10 SUBPART D OPERATIONAL PROCEDURES, Commission Regulation (EC) No 859/2008 of 20 August 2008 amending Council Regulation (EE…

In forcesince 20 Aug 2008

The terms which are listed below are for use within the context of this regulation.

(a)

Adequate Aerodrome. An aerodrome which the operator considers to be satisfactory, taking account of the applicable performance requirements and runway characteristics; at the expected time of use, the aerodrome will be available and equipped with necessary ancillary services such as ATS, sufficient lighting, communications, weather reporting, navaids and emergency services.

(b)

ETOPS (Extended range operations for two engine aeroplanes). ETOPS operations are those with two engine aeroplanes approved by the Authority (ETOPS approval), to operate beyond the threshold distance determined in accordance with OPS 1.245 (a) from an Adequate Aerodrome.

(c)

Adequate ETOPS en-route alternate aerodrome. An adequate aerodrome, which additionally, at the expected time of use, has an ATS facility and at least one instrument approach procedure.

(d)

En-route alternate (ERA) aerodrome. An adequate aerodrome along the route, which may be required at the planning stage.

(e)

3 % ERA. An en-route alternate aerodrome selected for the purposes of reducing contingency fuel to 3 %.

(f)

Isolated aerodrome. If acceptable to the Authority, the destination aerodrome can be considered as an isolated aerodrome, if the fuel required (diversion plus final) to the nearest adequate destination alternate aerodrome is more than:

For aeroplanes with reciprocating engines, fuel to fly for 45 minutes plus 15 % of the flight time planned to be spent at cruising level or two hours, whichever is less; or

For aeroplanes with turbine engines, fuel to fly for two hours at normal cruise consumption above the destination aerodrome, including final reserve fuel.

(g)

Equivalent position. A position that can be established by means of a DME distance, a suitably located NDB or VOR, SRE or PAR fix or any other suitable fix between three and five miles from threshold that independently establishes the position of the aeroplane.

(h)

Critical phases of flight. Critical phases of flight are the take-off run, the take-off flight path, the final approach, the landing, including the landing roll, and any other phases of flight at the discretion of the commander.

(i)

Contingency fuel. The fuel required to compensate for unforeseen factors which could have an influence on the fuel consumption to the destination aerodrome such as deviations of an individual aeroplane from the expected fuel consumption data, deviations from forecast meteorological conditions and deviations from planned routings and/or cruising levels/altitudes.

(j)

Separate runways. Runways at the same aerodrome that are separate landing surfaces. These runways may overlay or cross in such a way that if one of the runways is blocked, it will not prevent the planned type of operations on the other runway. Each runway shall have a separate approach procedure based on a separate navigation aid.

(k)

Approved one-engine-inoperative cruise speed. For ETOPS, the approved one-engine-inoperative cruise speed for the intended area of operation shall be a speed, within the certified limits of the aeroplane, selected by the operator and approved by the regulatory authority.

(l)

ETOPS area. An ETOPS area is an area containing airspace within which an ETOPS approved aeroplane remains in excess of the specified flying time in still air (in standard conditions) at the approved one-engine-inoperative cruise speed from an adequate ETOPS route alternate aerodrome.

(m)

Dispatch. ETOPS planning minima applies until dispatch. Dispatch is when the aircraft first moves under its own power for the purpose of taking off.

An operator shall:

(a)

Establish and maintain a method of exercising operational control approved by the Authority; and

(b)

Exercise operational control over any flight operated under the terms of his AOC.

An operator shall provide an Operations Manual in accordance with Subpart P for the use and guidance of operations personnel.

An operator shall ensure that all personnel assigned to, or directly involved in, ground and flight operations are properly instructed, have demonstrated their abilities in their particular duties and are aware of their responsibilities and the relationship of such duties to the operation as a whole.

(a)

An operator shall establish procedures and instructions, for each aeroplane type, containing ground staff and crew members' duties for all types of operation on the ground and in flight.

