This Annex describes the list of parameters to be provided by the vehicle manufacturer as input to the simulation tool. The applicable XML schema as well as example data are available at the dedicated electronic distribution platform.
‘parameter ID’: Unique identifier as used in the simulation tool for a specific input parameter or set of input data.
‘type’: Data type of the parameter
string …sequence of characters in ISO8859-1 encoding
token …sequence of characters in ISO8859-1 encoding, no leading/trailing whitespace
date …date and time in UTC time in the format:YYYY-MM-DDTHH:MM:SSZ with italic letters denoting fixed characters e.g. ‘2002-05-30T09:30:10Z’
integer …value with an integral data type, no leading zeros, e.g. ‘1800’
double, X …fractional number with exactly X digits after the decimal sign (‘.’) and no leading zeros e.g. for ‘double, 2’: ‘2345,67’; for ‘double, 4’: ‘45.6780’.
‘unit’ … physical unit of the parameter.
‘corrected actual mass of the vehicle’ means the mass as specified under the ‘actual mass of the vehicle’ in accordance with Commission Regulation (EU) No 1230/2012 (*) with an exception for the tank(s) which shall be filled to at least 50 % of its or their capacity/ies. The liquid containing systems are filled to 100 % of the capacity specified by the manufacturer, except the liquid containing systems for waste water that must remain empty.
For medium rigid lorries, heavy rigid lorries and tractors the mass is determined without superstructure and corrected by the additional weight of the non-installed standard equipment as specified in point 4.3. The mass of a standard body, standard semi-trailer or standard trailer to simulate the complete vehicle or complete vehicle-(semi-)trailer combination are added automatically by the simulation tool. All parts that are mounted on and above the main frame are regarded as superstructure parts if they are installed only for facilitating a superstructure, independent of the necessary parts for in running order conditions.
For heavy buses that are primary vehicles ‘corrected actual mass of the vehicle’ is not applicable as the generic mass value is allocated by the simulation tool.
‘height of the integrated body’ means the difference in ‘Z’-direction between the reference point ‘A’ of the highest point and lowest point ‘B’ of an integrated body (see Figure 1). For vehicles deviating from the standard case, the following cases are applicable (see Figure 2):
Special case 1, two levels: Height of the integrated body is the average of h1 and h2, where
h1 is the difference between point A, but determined in the cross section of the vehicle at the rear end of first passenger door, and point B
h2 is the difference between point A and point B
Special case 2, inclined: Height of the integrated body is the average of h1 and h2, where
h1 is the difference between point A, but determined in the cross section of the vehicle at the rear end of first passenger door, and point B
h2 is the difference between point A and point B
Special case 3, open top with roof section:
Height of the integrated body determined in the remaining roof section
Special case 4, open top without any roof section:
Height of the integrated body is the difference between the highest point of the vehicle within one meter in the longitudinal direction of the front screen or upper front screen, in the case of a double decker, and point B
For all other cases not covered by standard or special cases 1 to 4, the height of the integrated body is the difference between the highest point of the vehicle and point B. This parameter is relevant only for heavy buses.
reference point ‘A’ means the highest point on the bodywork (Figure 1). Body and/or design panels, brackets for mounting e.g. HVAC systems, hatches and similar items shall not be considered.
reference point ‘B’ means the lowest point on the lower outside edge of the bodywork (Figure 1). Brackets e.g. for axle mounting shall not be considered.
‘vehicle length’ means the vehicle dimension in accordance with Table I of Appendix 1 of Annex I to Regulation (EU) 1230/2012. Additionally, removable load carrier devices, non-removable coupling devices and any other non-removable exterior parts which do not affect the usable space for passengers shall not be taken into account. This parameter is relevant only for heavy buses.
‘vehicle width’ means the vehicle dimension in accordance with Table II of Appendix 1 of Annex I to Regulation (EU) 1230/2012. Deviating from these provisions and not to be considered are removable load carrier devices, non-removable coupling devices and any other non-removable exterior parts which do not affect the usable space for passengers.
