18 Appendix 1 (New) to OPS 1.430 Aerodrome operating minima, Commission Regulation (EC) No 859/2008 of 20 August 2008 amending Council Regulation (EE…

In forcesince 20 Aug 2008
(a)

Take-off minima

1.

General

(i)

Take-off minima established by the operator must be expressed as visibility or RVR limits, taking into account all relevant factors for each aerodrome planned to be used and the aeroplane characteristics. Where there is a specific need to see and avoid obstacles on departure and/or for a forced landing, additional conditions (e.g. ceiling) must be specified.

(ii)

The commander shall not commence take-off unless the weather conditions at the aerodrome of departure are equal to or better than applicable minima for landing at that aerodrome unless a suitable take-off alternate aerodrome is available.

(iii)

When the reported meteorological visibility is below that required for take-off and RVR is not reported, a take-off may only be commenced if the commander can determine that the RVR/visibility along the take-off runway is equal to or better than the required minimum.

(iv)

When no reported meteorological visibility or RVR is available, a take-off may only be commenced if the commander can determine that the RVR/visibility along the take-off runway is equal to or better than the required minimum.

2.

Visual reference. The take-off minima must be selected to ensure sufficient guidance to control the aeroplane in the event of both a discontinued take-off in adverse circumstances and a continued take-off after failure of the critical power unit.

3.

Required RVR/visibility

(i)

For multi-engined aeroplanes, whose performance is such that, in the event of a critical power unit failure at any point during take-off, the aeroplane can either stop or continue the take-off to a height of 1500 ft above the aerodrome while clearing obstacles by the required margins, the take-off minima established by an operator must be expressed as RVR/Visibility values not lower than those given in Table 1 below except as provided in paragraph 4. below:

Note 1: The higher values apply to Category D aeroplanes.

Note 2: For night operations at least runway edge and runway end lights are required.

Note 3: The reported RVR/visibility value representative of the initial part of the take-off run can be replaced by pilot assessment.

Note 4: The required RVR value must be achieved for all of the relevant RVR reporting points with the exception given in Note 3 above.

Take-off RVR/visibility

Facilities |

RVR/visibility

(Note 3)

Nil (day only) | 500 m

Runway edge lighting and/or centreline marking |

250/300 m

(Notes 1 and 2)

Runway edge and centreline lighting |

200/250 m

(Note 1)

Runway edge and centreline lighting and multiple RVR information |

150/200 m

(Notes 1 and 4)

(ii)

For multi-engined aeroplanes whose performance is such that they cannot comply with the performance conditions in subparagraph (a)(3)(i) above in the event of a critical power unit failure, there may be a need to re-land immediately and to see and avoid obstacles in the take-off area. Such aeroplanes may be operated to the following take-off minima provided they are able to comply with the applicable obstacle clearance criteria, assuming engine failure at the height specified. The take-off minima established by an operator must be based upon the height from which the one engine inoperative net take-off flight path can be constructed. The RVR minima used may not be lower than either of the values given in Table 1 above or Table 2 below.

Note 1:1500 m is also applicable if no positive take-off flight path can be constructed.

Note 2: The reported RVR/visibility value representative of the initial part of the take-off run can be replaced by pilot assessment.

Take — off RVR/visibility

Assumed engine failure height above the take-off runway |

RVR/visibility

(Note 2)

< 50 ft | 200 m

51-100 ft | 300 m

101-150 ft | 400 m

151-200 ft | 500 m

201-300 ft | 1000 m

> 300 ft |

1500 m

(Note 1)

(iii)

When reported RVR, or meteorological visibility is not available, the commander shall not commence take-off unless he can determine that the actual conditions satisfy the applicable take-off minima.

4.

Exceptions to subparagraph (a)(3)(i) above:

(i)

Subject to the approval of the Authority, and provided the requirements in paragraphs (A) to (E) below have been satisfied, an operator may reduce the take-off minima to 125 m RVR (Category A, B and C aeroplanes) or 150 m RVR (Category D aeroplanes) when:

(A) low visibility procedures are in force;

(B) high intensity runway centreline lights spaced 15 m or less and high intensity edge lights spaced 60 m or less are in operation;

(C) flight crew members have satisfactorily completed training in a Flight Simulator;

(D) a 90 m visual segment is available from the cockpit at the start of the take-off run; and

(E) the required RVR value has been achieved for all of the relevant RVR reporting points

(ii)

Subject to the approval of the Authority, an operator of an aeroplane using either:

(A) an approved lateral guidance system; or,

(B) an approved HUD/HUDLS for take-off may reduce the take-off minima to an RVR less than 125 m (Category A, B and C aeroplanes) or 150 m (Category D aeroplanes) but not lower than 75 m provided runway protection and facilities equivalent to Category III landing operations are available.

