ANNEX X, Regulation (EU) 2017/2400

In forcesince 1 Jul 2022cited 2×

This Annex describes the certification provisions for tyre with regard to its rolling resistance coefficient. For the calculation of the vehicle rolling resistance to be used as the simulation tool input, the applicable tyre rolling resistance coefficient Cr for each tyre supplied to the original equipment manufacturers and the related tyre test load FZTYRE shall be declared by the applicant for pneumatic tyre approval.

For the purposes of this Annex, in addition to the definitions contained in UN Regulation No. 54 [Regulation No 54 of the Economic Commission for Europe of the United Nations (UNECE) — Uniform provisions concerning the approval of pneumatic tyres for commercial vehicles and their trailers (OJ L 183, 11.7.2008, p. 41).] and in UN Regulation No. 117 [Regulation No 117 of the Economic Commission for Europe of the United Nations (UNECE) — Uniform provisions concerning the approval of tyres with regard to rolling sound emissions and/or to adhesion on wet surfaces and/or to rolling resistance [2016/1350] (OJ L 218, 12.8.2016, p. 1).], the following definitions shall apply:

(1)

‘Rolling resistance coefficient Cr’ means a ratio of the rolling resistance to the load on the tyre

(2)

‘The load on the tyre FZTYRE’ means a load applied to the tyre during the rolling resistance test.

(3)

‘Type of tyre’ means a range of tyres which do not differ in such characteristics as:

(a)

Manufacturer's name;

(b)

Brand name or trade mark ;

(c)

Tyre class (in accordance with UN Regulation No. 117);

(d)

Tyre-size designation;

(e)

Tyre structure (diagonal (bias-ply), radial);

(f)

Category of use (normal tyre, snow tyre, special use tyre) as defined in UN Regulation No.117;

(g)

Speed category (categories);

(h)

Load-capacity index (indices);

(i)

Trade description/commercial name;

(j)

Declared tyre rolling resistance coefficient

(4)

‘FuelEfficiencyClass’ is a parameter corresponding to the fuel efficiency class of the tyre as defined in Regulation (EU) 2020/740 [Regulation (EU) 2020/740 of the European Parliament and of the Council of 25 May 2020 on the labelling of tyres with respect to fuel efficiency and other parameters, amending Regulation (EU) 2017/1369 and repealing Regulation (EC) No 1222/2009 (OJ L 177, 5.6.2020, p. 1).] Annex I, part A. For tyres which are not in the scope of Regulation (EU) 2020/740, the fuel efficiency class of the tyre is not applicable and parameter FuelEfficiencyClass shall be recorded in Appendix 3 as ‘N/A’.

3.1.

The tyre manufacturer plant shall be certified to IATF 16949.

The tyre rolling resistance coefficient shall be measured and aligned in accordance with Regulation (EU) 2020/740 Annex I, part A, expressed in N/kN and rounded to the first decimal place, in accordance with ISO 80000-1 Appendix B, section B.3, rule B (example 1).

The standard rolling resistance coefficient value for C2 and C3 tyres shall be the one corresponding to snow tyres for use in severe snow conditions as set out in UN Regulation No. 117 paragraph 6.3.2. For tyres not in the scope of Regulation (EC) No 661/2009 [Regulation (EC) No 661/2009 of the European Parliament and of the Council of 13 July 2009 concerning type-approval requirements for the general safety of motor vehicles, their trailers and systems, components and separate technical units intended therefor (OJ L 200, 31.7.2009, p. 1).] or Regulation (EU) 2019/2144 [Regulation (EU) 2019/2144 of the European Parliament and of the Council of 27 November 2019 on type-approval requirements for motor vehicles and their trailers, and systems, components and separate technical units intended for such vehicles, as regards their general safety and the protection of vehicle occupants and vulnerable road users, amending Regulation (EU) 2018/858 of the European Parliament and of the Council (OJ L 325, 16.12.2019, p. 1)], the standard value shall be 13,0 N/kN and the FuelEfficiencyClass shall be stated as ‘N/A’.