‘entrance height in non-kneeled position’ means the floor level within the first door aperture above the ground, measured at the most forward door of the vehicle when the vehicle is in non-kneeled position.
‘fuel cell’ means an energy converter transforming chemical energy (input) into electrical energy (output) or vice versa.
‘fuel cell vehicle’ or ‘FCV’ means a vehicle equipped with a powertrain containing exclusively fuel cell(s) and electric machine(s) as propulsion energy converter(s).
‘fuel cell hybrid vehicle’ or ‘FCHV’ means a fuel cell vehicle equipped with a powertrain containing at least one fuel storage system and at least one rechargeable electric energy storage system as propulsion energy storage systems.
‘pure ICE vehicle’ means a vehicle where all of the propulsion energy converters are internal combustion engines.
‘electric machine’ or ‘EM’ means an energy converter transforming between electrical and mechanical energy.
‘energy storage system’ means a system which stores energy and releases it in the same form as was input.
‘propulsion energy storage system’ means an energy storage system of the powertrain which is not a peripheral device and whose output energy is used directly or indirectly for the purpose of vehicle propulsion.
‘category of propulsion energy storage system’ means a fuel storage system, a rechargeable electric energy storage system (REESS), or a rechargeable mechanical energy storage system.
‘downstream’ means a position in the vehicle’s powertrain that is closer to the wheels than the actual reference position.
‘drivetrain’ means the connected elements of the powertrain for transmission of the mechanical energy between the propulsion energy converter(s) and the wheels.
‘energy converter’ means a system where the form of energy output is different from the form of energy input.
‘propulsion energy converter’ means an energy converter of the powertrain which is not a peripheral device whose output energy is used directly or indirectly for the purpose of vehicle propulsion.
‘category of propulsion energy converter’ means an internal combustion engine, an electric machine, or a fuel cell.
‘form of energy’ means electrical energy, mechanical energy, or chemical energy (including fuels).
‘fuel storage system’ means a propulsion energy storage system that stores chemical energy as liquid or gaseous fuel.
‘hybrid vehicle’ or ‘HV’ means a vehicle equipped with a powertrain containing at least two different categories of propulsion energy converters and at least two different categories of propulsion energy storage systems.
‘hybrid electric vehicle’ or ‘HEV’ means a hybrid vehicle where one of the propulsion energy converters is an electric machine and the other one is an internal combustion engine.
‘serial HEV’ means a HEV with a powertrain architecture where the ICE powers one or more electrical energy conversion paths with no mechanical connection between the ICE and the wheels of the vehicle.
‘internal combustion engine’ or ‘ICE’ means an energy converter with intermittent or continuous oxidation of combustible fuel transforming between chemical and mechanical energy.
‘off-vehicle charging hybrid electric vehicle’ or ‘OVC-HEV’ means a hybrid electric vehicle that can be charged from an external source.
‘parallel HEV’ means a HEV with a powertrain architecture where the ICE powers only a single mechanically connected path between the engine and the wheels of the vehicle.
‘peripheral devices’ means any energy consuming, converting, storing or supplying devices, where the energy is not directly or indirectly used for the purpose of vehicle propulsion but which are essential to the operation of the powertrain.
‘powertrain’ means the total combination in a vehicle of propulsion energy storage system(s), propulsion energy converter(s) and the drivetrain(s) providing the mechanical energy at the wheels for the purpose of vehicle propulsion, plus peripheral devices.
‘pure electric vehicle’ or ‘PEV’ means a motor vehicle pursuant to Regulation (EU) 2018/858, article 3(16), equipped with a powertrain containing exclusively electric machines as propulsion energy converters and exclusively rechargeable electric energy storage systems as propulsion energy storage systems and/or alternatively any other means for direct conductive or inductive supply of electric energy from the power network providing the propulsion energy to the motor vehicle.
‘upstream’ means a position in the vehicle’s powertrain that is further away from the wheels than the actual reference position.
‘IEPC’ means an integrated electric powertrain component in accordance with point 2(36) of Annex Xb.