(b)

Category I, APV and non-precision approach operations

1.

A Category I approach operation is a precision instrument approach and landing using ILS, MLS, GLS (GNSS/GBAS) or PAR with a decision height not lower than 200 ft and with an RVR not less than 550 m, unless accepted by the Authority.

2.

A non-precision approach (NPA) operation is an instrument approach using any of the facilities described in Table 3 (System minima), with a MDH or DH not lower than 250 ft and an RVR/CMV of not less than 750 m, unless accepted by the Authority.

3.

An APV operation is an instrument approach which utilises lateral and vertical guidance, but does not meet the requirements established for precision approach and landing operations, with a DH not lower than 250 ft and a runway visual range of not less than 600m unless approved by the Authority.

4.

Decision height (DH). An operator must ensure that the decision height to be used for an approach is not lower than:

(i)

the minimum height to which the approach aid can be used without the required visual reference; or

(ii)

the OCH for the category of aeroplane; or

(iii)

the published approach procedure decision height where applicable; or

(iv)

200 ft for Category I approach operations; or

(v)

the system minimum in Table 3; or

(vi)

the lowest decision height specified in the Aeroplane Flight Manual (AFM) or equivalent document, if stated;

whichever is higher.

5.

Minimum descent height (MDH). An operator must ensure that the minimum descent height for an approach is not lower than:

(i)

the OCH for the category of aeroplane; or

(ii)

the system minimum in Table 3; or

(iii)

the minimum descent height specified in the Aeroplane Flight Manual (AFM) if stated;

whichever is higher.

6.

Visual reference. A pilot may not continue an approach below MDA/MDH unless at least one of the following visual references for the intended runway is distinctly visible and identifiable to the pilot:

(i)

elements of the approach light system;

(ii)

the threshold;

(iii)

the threshold markings;

(iv)

the threshold lights;

(v)

the threshold identification lights;

(vi)

the visual glide slope indicator;

(vii)

the touchdown zone or touchdown zone markings;

(viii)

the touchdown zone lights;

(ix)

runway edge lights; or

(x)

other visual references accepted by the Authority.

System minima

Facility | Lowest DH/MDH

Localiser with or without DME | 250 ft

SRA (terminating at 1/2 NM) | 250 ft

SRA (terminating at 1 NM) | 300 ft

SRA (terminating at 2 NM or more) | 350 ft

RNAV/LNAV | 300 ft

VOR | 300 ft

VOR/DME | 250 ft

NDB | 350 ft

NDB/DME | 300 ft

VDF | 350 ft

(c)

Criteria for establishing RVR/Converted Met Visibility (Ref Table 6)

1.

In order to qualify for the lowest allowable values of RVR/CMV detailed in Table 6 (applicable to each approach grouping) the instrument approach shall meet at least the following facility requirements and associated conditions:

(i)

Instrument approaches with designated vertical profile up to and including 4,5° for Category A and B aeroplanes, or 3,77° for Category C and D aeroplanes, unless other approach angles are approved by the Authority, where the facilities are:

(A) ILS/MLS/GLS/PAR; or

(B) APV; and

where the final approach track is offset by not more than 15° for Category A and B aeroplanes or by not more than 5° for Category C and D aeroplanes.

(ii)

Instrument approaches flown using the CDFA technique with a nominal vertical profile, up to and including 4,5° for Category A and B aeroplanes, or 3,77° for Category C and D aeroplanes, unless other approach angles are approved by the Authority where the facilities are NDB, NDB/DME, VOR, VOR/DME, LLZ, LLZ/DME, VDF, SRA or RNAV/LNAV, with a final-approach segment of at least 3NM, which also fulfil the following criteria:

(A) The final approach track is offset by not more than 15° for Category A and B aeroplanes or by not more than 5° for Category C and D aeroplanes; and

(B) The FAF or another appropriate fix where descent is initiated is available, or distance to THR is available by FMS/RNAV or DME; and

(C) If the MAPt is determined by timing, the distance from FAF to THR is ≤ 8 NM.

(iii)

Instrument approaches where the facilities are NDB, NDB/DME, VOR, VOR/DME, LLZ, LLZ/DME, VDF, SRA or RNAV/LNAV, not fulfilling the criteria in paragraph (c)1.(ii) above, or with an MDH ≥ 1200 ft.

2.

The missed approach, after an approach has been flown using the CDFA technique, shall be executed when reaching the decision altitude (height) or the MAPt, whichever occurs first. The lateral part of the missed approach procedure must be flown via the MAPt unless otherwise stated on the approach chart.

