33 ANNEX XIII EMISSION TYPE-APPROVAL OF REPLACEMENT POLLUTION CONTROL DEVICES AS SEPARATE TECHNICAL UNIT, Regulation (EU) 2025/1706

In forcesince 23 Jul 2026

1.1. This Annex contains additional requirement for the type-approval as separate technical units of pollution control devices.

2.1. Marking

Original replacement pollution control devices shall bear at least the following identifications:

(a)

the vehicle manufacturer’s name or trade mark;

(b)

the make and identifying part number of the original replacement pollution control device as recorded in the information mentioned in point 2.3.

2.2. Documentation

Original replacement pollution control devices shall be accompanied by the following information:

(a)

the vehicle manufacturer’s name or trade mark;

(b)

the make and identifying part number of the original replacement pollution control device as recorded in the information mentioned in point 2.3;

(c)

the vehicles for which the original replacement pollution control device is of a type covered by point 2.3 of the Addendum to Appendix 4 to Annex I, including, where applicable, a marking to identify if the original replacement pollution control device is suitable for fitting to a vehicle that is equipped with an on-board diagnostic (OBD) system;

(d)

installation instructions, where necessary.

This information shall be available in the product catalogue distributed to points of sale by the vehicle manufacturer.

2.3. The vehicle manufacturer shall provide to the technical service and/or approval authority the necessary information in electronic format which makes the link between the relevant part numbers and the type-approval documentation.

This information shall contain the following:

(a)

make(s) and type(s) of vehicle,

(b)

make(s) and type(s) of original replacement pollution control device,

(c)

part number(s) of original replacement pollution control device,

(d)

type-approval number of the relevant vehicle type(s) with regard to emissions.

3.1. Every replacement pollution control device conforming to the type approved under this Regulation as a separate technical unit shall bear an EU type-approval mark.

3.2. This mark shall consist of a rectangle surrounding the lower-case letter ‘e’ followed by the distinguishing number of the Member State which has granted the EU type-approval in accordance with the numbering system set out in Regulation (EU) 2020/683.

The EU type-approval mark shall also include in the vicinity of the rectangle the ‘base approval number’ contained in section 4 of the type-approval number referred to in Annex IV to Regulation (EU) 2020/683, preceded by the two figures indicating the sequence number assigned to the latest major technical amendment to this Regulation on the date EU type-approval for a separate technical unit was granted. For this Regulation, the sequence number is 00.

3.3. The EU type-approval mark shall be affixed to the replacement pollution control device in such a way as to be clearly legible and indelible. It shall, wherever possible, be visible when the replacement pollution control device is installed on the vehicle.

3.4. Appendix 3 to this Annex gives an example of the EU type-approval mark.

4.1. The requirements for the type-approval of replacement pollution control devices shall be those of Section 5 of UN Regulation No 103 with the exceptions set out in sections 4.1.1 to 4.1.4.

4.1.1. Reference to the ‘test cycle’ in Section 5 of UN Regulation No 103 shall be understood as being the same Type 1 test and Type 1 test cycle as used for the original type-approval of the vehicle.

4.1.2. The terms ‘catalytic converter’ and ‘converter’ used in section 5 of UN Regulation No 103 shall be understood to mean ‘pollution control device’.

4.1.3. The regulated pollutants referred to throughout section 5.2.3 of UN Regulation No 103 shall be replaced by all the pollutants specified in Annex 1, Table 1 of Regulation (EU) 2024/1257 for replacement pollution control devices intended to be fitted to vehicles type approved to Regulation (EU) 2024/1257.

4.1.4. For replacement pollution control devices intended to be fitted to vehicles type approved to Regulation (EU) 2024/1257, the durability requirements and associated deterioration factors specified in section 5 of UN Regulation No 103, shall refer to those specified in Annex VII to this Regulation.

4.2. For vehicles with positive-ignition engines, if the NMHC emissions measured during the demonstration test of a new original equipment catalytic converter, under paragraph 5.2.1 of UN Regulation No 103, are higher than the values measured during the type-approval of the vehicle, the difference shall be added to the OBD thresholds. The OBD thresholds are specified in Table 4A of paragraph 6.8.2 of UN Regulation No 154.

4.3. The revised OBD thresholds will apply during the tests of OBD compatibility set out in paragraphs 5.5 to 5.5.5 of UN/ECE Regulation No 103. In particular, when the exceedance allowed in paragraph 1 of Appendix 1 to Annex C5 to UN Regulation No 154 is applied.