‘IHPC Type 1’ means an integrated hybrid electric vehicle powertrain component Type 1 in accordance with point 2(38) of Annex Xb;
‘dynamic charging technology’ means a technology that enables the vehicle to be connected to an external electrical power supply while in motion, providing direct power to the vehicle’s propulsion and/or auxiliary systems and/or charging the batteries;
‘overhead pantograph’ means dynamic charging technology for connection and power supply with overhead contact line infrastructure on roads;
‘overhead trolley’ means dynamic charging technology with current collector poles for connection with overhead contact line infrastructure;
‘ground rail’ means dynamic charging technology that conductively transfers the electrical energy to the vehicle through rails embedded in or on top of the road surface;
‘wireless’ means dynamic charging technology that inductively transfers the electrical energy to the vehicle through devices embedded in or on top of the road surface providing magnetic fields;
‘compressed gaseous hydrogen’ means a hydrogen storage technology which stores hydrogen in gaseous form;
‘liquid hydrogen’ means a hydrogen storage technology which stores hydrogen in liquid form;
‘cryo-compressed hydrogen’ means a hydrogen storage technology which stores hydrogen at temperatures from close to liquefication up to ambient temperature and at a pressure of at least 200 bar. The hydrogen storage technology may be capable of operating at ambient temperature but its nominal capacity may only be reached close to the liquefaction temperature of hydrogen;
‘empty hydrogen tank condition’ means the condition of a hydrogen tank from which it is still possible to reach a full tank in a single refuelling event without venting and which meets any of the following conditions:
below which an indication to the driver ‘empty’ or ‘almost empty’ or similar appears;
below which a significantly limited performance is provided by the hydrogen energy conversion system;
‘off-vehicle charging hybrid vehicle’ or ‘OVC-HV’ means a hybrid vehicle that can be charged from an external source;
‘off-vehicle charging fuel cell hybrid vehicle’ or ‘OVC-FCHV’ means a fuel cell hybrid vehicle that can be charged from an external source;
‘driver-selectable mode’ means a distinct driver-selectable condition which could affect emissions, or fuel and/or energy consumption;
‘predominant mode’ means a single driver-selectable mode that is always selected when the vehicle is switched on, regardless of the driver-selectable mode in operation when the vehicle was previously shut down, which meets the following conditions:
it cannot be redefined to another mode;
it can only be switched to another driver-selectable mode by an intentional action of the driver after the vehicle is switched on;
‘battery-only predominant mode’ means a predominant mode where an OVC-HV is operating with the propulsion energy being provided exclusively by the REESS.
In Tables 1 to 17 the sets of input parameters to be provided regarding the characteristics of the vehicle are specified. Different sets are defined depending on the application case (medium lorries, heavy lorries and heavy buses).
For heavy buses a differentiation is made between input parameters to be provided for the simulations at the primary vehicle and for the simulations at the complete vehicle or completed vehicle. The following provisions shall apply:
Primary vehicle manufacturers shall provide all parameters listed in the primary vehicle column.
Primary vehicle manufacturers may furthermore provide additional input parameters related to the complete or completed vehicle, which can be determined already at this initial stage. In this case information on Manufacturer (P235), Manufacturer Address (P252), VIN (P238) and Date (P239) shall be provided both for the set of primary input parameters and for the set of additional input parameters.