(d)

Determination of RVR/CMV/Visibility minima for Category I, APV and non-precision approach operations

1.

The minimum RVR/CMV/Visibility shall be the highest of the values derived from Table 5 or Table 6 but not greater than the maximum values shown in Table 6 where applicable

2.

The values in Table 5 are derived from the formula below.

Required RVR/visibility (m) = [(DH/MDH (ft) × 0,3048)/tanα] – length of approach lights (m)

Note 1: α is the calculation angle, being a default value of 3,00 degrees increasing in steps

3.

With the approval of the Authority, the formula may be used with the actual approach slope and/or the actual length of the approach lights for a particular runway.

4.

If the approach is flown with a level flight segment at or above MDA/H, 200 metres shall be added for Cat A and B aeroplane and 400 metres for Cat C and D aeroplane to the minimum RVR/CMV value resulting from the application of Tables 5 and 6.

Note: The added value corresponds to the time/distance required to establish the aeroplane on the final descent.

5.

An RVR of less than 750 m as indicated in Table 5 may be used:

(i)

for Category I approach operations to runways with FALS (see below), Runway Touchdown Zone Lights (RTZL) and Runway Centreline Lights (RCLL) provided that the DH is not more than 200 ft; or

(ii)

for Category I approach operations to runways without RTZL and RCLL when using an approved HUDLS, or equivalent approved system, or when conducting a coupled approach or flight-director-flown approach to a DH equal to or greater than 200 ft. The ILS must not be promulgated as a restricted facility; or

(iii)

for APV approach operations to runways with FALS, RTZL and RCLL when using an approved HUD.

6.

The Authority may approve RVR values lower than those given in Table 5, for HUDLS and auto-land operations in accordance with paragraph (e) of this Appendix.

7.

The visual aids comprise standard runway day markings and approach and runway lighting (runway edge lights, threshold lights, runway end lights and in some cases also touch-down zone and/or runway centre line lights). The approach light configurations acceptable are classified and listed in Table 4 below.

8.

Notwithstanding the requirements in paragraph (d)7. above, the authority may approve that RVR values relevant to a Basic Approach Lighting System (BALS) are used on runways where the approach lights are restricted in length below 210m due to terrain or water, but where at least one cross-bar is available.

9.

For night operations or for any operation where credit for runway and approach lights is required, the lights must be on and serviceable except as provided for in Table 6a.

OPS Class of Facility | Length, configuration and intensity of approach lights

FALS (full approach light system) | ICAO: Precision approach CAT I Lighting System (HIALS 720 m ≥) distance coded centreline, Barrette centreline

IALS (intermediate approach light system) | ICAO: Simple approach lighting system (HIALS 420-719 m) single source, Barrette

BALS (basic approach light system) | Any other approach lighting System (HIALS, MIALS or ALS 210-419 m

NALS (no approach light system) | Any other approach lighting system (HIALS, MIALS or ALS < 210 m) or no approach lights