(b)

An operator shall establish a check-list system to be used by crew members for all phases of operation of the aeroplane under normal, abnormal and emergency conditions as applicable, to ensure that the operating procedures in the Operations Manual are followed.

(c)

An operator shall not require a crew member to perform any activities during critical phases of the flight other than those required for the safe operation of the aeroplane (see OPS 1.192).

An operator shall ensure that air traffic services are used for all flights whenever available.

An operator shall ensure that his in-flight operational instructions involving a change to the air traffic flight plan shall, when practicable, be coordinated with the appropriate air traffic service unit before transmission to an aeroplane.

An operator shall only authorise use of aerodromes that are adequate for the type(s) of aeroplane and operation(s) concerned.

(a)

An operator shall specify aerodrome operating minima, established in accordance with OPS 1.430 for each departure, destination or alternate aerodrome authorised to be used in accordance with OPS 1.220.

(b)

Any increment imposed by the Authority must be added to the minima specified in accordance with subparagraph (a) above.

(c)

The minima for a specific type of approach and landing procedure are considered applicable if:

1.

The ground equipment shown on the respective chart required for the intended procedure is operative;

2.

The aeroplane systems required for the type of approach are operative;

3.

The required aeroplane performance criteria are met; and

4.

Crew is qualified accordingly.

(a)

An operator shall ensure that instrument departure and approach procedures established by the State in which the aerodrome is located are used.

(b)

Notwithstanding subparagraph (a) above, a commander may accept an ATC clearance to deviate from a published departure or arrival route, provided obstacle clearance criteria are observed and full account is taken of the operating conditions. The final approach must be flown visually or in accordance with the established instrument approach procedure.

(c)

Different procedures to those required to be used in accordance with subparagraph (a) above may only be implemented by an operator provided they have been approved by the State in which the aerodrome is located, if required, and accepted by the Authority.

An operator shall establish appropriate operating departure and arrival/approach procedures for each aircraft type in accordance with the following:

(a)

The operator shall ensure that safety has priority over noise abatement, and

(b)

These procedures shall be designed to be simple and safe to operate with no significant increase in crew workload during critical phases of flight, and

(c)

For each aeroplane type two departure procedures shall be defined, in accordance with ICAO Doc. 8168 (Procedures for air navigation services, “PANS-OPS”), Volume I:

1.

noise abatement departure procedure one (NADP 1), designed to meet the close-in noise abatement objective; and

2.

noise abatement departure procedure two (NADP 2), designed to meet the distant noise abatement objective; and

3.

in addition, each NADP climb profile can only have one sequence of actions.

(a)

An operator shall ensure that operations are only conducted along such routes or within such areas, for which:

1.

Ground facilities and services, including meteorological services, are provided which are adequate for the planned operation;

2.

The performance of the aeroplane intended to be used is adequate to comply with minimum flight altitude requirements;

3.

The equipment of the aeroplane intended to be used meets the minimum requirements for the planned operation;

4.

Appropriate maps and charts are available (OPS 1.135 (a)(9) refers);

5.

If two-engined aeroplanes are used, adequate aerodromes are available within the time/distance limitations of OPS 1.245;

6.

If single-engine aeroplanes are used, surfaces are available which permit a safe forced landing to be executed.

(b)

An operator shall ensure that operations are conducted in accordance with any restriction on the routes or the areas of operation, imposed by the Authority.

An operator shall not operate an aeroplane in defined portions of airspace where, based on regional air navigation agreement, a vertical separation minimum of 300 m (1000 ft) applies unless approved to do so by the Authority (RVSM Approval). (See also OPS 1.872).

(a)

An operator shall ensure that an aeroplane operated in areas, or through portions of airspace, or on routes where navigation performance requirements have been specified, is certified according to these requirements, and, if required, that the Authority has granted the relevant operational approval. (See also OPS 1.865 (c)(2), OPS 1.870 and OPS 1.872).

