the Aeroplane Flight Manual is used to determine compliance with the requirements of the appropriate Subpart, supplemented as necessary with other data acceptable to the Authority as prescribed in the relevant Subpart. When applying the factors prescribed in the appropriate Subpart, account may be taken of any operational factors already incorporated in the Aeroplane Flight Manual performance data to avoid double application of factors.

(c)

When showing compliance with the requirements of the appropriate Subpart, due account shall be taken of aeroplane configuration, environmental conditions and the operation of systems which have an adverse effect on performance.

(d)

For performance purposes, a damp runway, other than a grass runway, may be considered to be dry.

(e)

An operator shall take account of charting accuracy when assessing compliance with the take-off requirements of the applicable subpart.

(a)

The following terms used in Subparts F, G, H, I and J, have the following meaning:

1.

“Accelerate-stop distance available (ASDA)”. The length of the take-off run available plus the length of stop way, if such stop way is declared available by the appropriate Authority and is capable of bearing the mass of the aeroplane under the prevailing operating conditions;

2.

“Contaminated runway”. A runway is considered to be contaminated when more than 25 % of the runway surface area (whether in isolated areas or not) within the required length and width being used is covered by the following:

(i)

surface water more than 3 mm (0,125 in) deep, or by slush, or loose snow, equivalent to more than 3 mm (0,125 in) of water;

(ii)

snow which has been compressed into a solid mass which resists further compression and will hold together or break into lumps if picked up (compacted snow); or

(iii)

ice, including wet ice.

3.

“Damp runway”. A runway is considered damp when the surface is not dry, but when the moisture on it does not give it a shiny appearance.

4.

“Dry runway”. A dry runway is one which is neither wet nor contaminated, and includes those paved runways which have been specially prepared with grooves or porous pavement and maintained to retain “effectively dry” braking action even when moisture is present.

5.

“Landing distance available (LDA)”. The length of the runway which is declared available by the appropriate Authority and suitable for the ground run of an aeroplane landing.

6.

“Maximum approved passenger seating configuration”. The maximum passenger seating capacity of an individual aeroplane, excluding pilot seats or flight deck seats and cabin crew seats as applicable, used by the operator, approved by the Authority and specified in the Operations Manual.

7.

“Take-off distance available (TODA)”. The length of the take-off run available plus the length of the clearway available.

8.

“Take-off mass”. The take-off mass of the aeroplane shall be taken to be its mass, including everything and everyone carried at the commencement of the take-off run.

9.

“Take-off run available (TORA)”. The length of runway which is declared available by the appropriate Authority and suitable for the ground run of an aeroplane taking off.

10.

“Wet runway”. A runway is considered wet when the runway surface is covered with water, or equivalent, less than specified in subparagraph (a)2. above or when there is sufficient moisture on the runway surface to cause it to appear reflective, but without significant areas of standing water.

(b)

The terms “accelerate-stop distance”, “take-off distance”, “take-off run”, “net take-off flight path”, “one engine inoperative en-route net flight path” and “two engines inoperative en-route net flight path” as relating to the aeroplane have their meanings defined in the airworthiness requirements under which the aeroplane was certificated, or as specified by the Authority if it finds that definition inadequate for showing compliance with the performance operating limitations.