The standard FzISO value shall be the one obtained as a percentage of the vertical force related to tyre load index at nominal tyre pressure (and single tyre application). For C2 and C3 tyres this percentage shall be 85 %, for other tyres the percentage shall be 80 %.

The tyre manufacturer shall test either in a laboratory of technical services as defined in Article 68 of Regulation (EU) 2018/858 the test referred to in point 3.2, or in its own facilities in the case that:

(i)

a representative of a technical service designated by the responsible approval authority supervises the test; or

(ii)

the tyre manufacturer is designated as a technical service of Category A in accordance with Article 68 of Regulation (EU) 2018/858.

3.4.1.

The tyre shall be clearly identifiable in respect to the applicable certificate and the corresponding rolling resistance coefficient.

3.4.2.

The tyre manufacturer shall use the markings affixed to the side wall of the tyre or affix an additional identifier to the tyre. The additional identification shall ensure a unique link of the tyre and its rolling resistance coefficient. It may take a form of:

quick response (QR) code,

barcode,

radio-frequency identification (RFID),

an additional marking, or

other tool fulfilling the requirements of 3.4.1.

3.4.3.

If an additional identifier is used it shall remain readable until the moment of sales of the vehicle.

3.4.4.

In line with Article 38(2) of Regulation (EU) 2018/858, no type-approval mark is required for tyres certified in accordance with this Regulation.

4.1.

Any tyre certified under this Regulation shall be in conformity to the declared rolling resistance value as per paragraph 3.2 of this Annex.

4.2.

In order to verify conformity of the certified CO2 emissions and fuel consumption related properties, production samples shall be taken randomly from series production and tested in accordance with the provisions set out in paragraph 3.2. The tests have to be performed on new test tyres in the sense of the definition set out in paragraph 2 of UN Regulation No. 117.

4.3.1

The tyre rolling resistance of at least one tyre of a specific type intended for the sales to the original equipment manufacturers shall be tested every 20000 units of this type per year (e.g. 2 conformity verifications per year of the type whose annual sales volume to the original equipment manufacturers is between 20001 and 40000 units).

4.3.2

In case the deliveries of a specific tyre type intended for the sales to the original equipment manufacturers is between 500 and 20000 units per year, at least one conformity verification of the type shall be carried out per year.

4.3.3

In case the deliveries of a specific tyre type intended for the sales to the original equipment manufacturers is below 500 units, at least one conformity verification as described in paragraph 4.4 shall be applied every second year.

4.3.4

If the volume of tyres delivered to the original equipment manufacturers indicated in 4.3.1 is met within 31 calendar days the maximum number of conformity verifications as described in paragraph 4.3 is limited to one per 31 calendar days.

4.3.5

The manufacturer shall justify (ex. by showing sales numbers) to the approval authority the number of tests which has been performed

4.4.1

A single tyre shall be tested in accordance with paragraph 3.2. By default, the machine alignment equation shall be the one valid at the date of verification testing. Tyre manufacturer may request the application of the alignment equation that was used during the certification testing and reported in the information document.

4.4.2

In the case that the measured and aligned value is lower or equal to the declared value plus 0,3 N/kN, the tyre rolling resistance value is considered compliant.

4.4.3

Where the measured and aligned value exceeds the declared value by more than 0,3 N/kN, the alignment equation that was valid at the time of the certification testing may be applied upon request of the tyre manufacturer and in agreement with the authority that is supervising the verification.

4.4.3.1

If the measured and realigned value is lower or equal to the declared value plus 0,3 N/kN, the tyre rolling resistance value is considered compliant.

4.4.3.2

If the measured value, aligned as per points 4.4.3 and 4.4.3.1, exceeds the declared value by more than 0,3 N/kN, three additional tyres shall be tested. If the measured value, aligned as per points 4.4.3 and 4.4.3.1, of at least one of the three tyres exceeds the declared value by more than 0,4 N/kN, Article 23 shall apply.