Interim manufacturers shall provide input parameters related to the complete or completed vehicle which can be determined at this stage and which are under their responsibility. If a parameter which was already provided by a previous manufacturing stage is updated, the entire status of the parameter must be specified (example: if a second heat pump is added to the vehicle, the technology of both systems shall be provided). Information on Manufacturer (P235), Manufacturer Address (P252), VIN (P238) and Date (P239) and shall be provided by interim manufacturers in all cases;
Manufactures of the completed vehicle shall provide input parameters which can be determined at this stage and which are under their responsibility. For necessary updates of parameters already provided by previous manufacturing stages, the same provisions as for interim manufacturers shall apply. Information on Manufacturer (P235), Manufacturer Address (P252), VIN (P238), Date (P239) and Corrected Actual Mass (P038) shall be provided in all cases. In order to be able to carry out the necessary simulations, the consolidated data set from all manufacturing stages must contain the entire information listed in the column for the complete vehicle or completed vehicle;
Manufacturers related to the complete stage shall provide all input parameters. Information on Manufacturer (P235), Manufacturer Address (P252), VIN (P238) and Date (P239) shall be provided both for the primary input parameters and for the complete vehicle input parameters;
The parameter ‘VehicleDeclarationType’ (P293) shall be delivered by all manufacturing stages which provide any of the parameters as listed for the complete or completed vehicle.
[In the event multiple PTOs are mounted to the transmission, only the component with the highest losses according to point 3.6 of Annex IX, for its combination of criteria ‘PTOShaftsGearWheels’ and ‘PTOShaftsOtherElements’, shall be declared.]
Parameter name | Parameter ID | Type | Unit | Description/Reference | Heavy lorries | Medium lorries | Heavy buses (primary vehicle) | Heavy buses (complete or completed vehicle)
Manufacturer | P235 | Token | [-] | | X | X | X | X
Manufacturer Address | P252 | Token | [-] | | X | X | X | X
Model_CommercialName | P236 | Token | [-] | | X | X | X | X
VIN | P238 | Token | [-] | | X | X | X | X
Date | P239 | Date Time | [-] | Date and time when input information and input data is created | X | X | X | X
Legislative Category | P251 | String | [-] | Allowed values: ‘N2’, ‘N3’,‘M3’ | X | X | X | X
ChassisConfiguration | P036 | String | [-] | Allowed values: ‘Rigid Lorry’, ‘Tractor’, ‘Van’, ‘Bus’ | X | X | X |
AxleConfiguration | P037 | String | [-] | Allowed values: ‘4 × 2’, ‘4 × 2F’, ‘6 × 2’, ‘6 × 4’, ‘8 × 2’, ‘8 × 4’where ‘4 × 2F’ refers to 4 × 2 vehicles with a driven front axle | X | X | X |
Articulated | P281 | boolean | | In accordance with Article 3, point (37) | | | X |
CorrectedActualMass | P038 | Int | [kg] | In accordance with ‘Corrected actual mass of the vehicle’ as specified in point 2(4) | X | X | | X
TechnicalPermissibleMaximumLadenMass | P041 | int | [kg] | In accordance with Article 2, point (7) of Regulation (EU) No 1230/2012 | X | X | X | X
IdlingSpeed | P198 | int | [1/min] |
In accordance with point 7.1
For PEV and FCHV no input is required
X | X | X |
RetarderType | P052 | string | [-] |
Allowed values: ‘None’, ‘Losses included in Gearbox’, ‘Engine Retarder’, ‘Transmission Input Retarder’, ‘Transmission Output Retarder’, ‘Axlegear Input Retarder’
‘Axlegear Input Retarder’ is applicable only for powertrain architectures ‘E3’, ‘S3’, ‘F3, ‘S-IEPC’, ‘F-IEPC’ and ‘E-IEPC’.
Separate entry for each individual powertrain in the case of multiple mechanically independent powertrains in accordance with point 10.1.4.
X | X | X |
RetarderRatio | P053 | double, 3 | [-] |
Step-up ratio in accordance with table 2 of Annex VI
Separate entry for each individual powertrain in the case of multiple mechanically independent powertrains in accordance with point 10.1.4.
X | X | X |
AngledriveType | P180 | string | [-] |
Allowed values: ‘None’, ‘Losses included in Gearbox’, ‘Separate Angledrive’
Separate entry for each individual powertrain in the case of multiple mechanically independent powertrains in accordance with point 10.1.4.