(b)

An operator of an aeroplane operating in areas referred to in (a) shall ensure that all contingency procedures, specified by the authority responsible for the airspace concerned, have been included in the Operations Manual.

(a)

Unless specifically approved by the Authority in accordance with OPS 1.246 (a) (ETOPS approval), an operator shall not operate a two-engined aeroplane over a route which contains a point further from an adequate aerodrome (under standard conditions in still air) than, in the case of:

1.

Performance Class A aeroplanes with either:

(i)

a maximum approved passenger seating configuration of 20 or more; or

(ii)

a maximum take-off mass of 45360 kg or more,

the distance flown in 60 minutes at the one-engine-inoperative cruise speed determined in accordance with subparagraph (b) below;

2.

Performance Class A aeroplanes with:

(i)

a maximum approved passenger seating configuration of 19 or less; and

(ii)

a maximum take-off mass less than 45360 kg,

the distance flown in 120 minutes or, if approved by the Authority, up to 180 minutes for turbo-jet aeroplanes, at the one-engine-inoperative cruise speed determined in accordance with subparagraph (b) below;

3.

Performance Class B or C aeroplanes:

(i)

The distance flown in 120 minutes at the one-engine-inoperative cruise speed determined in accordance with subparagraph (b) below; or

(ii)

300 nautical miles, whichever is less.

(b)

An operator shall determine a speed for the calculation of the maximum distance to an adequate aerodrome for each two-engined aeroplane type or variant operated, not exceeding VMO, based upon the true airspeed that the aeroplane can maintain with one-engine-inoperative.

(c)

An operator must ensure that the following data, specific to each type or variant, is included in the Operations Manual:

1.

the one-engine-inoperative cruise speed determined in accordance with subparagraph (b) above; and

2.

the maximum distance from an adequate aerodrome determined in accordance with subparagraphs (a) and (b) above.

Note: The speeds specified above are only intended to be used for establishing the maximum distance from an adequate aerodrome.

(a)

An operator shall not conduct operations beyond the threshold distance determined in accordance with OPS 1.245 unless approved to do so by the Authority (ETOPS approval).

(b)

Prior to conducting an ETOPS flight, an operator shall ensure that an adequate ETOPS en-route alternate is available, within either the operator's approved diversion time, or a diversion time based on the MEL generated serviceability status of the aeroplane, whichever is shorter. (See also OPS 1.297 (d)).

(a)

An operator shall establish minimum flight altitudes and the methods to determine those altitudes for all route segments to be flown which provide the required terrain clearance taking into account the requirements of Subparts F to I.

(b)

Every method for establishing minimum flight altitudes must be approved by the Authority.

(c)

Where minimum flight altitudes established by States overflown are higher than those established by the operator, the higher values shall apply.

(d)

An operator shall take into account the following factors when establishing minimum flight altitudes:

1.

The accuracy with which the position of the aeroplane can be determined;

2.

The probable inaccuracies in the indications of the altimeters used;

3.

The characteristics of the terrain (e.g. sudden changes in the elevation) along the routes or in the areas where operations are to be conducted;

4.

The probability of encountering unfavourable meteorological conditions (e.g. severe turbulence and descending air currents); and

5.

Possible inaccuracies in aeronautical charts.

(e)

In fulfilling the requirements prescribed in subparagraph (d) above due consideration shall be given to:

1.

Corrections for temperature and pressure variations from standard values;

2.

The ATC requirements; and

3.

Any foreseeable contingencies along the planned route.

(a)

An operator must establish a fuel policy for the purpose of flight planning and in-flight re-planning to ensure that every flight carries sufficient fuel for the planned operation and reserves to cover deviations from the planned operation.

(b)

An operator shall ensure that the planning of flights is at least based upon 1. and 2. below:

1.

Procedures contained in the Operations Manual and data derived from:

(i)

data provided by the aeroplane manufacturer; or

(ii)

current aeroplane specific data derived from a fuel consumption monitoring system.

2.