4.4. Requirements for replacement periodically regenerating systems

4.4.1. Requirements regarding emissions

4.4.1.1. The vehicle(s) indicated in Articles 13(3), (4) and (5), equipped with a replacement periodically regenerating system of the type for which approval is requested, shall be subject to the tests described in Appendix 1 to Annex B6 to UN Regulation No 154, in order to compare its performance with the same vehicle equipped with the original periodically regenerating system.

4.4.1.2. Reference to the ‘Type 1 test’ and ‘Type 1 test cycle’ in Appendix 1 to Annex B6 to UN Regulation No 154 and the ‘test cycle’ in Section 5 of UN Regulation No 103 shall be understood as being the same Type 1 test and Type 1 test cycle as used for the original type-approval of the vehicle.

4.4.2. Determination of the basis for comparison

4.4.2.1. The vehicle shall be fitted with a new original periodically regenerating system. The emissions performance of this system shall be determined following the test procedure set out in Appendix 1 to Annex B6 to UN Regulation No 154.

4.4.2.1.1. Reference to the ‘Type 1 test’ and ‘Type 1 test cycle’ in Appendix 1 to Annex B6 to UN Regulation No 154 and the ‘test cycle’ in Section 5 of UN Regulation No 103 shall be understood as being the same Type 1 test and Type 1 test cycle as used for the original type-approval of the vehicle.

4.4.2.2. Upon request of the applicant for the approval of the replacement component, the approval authority shall make available on a non- discriminatory basis, the information referred to in point 3.2.12.2.10.2 of the information document contained in Annex A1 of UN Regulation No 154 for each vehicle tested.

4.4.3. Exhaust gas test with a replacement periodically regeneration system

4.4.3.1. The original equipment periodically regenerating system of the test vehicle(s) shall be replaced by the replacement periodically regenerating system. The emissions performance of this system shall be determined following the test procedure set out in Appendix 1 to Annex B6 to UN Regulation No 154.

4.4.3.1.1. Reference to the ‘Type 1 test’ and ‘Type 1 test cycle’ in Appendix 1 to Annex B6 to UN Regulation No 154 and the ‘test cycle’ in Section 5 of UN Regulation No 103 shall be understood as being the same Type 1 test and Type 1 test cycle as used for the original type-approval of the vehicle.

4.4.3.2. To determine the D-factor of the replacement periodically regenerating system, any of the engine test bench methods referred to in Appendix 1 to Annex B6 to UN Regulation No 154 may be used.

4.4.4. Other requirements

The requirements provided in paragraphs 5.2.3, 5.3, 5.4 and 5.5 of UN Regulation No 103 shall apply to replacement periodically regenerating systems. In these paragraphs the words ‘catalytic converter’ shall be understood to mean ‘periodically regenerating system’. The exceptions provided in the paragraphs in section 4.1 of this Annex shall also apply to periodically regenerating systems.

5.1. Each replacement pollution control device shall be clearly and indelibly marked with the manufacturer’s name or trade mark and accompanied by the following information:

(a)

the vehicles (including year of manufacture) for which the re- placement pollution control device is approved, including, where applicable, a marking to identify if the replacement pollution control device is suitable for fitting to a vehicle that is equipped with an on-board diagnostic (OBD) system;

(b)

installation instructions, where necessary.

The information shall be available in the product catalogue distributed to points of sale by the manufacturer of replacement pollution control devices.

6.1. Measures to ensure the conformity of production shall be taken in accordance with the provisions laid down in Article 31 of Regulation (EU) 2018/858.

6.2. Special provisions

6.2.1. The checks referred to in point 3 of Annex IV to Regulation (EU) 2018/858 shall include compliance with the characteristics as defined under Article 3(5) of this Regulation.

6.2.2. For the application of Article 31(3) of Regulation (EU) 2018/858, the tests described in section 4.4.1 of this Annex and section 5.2 of UN/ECE Regulation No 103 (requirements regarding emissions) may be carried out. In this case, the holder of the approval may request, as an alternative, to use as a basis for comparison not the original equipment pollution control device, but the replacement pollution control device which was used during the type-approval tests (or another sample that has been proven to conform to the approved type). Emissions values measured with the sample under verification shall then on average not exceed by more than 15 % the mean values measured with the sample used for reference.