DH or MDH | Class of Lighting Facility

FALS | IALS | BALS | NALS

See paragraphs (d)5, (d)6 and (d)10 about RVR < 750 m

Feet | Metres

200 | — | 210 | 550 | 750 | 1000 | 1200

211 | — | 220 | 550 | 800 | 1000 | 1200

221 | — | 230 | 550 | 800 | 1000 | 1200

231 | — | 240 | 550 | 800 | 1000 | 1200

241 | — | 250 | 550 | 800 | 1000 | 1300

251 | — | 260 | 600 | 800 | 1100 | 1300

261 | — | 280 | 600 | 900 | 1100 | 1300

281 | — | 300 | 650 | 900 | 1200 | 1400

301 | — | 320 | 700 | 1000 | 1200 | 1400

321 | — | 340 | 800 | 1100 | 1300 | 1500

341 | — | 360 | 900 | 1200 | 1400 | 1600

361 | — | 380 | 1000 | 1300 | 1500 | 1700

381 | — | 400 | 1100 | 1400 | 1600 | 1800

401 | — | 420 | 1200 | 1500 | 1700 | 1900

421 | — | 440 | 1300 | 1600 | 1800 | 2000

441 | — | 460 | 1400 | 1700 | 1900 | 2100

461 | — | 480 | 1500 | 1800 | 2000 | 2200

481 | | 500 | 1500 | 1800 | 2100 | 2300

501 | — | 520 | 1600 | 1900 | 2100 | 2400

521 | — | 540 | 1700 | 2000 | 2200 | 2400

541 | — | 560 | 1800 | 2100 | 2300 | 2500

561 | — | 580 | 1900 | 2200 | 2400 | 2600

581 | — | 600 | 2000 | 2300 | 2500 | 2700

601 | — | 620 | 2100 | 2400 | 2600 | 2800

621 | — | 640 | 2200 | 2500 | 2700 | 2900

641 | — | 660 | 2300 | 2600 | 2800 | 3000

661 | — | 680 | 2400 | 2700 | 2900 | 3100

681 | — | 700 | 2500 | 2800 | 3000 | 3200

701 | — | 720 | 2600 | 2900 | 3100 | 3300

721 | — | 740 | 2700 | 3000 | 3200 | 3400

741 | — | 760 | 2700 | 3000 | 3300 | 3500

761 | — | 800 | 2900 | 3200 | 3400 | 3600

801 | — | 850 | 3100 | 3400 | 3600 | 3800

851 | — | 900 | 3300 | 3600 | 3800 | 4000

901 | — | 950 | 3600 | 3900 | 4100 | 4300

951 | — | 1000 | 3800 | 4100 | 4300 | 4500

1001 | — | 1100 | 4100 | 4400 | 4600 | 4900

1101 | — | 1200 | 4600 | 4900 | 5000 | 5000

1201 and above | 5000 | 5000 | 5000 | 5000

Facility/conditions | RVR/CMV (m) | Aeroplane category

A | B | C | D

ILS, MLS, GLS, PAR and APV | Min | According to Table 5

Max | 1500 | 1500 | 2400 | 2400

NDB, NDB/DME, VOR, VOR/DME, LLZ, LLZ/DME, VDF, SRA, RNAV/LNAV with a procedure which fulfils the criteria in paragraph (c)1.(ii): | Min | 750 | 750 | 750 | 750

Max | 1500 | 1500 | 2400 | 2400

For NDB, NDB/DME, VOR, VOR/DME, LLZ, LLZ/DME, VDF, SRA, RNAV/LNAV:

–

not fulfilling the criteria in paragraph (c)1.(ii) above, or

–

with a DH or MDH ≥ 1200 ft

Min | 1000 | 1000 | 1200 | 1200

Max | According to Table 5 if flown using the CDFA technique, otherwise an add-on of 200/400 m applies to the values in Table 5 but not to result in a value exceeding 5000 m.

Note 1: Conditions applicable to Table 6a:

(a)

multiple failures of runway lights other than indicated in Table 6a are not acceptable.

(b)

deficiencies of approach and runway lights are treated separately.

(c)

Category II or III operations. A combination of deficiencies in runway lights and RVR assessment equipment is not allowed.

(d)

failures other than ILS affect RVR only and not DH.

Note 2: For CAT IIIB operations with no DH, an operator shall ensure that, for aeroplanes authorised to conduct no DH operations with the lowest RVR limitations, the following applies in addition to the content of Table 6a:

(a)

RVR. At least one RVR value must be available at the aerodrome;

(b)

runway lights

(i)

no runway edge lights, or no centre lights — Day — RVR 200 m; night — not allowed;

(ii)

no TDZ lights — no restrictions;

(iii)

no standby power to runway lights — Day — RVR 200 m; night — not allowed.

Failed or downgraded equipment

(Note 1)

Effect on landing minima

CAT IIIB

(Note 2)

CAT IIIA | CAT II | CAT I | Non precision

ILS stand-by transmitter | Not allowed | No effect

Outer Marker | No effect if replaced by published equivalent position | Not applicable

Middle marker | No effect | No effect unless used as MAPT

Touchdown zone RVR assessment system | May be temporarily replaced with midpoint RVR if approved by the State of the aerodrome. RVR may be reported by human observation | No effect

Midpoint or stopend RVR | No effect

Anemometer for runway in use | No effect if other ground source available

Celiometer | No effect

Approach lights | Not allowed for operations with DH > 50 ft | Not allowed | minima as for nil facilities

Approach lights except the last 210 m | No effect | Not allowed | minima as for nil facilities

Approach lights except the last 420 m | No effect | minima as for intermediate facilities

Standby power for approach lights | No effect

Whole runway light system | Not allowed |

Day — minima as for nil facilities

Night — Not allowed

Edge lights | Day only; Night — not allowed

Centreline lights |

Day — RVR 300m

Night — not allowed

Day — RVR 300 m

Night — 550 m

No effect

Centreline lights spacing increased to 30 m | RVR 150m | No effect

Touchdown zone lights |

Day — RVR 200 m

Night — 300 m

Day — RVR 300 m

Night — 550 m

No effect

Standby power for runway lights | Not allowed | No effect

Taxiway light system | No effect — except delays due to reduced movement rate

10.

