7 Addendum to EU type-approval certificate No … concerning the type-approval of a vehicle with regard to exhaust and evaporative emissions according to Regulation (EU) 2024/1257 and Regulation (EU) 2025/1706, Regulation (EU) 2025/1706

In forcesince 23 Jul 2026

The information laid down in the Addendum of Annex A2 to UN Regulation No 154, where applicable, shall be supplied.

Cross references to information in the Test Report or Information Document should be avoided when completing the type-approval certificate.

Additionally, the EU specific information in the following sections, where applicable, shall be supplied.

1.

Add the following point 0.2.

0.2. Base vehicle identifier (1)

2.

Add the following table to section 2.1 after the type 5 related sections (a)-(d):

Type 6 | CO (g/km) | THC (g/km)

Measured value | |

Limit value | |

3.

Add the following after section 2.5.1.4.1:

Repeat 2.5.1. in case of base vehicle.

4.

Add the following after section 2.5.3.8.3:

Repeat 2.5.3. in case of base vehicle.

5.

Add the following at the end of section 2.5.4:

Repeat 2.5.4. in case of base vehicle

6.

Add the following sections 2.6, 4 and 5 after section 2.5.5:

Decision approving the eco-innovation (10) | Code of the eco- innovation (11) | Type 1 cycle |

1.

CO2 emissions of the baseline vehicle (g/km)

2.

CO2 emissions of the eco-innovation vehicle (g/ km)

3.

CO2 emissions of the baseline vehicle under type 1 test-cycle (12)

4.

CO2 emissions of the eco-innovation vehicle under type 1 test-cycle

5.

Usage factor (UF) i.e. temporal share of technology usage in normal operation conditions

CO2 emissions savings

((1 - 2) - (3 - 4)) * 5

2025/1706 | | | | | | | |

Total CO2 emissions saving on WLTP (g/km) (13) |

4.

POWER MEASUREMENT

Maximum engine net power of internal combustion engine, net power and maximum 30 minutes power of electric drive train

4.1. Internal combustion engine net power

4.1.1. Engine speed (min–1) …

4.1.2. Measured fuel flow (g/h) …

4.1.3. Measured torque (Nm) …

4.1.4. Measured power (kW) …

4.1.5. Barometric pressure (kPa) …

4.1.6. Water vapour pressure (kPa) …

4.1.7. Intake air temperature (K) …

4.1.8. Power correction factor when applied …

4.1.9. Corrected power (kW) …

4.1.10. Auxiliary power (kW) …

4.1.11. Net power (kW) …

4.1.12. Net torque (Nm) …

4.1.13. Corrected specific fuel consumption (g/kWh) …

4.2. Electric drive train(s):

4.2.1. Declared figures

4.2.2. Maximum net power: … kW, at … min–1

4.2.3. Maximum net torque: … Nm, at … min–1

4.2.4. Maximum net torque at zero engine speed: … Nm

4.2.5. Maximum 30 minutes power: … kW

4.2.6. Essential characteristics of the electric drive train

4.2.7. Test DC voltage: … V

4.2.8. Working principle: …

4.2.9. Cooling system:

4.2.10. Motor: liquid/air (1)

4.2.11. Variator: liquid/air (1)

4.3. System Power (manufacturer’s declared values) (where applicable)

4.3.1. Peak Vehicle System Power: ... kW

4.3.2. Sustained Vehicle System Power: ... kW

5.

REMARKS: …

(1)

Delete where not applicable (there are cases where nothing needs to be deleted when more than one entry is applicable).

(2)

Reference to Regulation (EU) 2024/1257.

(3)

Reference to this Regulation, Implementing Regulation (EU) 2025/1706.

(4)

If the means of identification of type contains characters not relevant to describe the vehicle, component or separate technical unit types covered by this information, such characters shall be represented in the documentation by the symbol ‘?’ (e.g. ABC??123??).

(5)

As defined in Article 4 of Regulation (EU) 2018/858.

(6)

As defined in Article 3(24) of Regulation (EU) 2018/858.

(7)

As referred to in Article 26(4) of Regulation (EU) 2018/858.

(8)

Repeat the table for each reference fuel tested.

(9)

Expand the table if necessary, using one extra row per eco-innovation.

(10)

Number of the Commission Decision approving the eco-innovation.

(11)

Assigned in the Commission Decision approving the eco-innovation.

(12)

If modelling is applied instead of the Type 1 test-cycle, this value shall be the one provided by the modelling methodology.

(13)

Sum of the emissions saving of each individual eco-innovation on Type 1

(14)

The general code of the eco-innovation(s) shall consist of the following elements, each separated by a blank space:

Section 1 as set out in Annex IV to Regulation (EU) 2018/858;

Individual code of each eco-innovation fitted in the vehicle, indicated in chronological order of the Commission approval decisions.

(E.g. the general code of three eco-innovations approved chronologically as 10, 15 and 16 and fitted to a vehicle certified by the type-approval authority in Germany should be: ‘e1 10 15 16’).