The operating conditions under which the flight is to be conducted including:

(i)

realistic aeroplane fuel consumption data;

(ii)

anticipated masses;

(iii)

expected meteorological conditions; and

(iv)

air navigation services provider(s) procedures and restrictions.

(c)

An operator shall ensure that the pre-flight calculation of usable fuel required for a flight includes:

1.

Taxi fuel; and

2.

Trip fuel; and

3.

Reserve fuel consisting of:

(i)

contingency fuel (see OPS 1.192); and

(ii)

alternate fuel, if a destination alternate aerodrome is required. (This does not preclude selection of the departure aerodrome as the destination alternate aerodrome); and

(iii)

final reserve fuel; and

(iv)

additional fuel, if required by the type of operation (e.g. ETOPS); and

4.

extra fuel if required by the commander.

(d)

An operator shall ensure that in-flight re-planning procedures for calculating usable fuel required when a flight has to proceed along a route or to a destination aerodrome other than originally planned includes:

1.

trip fuel for the remainder of the flight; and

2.

reserve fuel consisting of:

(i)

contingency fuel; and

(ii)

alternate fuel, if a destination alternate aerodrome is required (this does not preclude selection of the departure aerodrome as the destination alternate aerodrome); and

(iii)

final reserve fuel; and

(iv)

additional fuel, if required by the type of operation (e.g. ETOPS); and

3.

extra fuel if required by the commander.

(a)

An operator shall establish procedures for the carriage of persons with reduced mobility (PRMs).

(b)

An operator shall ensure that PRMs are not allocated, nor occupy, seats where their presence could:

1.

impede the crew in their duties;

2.

obstruct access to emergency equipment; or

3.

impede the emergency evacuation of the aeroplane.

(c)

The commander must be notified when PRMs are to be carried on board.

An operator shall establish procedures for the transportation of inadmissible passengers, deportees or persons in custody to ensure the safety of the aeroplane and its occupants. The commander must be notified when the above-mentioned persons are to be carried on board.

(a)

An operator shall establish procedures to ensure that only such hand baggage is taken into the passenger cabin as can be adequately and securely stowed.

(b)

An operator shall establish procedures to ensure that all baggage and cargo on board, which might cause injury or damage, or obstruct aisles and exits if displaced, is placed in stowages designed to prevent movement.

An operator shall establish procedures to ensure that passengers are seated where, in the event that an emergency evacuation is required, they may best assist and not hinder evacuation from the aeroplane.

An operator shall ensure that:

(a)

General

1.

Passengers are given a verbal briefing about safety matters. Parts or all of the briefing may be provided by an audio-visual presentation.

2.

Passengers are provided with a safety briefing card on which picture type instructions indicate the operation of emergency equipment and exits likely to be used by passengers.

(b)

Before take-off

1.

Passengers are briefed on the following items if applicable:

(i)

smoking regulations;

(ii)

back of the seat to be in the upright position and tray table stowed;

(iii)

location of emergency exits;

(iv)

location and use of floor proximity escape path markings;

(v)

stowage of hand baggage;

(vi)

restrictions on the use of portable electronic devices; and

(vii)

the location and the contents of the safety briefing card; and,

2.

Passengers receive a demonstration of the following:

(i)

the use of safety belts and/or safety harnesses, including how to fasten and unfasten the safety belts and/or safety harnesses;

(ii)

the location and use of oxygen equipment if required (OPS 1.770 and OPS 1.775 refer). Passengers must also be briefed to extinguish all smoking materials when oxygen is being used; and

(iii)

the location and use of life jackets if required (OPS 1.825 refers).

(c)

After take-off

1.

Passengers are reminded of the following if applicable:

(i)

smoking regulations; and

(ii)

use of safety belts and/or safety harnesses including the safety benefits of having safety belts fastened when seated irrespective of seat belt sign illumination.

(d)

Before landing

1.

Passengers are reminded of the following if applicable:

(i)

smoking regulations;

(ii)

use of safety belts and/or safety harnesses;

(iii)

back of the seat to be in the upright position and tray table stowed;

(iv)

re-stowage of hand baggage; and

(v)

restrictions on the use of portable electronic devices.