[‘delete as appropriate’]

Communication concerning:

granting

extension

refusal

withdrawal

Administration stamp

of a certificate on CO2 emission and fuel consumption related properties of a tyre family in accordance with Commission Regulation (EU) 2017/2400, as amended by Commission Regulation (EU) 2019/318

Certification number: …

Hash: …

Reason for extension: …

1.

Manufacturer's name and address: …

2.

If applicable, name and address of manufacturer's representative: …

3.

Brand name/trade mark: …

4.

Tyre type description: …

(a)

Manufacturer's name …

(b)

Brand name or trade mark

(c)

Tyre class (in accordance with Regulation (EC) No 661/2009 or Regulation (EU) 2019/2144)

(d)

Tyre-size designation …

(e)

Tyre structure (diagonal (bias-ply); radial) …

(f)

Category of use (normal tyre, snow tyre, special use tyre) …

(g)

Speed category (categories) …

(h)

Load-capacity index (indices) …

(i)

Trade description/commercial name …

(j)

Declared tyre rolling resistance coefficient …

5.

Tyre identification code(s) and technology(ies) used to provide identification code(s), if applicable:

Technology: | Code:

… | …

6.

Technical Service and, where appropriate, test laboratory approved for purposes of approval or of verification of conformity tests: …

7.

Declared values:

7.1. declared rolling resistance level of the tyre (in N/kN rounded to the first decimal place, in accordance with ISO 80000-1 Appendix B, section B.3, rule B (example 1))

Cr, … [N/kN]

7.2. tyre test load in accordance with Regulation (EU) 2020/740, Annex I, part A

FZTYRE…[N]

7.3. Alignment equation: …

8.

Any remarks: …

9.

Place: …

10.

Date: …

11.

Signature: …

12.

Annexed to this communication are: …

0.1

Name and address of manufacturer;

0.2

Brand name(s)/trademark(s);

0.3

Name and address of applicant:

0.4

Trade description(s)/commercial name(s);

0.5

Tyre class (in accordance with UN Regulation No. 117);

0.6

Tyre-size designation;

0.7

Tyre structure (diagonal (bias-ply); radial);

0.8

Category of use (normal tyre, snow tyre, special use tyre);

0.9

Speed category (categories);

0.10

Load-capacity index (indices);

0.11

-

0.12

Declared rolling resistance coefficient;

0.13

Tool(s) to provide additional rolling resistance coefficient identification code (if any);

0.14.

Rolling resistance level of the tyre (in N/kN rounded to the first decimal place, according to ISO80000-1 Appendix B, section B.3, rule B (example 1)) Cr, … [N/kN]

0.15

Load FZTYRE: … [N]

0.16

Alignment equation: ….

0.16

Tyre Type Approval Marking (in accordance with UN Regulation No. 117), if applicable;

0.17

Tyre Type Approval Marking (in accordance with UN Regulation No. 54 or 30 [Regulation No 30 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of pneumatic tyres for motor vehicles and their trailers (OJ L 201, 30.7.2008, p. 70).]

1.

Approval Authority or Technical Service [or Accredited Lab]:

2.

Test report No.:

3.

Comments (if any):

4.

Date of test report:

5.

Test machine identification and drum diameter/surface:

6.

Test tyre details:

6.1. Tyre size designation and service description:

6.2. Tyre brand/ trade description:

6.3. Reference test inflation pressure: kPa

7.

Test data:

7.1. Measurement method:

7.2. Test speed: km/h

7.3. Load FZTYRE: N

7.4. Test inflation pressure, initial: kPa

7.5. Distance from the tyre axis to the drum outer surface under steady state conditions, rL: m

7.6. Test rim width and material:

7.7. Ambient temperature: °C

7.8. Skim test load (except deceleration method): N

8.

Rolling resistance coefficient:

8.1. Initial value (or average in the case there is more than one): N/kN

8.2. Temperature corrected: … N/kN

8.3. Temperature and drum diameter corrected: N/kN

8.4. Alignment equation:

8.5. Rolling resistance level of the tyre (in N/kN rounded to the first decimal place, in accordance with ISO80000-1 Appendix B, section B.3, rule B (example 1)) Cr,aligned: … [N/kN]

9.