X | X | X |
PTOShafts GearWheels | P247 | string | [-] |
Allowed values: ‘none’, ‘only the drive shaft of the PTO’, ‘drive shaft and/or up to 2 gear wheels’, ‘drive shaft and/or more than 2 gear wheels’, ‘only one engaged gearwheel above oil level’ , ‘PTO which includes 1 or more additional gearmesh(es), without disconnect clutch’
Separate entry for each individual powertrain in the case of multiple mechanically independent powertrains in accordance with point 10.1.4.
In case of IEPS and IHPC, no input shall be made.
X | | |
PTOOther Elements | P248 | string | [-] |
Allowed values: ‘none’, ‘shift claw, synchroniser, sliding gearwheel’, ‘multi-disc clutch’, ‘multi-disc clutch, oil pump’
Separate entry for each individual powertrain in the case of multiple mechanically independent powertrains in accordance with point 10.1.4.
X | | |
Engine input data in accordance with Appendix 7 of Annex V | Only applicable if the component is present in the vehicle | X | X | X |
Transmission input data in accordance with Table 1 to Table 3 in Appendix 12 of Annex VI | Only applicable if the component is present in the vehicle. Separate entry for each individual powertrain in the case of multiple mechanically independent powertrains in accordance with point 10.1.4 | X | X | X |
Torque converter input data in accordance with Table 4 and Table 5 in Appendix 12 of Annex VI | Only applicable if the component is present in the vehicle. Separate entry for each individual powertrain in the case of multiple mechanically independent powertrains in accordance with point 10.1.4 | X | X | X |
Axle input data in accordance with Table 1 and Table 2 in Appendix 6 of Annex VII | Only applicable if the component is present in the vehicle. Separate entry for each individual powertrain in the case of multiple mechanically independent powertrains in accordance with point 10.1.4 | X | X | X |
Angle drive input data in accordance with Table 6 and Table 7 in Appendix 12 of Annex VI |
Refers to certified ADC component installed in the angle drive position.
Only applicable if the component is present in the vehicle.
Separate entry for each individual powertrain in the case of multiple mechanically independent powertrains in accordance with point 10.1.4.
X | X | X |
Retarder input data in accordance with Table 8 and Table 9 in Appendix 12 of Annex VI |
Only applicable if the component is present in the vehicle and the retarder losses are not provided together with the input data for the transmission component.
Separate entry for each individual powertrain in the case of multiple mechanically independent powertrains in accordance with point 10.1.4.
X | X | X |
Air drag input data in accordance with Table 1 in Appendix 9 of Annex VIII | P268 | token | [-] | Only applicable if certified input data is provided | X | X | | X
AirdragModifiedMultistage | P334 | boolean | [-] |
Input required for all manufacturing stages subsequent to a first entry to the air drag component.
If parameter is set to ‘true’ w/o providing a certified air drag component, the simulation tool applies standard values according to Annex VIII.
X
IEPC input data in accordance with Appendix 15 of Annex Xb |
Only applicable if the component is present in the vehicle.
Separate entry for each individual powertrain in the case of multiple mechanically independent powertrains in accordance with point 10.1.4
X | X | X |
ZeroEmissionVehicle | P269 | boolean | [-] | As defined in Article 3, point (15) | X | X | X |
VocationalVehicle | P270 | boolean | [-] | In accordance with Article 3, point (9) of Regulation (EU) 2019/1242 | X | | |
NgTankSystem | P275 | string | [-] |
Allowed values: ‘Compressed’, ‘Liquefied’
Only relevant for vehicles with engines of fuel type ‘NG PI’ and ‘NG CI’ (P193)
Where both tank systems are present on a vehicle, the system which is able to contain the higher amount of fuel energy shall be declared as input to the simulation tool.
X | X | | X
Sleepercab | P276 | boolean | [-] | | X | | |
ClassBus | P282 | string | [-] | Allowed values: ‘I’, ‘I+II’, ‘A’, ‘II’, ‘II+III’, ‘III’, ‘B’ in accordance with paragraph 2 of UN Regulation No. 107 | | | | X
NumberPassengersSeatsLowerDeck | P283 | int | [-] |
Number of passenger seats - excluding driver and crew seats.