Single pilot operations. For single pilot operations, an operator must calculate the minimum RVR/visibility for all approaches in accordance with OPS 1.430 and this Appendix.

(i)

An RVR of less than 800 metres as indicated in Table 5 may be used for Category I approaches provided any of the following is used at least down to the applicable DH:

(A) a suitable autopilot, coupled to an ILS or MLS which is not promulgated as restricted; or

(B) an approved HUDLS (including, where appropriate, EVS), or equivalent approved system.

(ii)

Where RTZL and/or RCLL are not available, the minimum RVR/CMV shall not be less than 600 m.

(iii)

An RVR of less than 800 metres as indicated in Table 5 may be used for APV operations to runways with FALS, RTZL and RCLL when using an approved HUDLS, or equivalent approved system, or when conducting a coupled approach to a DH equal to or greater than 250 ft.

(e)

Lower than Standard Category I Operations

1.

Decision height.

A lower than Standard Category I Operation decision height must not be lower than:

(i)

the minimum decision height specified in the AFM, if stated; or

(ii)

the minimum height to which the precision approach aid can be used without the required visual reference; or

(iii)

the OCH for the category of aeroplane; or

(iv)

the decision height to which the flight crew is authorised to operate; or

(v)

200 ft.

whichever is higher.

2.

Type of facility.

An ILS/MLS which supports a lower than Standard Category I operation must be an unrestricted facility with a straight-in course (≤ 3o offset) and the ILS must be certificated to:

(i)

Class I/T/1 for operations to a minimum of 450m RVR; or

(ii)

Class II/D/2 for operations to less than 450m RVR.

Single ILS facilities are only acceptable if Level 2 performance is provided.

3.

Required RVR/CMV.

The lowest minima to be used by an operator for lower than Standard Category I operations are stipulated in Table 6b below:

Note 1: The visual aids comprise standard runway day markings, approach lighting, runway edge lights, threshold lights, runway end lights and, for operations below 450m, shall include touch-down zone and/or runway centre line lights.

Lower than Standard Category I minima

DH(ft) | Class of lighting facility

FALS | IALS | BALS | NALS

RVR/CMV (metres)

200 | — | 210 | 400 | 500 | 600 | 750

211 | — | 220 | 450 | 550 | 650 | 800

221 | — | 230 | 500 | 600 | 700 | 900

231 | — | 240 | 500 | 650 | 750 | 1000

241 | — | 249 | 550 | 700 | 800 | 1100

4.

Visual reference. A pilot shall not continue an approach below decision height unless visual reference containing a segment of at least three consecutive lights being the centre line of the approach lights, or touchdown zone lights, or runway centre line lights, or runway edge lights, or a combination of these is attained and can be maintained. This visual reference must include a lateral element of the ground pattern, i.e. an approach lighting crossbar or the landing threshold or a barrette of the touchdown zone lighting unless the operation is conducted utilising an approved HUDLS usable to at least 150 ft.

5.

Approval.

To conduct lower than Standard Category I operations:

(i)

the approach shall be flown auto-coupled to an auto-land; or an approved HUDLS shall be used to at least 150 ft above the threshold.

(ii)

the aeroplane shall be certificated in accordance with CS-AWO to conduct Category II operations;

(iii)

the auto-land system shall be approved for Category IIIA operations;

(iv)

in service proving requirements shall be completed in accordance with Appendix 1 to OPS 1.440 paragraph (h);

(v)

training specified in Appendix 1 to OPS 1.450 paragraph (h) shall be completed, this shall include training and checking in a Flight Simulator using the appropriate ground and visual aids at the lowest applicable RVR;

(vi)

the Operator must ensure that Low Visibility procedures are established and in operation at the intended aerodrome of landing; and

(vii)

the Operator shall be approved by the Authority.

(f)

Precision approach — Category II and other than Standard Category II operations

1.

General.

(i)

A Category II operation is a precision instrument approach and landing using ILS or MLS with:

(A) A decision height below 200 ft but not lower than 100 ft; and

(B) A runway visual range of not less than 300 m.

(ii)

An other than Standard Category II operation is a precision instrument approach and landing using ILS or MLS which meets facility requirements as established in paragraph (iii) below with:

(A) A decision height below 200 ft but not lower than 100 ft; (See Table 7b below) and

(B) A runway visual range of not less than 350/400 m. (See Table 7b below)

(iii)

The ILS/MLS that supports other than a Standard Category II operation shall be an unrestricted facility with a straight in course (≤ 3o offset) and the ILS shall be certificated to:

(A) Class I/T/1 for operations down to 450m RVR and to a DH of 200 ft or more; or,

This article is long: the rest is at the official publication.