(e)

After landing

1.

Passengers are reminded of the following:

(i)

smoking regulations; and

(ii)

use of safety belts and/or safety harnesses.

(f)

In an emergency during flight, passengers are instructed in such emergency action as may be appropriate to the circumstances.

(a)

An operator shall ensure that an operational flight plan is completed for each intended flight.

(b)

The commander shall not commence a flight unless he/she is satisfied that:

1.

the aeroplane is airworthy;

2.

the aeroplane is not operated contrary to the provision of the configuration deviation list (CDL);

3.

the instruments and equipment required for the flight to be conducted, in accordance with Subparts K and L, are available;

4.

the instruments and equipment are in operable condition except as provided in the MEL;

5.

those parts of the operations manual which are required for the conduct of the flight are available;

6.

the documents, additional information and forms required to be available by OPS 1.125 and OPS 1.135 are on board;

7.

current maps, charts and associated documentation or equivalent data are available to cover the intended operation of the aeroplane including any diversion which may reasonably be expected. This shall include any conversion tables necessary to support operations where metric heights, altitudes and flight levels must be used;

8.

ground facilities and services required for the planned flight are available and adequate;

9.

the provisions specified in the operations manual in respect of fuel, oil and oxygen requirements, minimum safe altitudes, aerodrome operating minima and availability of alternate aerodromes, where required, can be complied with for the planned flight;

10.

the load is properly distributed and safely secured;

11.

the mass of the aeroplane, at the commencement of take-off roll, will be such that the flight can be conducted in compliance with Subparts F to I as applicable; and

12.

any operational limitation in addition to those covered by subparagraphs 9 and 11 above can be complied with.

(a)

An operator shall establish procedures for the selection of destination and/or alternate aerodromes in accordance with OPS 1.220 when planning a flight.

(b)

An operator must select and specify in the operational flight plan a take-off alternate aerodrome if it would not be possible to return to the departure aerodrome for meteorological or performance reasons. The take-off alternate aerodrome, in relation to the departure aerodrome, shall be located within:

1.

for two-engined aeroplanes, either:

(i)

one hour flight time at a one-engine-inoperative cruising speed according to the Aircraft Flight Manual (AFM) in still air standard conditions based on the actual take-off mass; or

(ii)

the operator's approved ETOPS diversion time, subject to any MEL restriction, up to a maximum of two hours, at the one-engine-inoperative cruising speed according to the AFM in still air standard conditions based on the actual take-off mass for aeroplanes and crews authorised for ETOPS; or

2.

two hours flight time at a one-engine-inoperative cruising speed according to the AFM in still air standard conditions based on the actual take-off mass for three and four-engined aeroplanes; and

3.

if the AFM does not contain a one-engine-inoperative cruising speed, the speed to be used for calculation must be that which is achieved with the remaining engine(s) set at maximum continuous power.

(c)

An operator must select at least one destination alternate for each IFR flight unless:

1.

both:

(i)

the duration of the planned flight from take-off to landing or, in the event of in-flight re-planning in accordance with OPS 1.255(d), the remaining flying time to destination does not exceed six hours, and

(ii)

two separate runways (see OPS 1.192) are available and usable at the destination aerodrome and the appropriate weather reports or forecasts for the destination aerodrome, or any combination thereof, indicate that for the period from one hour before until one hour after the expected time of arrival at the destination aerodrome, the ceiling will be at least 2000 ft or circling height +500 ft, whichever is greater, and the visibility will be at least 5 km;

or

2.

the destination aerodrome is isolated.

(d)

An operator must select two destination alternate aerodromes when:

1.

the appropriate weather reports or forecasts for the destination aerodrome, or any combination thereof, indicate that during a period commencing one hour before and ending one hour after the estimated time of arrival, the weather conditions will be below the applicable planning minima (see OPS 1.297(b)); or

This article is long: the rest is at the official publication.