Date of test:

This Appendix describes the list of parameters to be provided by the component manufacturer as input to the simulation tool. The applicable XML schema as well as example data are available at the dedicated electronic distribution platform.

(1)‘Parameter ID’:Unique identifier as used in the simulation tool for a specific input parameter or set of input data

(2)‘Type’:

Data type of the parameter

string …sequence of characters in ISO8859-1 encoding

token …sequence of characters in ISO8859-1 encoding, no leading/trailing whitespace

date …date and time in UTC time in the format: YYYY-MM-DDTHH:MM:SSZ with italic letters denoting fixed characters e.g. ‘2002-05-30T09:30:10Z’

integer …value with an integral data type, no leading zeros, e.g. ‘1800’

double, X …fractional number with exactly X digits after the decimal sign (‘.’) and no leading zeros e.g. for ‘double, 2’: ‘2345.67’; for ‘double, 4’: ‘45.6780’

(3)‘Unit’ …physical unit of the parameter

Parameter name | Param ID | Type | Unit | Description/Reference

Manufacturer | P230 | token | |

Model | P231 | token | | Trade name of manufacturer

CertificationNumber | P232 | token | |

Date | P233 | date | | Date and time when the component hash is created.

AppVersion | P234 | token | | Version number identifying the evaluation tool

RRCDeclared | P046 | double, 4 | [N/N] |

FzISO | P047 | integer | [N] |

Tyre Size Designation | P108 | string | [-] | Allowed values (non-exhaustive): ‘9.00 R20’, ‘9 R22.5’, ‘9.5 R17.5’, ‘10 R17.5’, ‘10 R22.5’, ‘10.00 R20’, ‘11 R22.5’, ‘11.00 R20’, ‘11.00 R22.5’, ‘12 R22.5’, ‘12.00 R20’, ‘12.00 R24’, ‘12.5 R20’, ‘13 R22.5’, ‘14.00 R20’, ‘14.5 R20’, ‘16.00 R20’, ‘205/75 R17.5’, ‘215/75 R17.5’, ‘225/70 R17.5’, ‘225/75 R17.5’, ‘235/75 R17.5’, ‘245/70 R17.5’, ‘245/70 R19.5’, ‘255/70 R22.5’, ‘265/70 R17.5’, ‘265/70 R19.5’, ‘275/70 R22.5’, ‘275/80 R22.5’, ‘285/60 R22.5’, ‘285/70 R19.5’, ‘295/55 R22.5’, ‘295/60 R22.5’, ‘295/80 R22.5’, ‘305/60 R22.5’, ‘305/70 R19.5’, ‘305/70 R22.5’, ‘305/75 R24.5’, ‘315/45 R22.5’, ‘315/60 R22.5’, ‘315/70 R22.5’, ‘315/80 R22.5’, ‘325/95 R24’, ‘335/80 R20’, ‘355/50 R22.5’, ‘365/70 R22.5’, ‘365/80 R20’, ‘365/85 R20’, ‘375/45 R22.5’, ‘375/50 R22.5’, ‘375/90 R22.5’, ‘385/55 R22.5’, ‘385/65 R22.5’, ‘395/85 R20’, ‘425/65 R22.5’, ‘495/45 R22.5’, ‘525/65 R20.5’

TyreClass | P370 | string | [-] | ‘C2’, ‘C3’ or ‘N/A’

FuelEfficiencyClass | P371 | string | | ‘A’, ‘B’, ‘C’, ‘D’, ‘E’ or ‘N/A’

1.1

Certification number for tyres shall comprise the following:

section 1 | section 2 | section 3 | Additional letter to section 3 | section 4 | section 5

Indication of country issuing the certificate | HDV CO2 determination Regulation ‘2017/2400’ | Latest amending Regulation (ZZZZ/ZZZZ) | T = Tyre | Base certification number 00000 | Extension 00