This annex describes the certification provisions regarding the torque losses of transmissions, torque converter (TC), other torque transferring components (OTTC) and additional driveline components (ADC) for heavy duty vehicles. In addition it defines calculation procedures for the standard torque losses.
Torque converter (TC), other torque transferring components (OTTC) and additional driveline components (ADC) can be tested in combination with a transmission or as a separate unit. In the case that those components are tested separately the provisions of section 4, 5 and 6 apply. Torque losses resulting from the drive mechanism between the transmission and those components can be neglected.
For the purposes of this Annex the following definitions shall apply:
‘Transfer case’ means a device that splits the engine power of a vehicle and directs it to the front and rear drive axles. It is mounted behind the transmission and both front and rear drive shafts connect to it. It comprises either a gearwheel set or a chain drive system in which the power is distributed from the transmission to the axles. The transfer case will typically have the ability to shift between standard drive mode (front or rear wheel drive), high range traction mode (front and rear wheel drive), low range traction mode and neutral;
‘Gear ratio’ means the forward gear ratio of the speed of the input shaft (towards prime mover) to the speed of the output shaft (towards driven wheels) without slip (i = nin/nout);
‘Ratio coverage’ means the ratio of the largest to the smallest forward gear ratios in a transmission: φtot = imax/imin;
‘Compound transmission’ means a transmission, with a large number of forward gears and/or large ratio coverage, composed of sub-transmissions, which are combined to use most power-transferring parts in several forward gears;
‘Main section’ means the sub-transmission that has the largest number of forward gears in a compound transmission;
‘Range section’ means a sub-transmission normally in series connection with the main section in a compound transmission. A range section usually has two shiftable forward gears. The lower forward gears of the complete transmission are embodied using the low range gear. The higher gears are embodied using the high range gear;
‘Splitter’ means a design that splits the main section gears in two (usually) variants, low- and high split gears, whose gear ratios are close compared to the ratio coverage of the transmission. A splitter can be a separate sub-transmission, an add-on device, integrated with the main section or a combination thereof;
‘Tooth clutch’ means a clutch where torque is transferred mainly by normal forces between mating teeth. A tooth clutch can either be engaged or disengaged. It is operated in load-free conditions, only (e.g., at gear shifts in a manual transmission);
‘Angle drive’ means a device that transmits rotational power between non-parallel shafts, often used with transversely oriented engine and longitudinal input to driven axle;
‘Friction clutch’ means clutch for transfer of propulsive torque, where torque is sustainably transferred by friction forces. A friction clutch can transmit torque while slipping, it can thereby (but does not have to) be operated at start-offs and at powershifts (retained power transfer during a gear shift);
‘Synchroniser’ means a type of tooth clutch where a friction device is used to equalise the speeds of the rotating parts to be engaged;
‘Gear mesh efficiency’ means the ratio of output power to input power when transmitted in a forward gear mesh with relative motion;
‘Crawler gear’ means a low forward gear (with speed reduction ratio that is larger than for the non-crawler gears) that is designed to be used infrequently, e.g., at low-speed manoeuvres or occasional up-hill start-offs;
‘Power take-off (PTO)’ means a device on a transmission or an engine to which an auxiliary driven device, e.g., a hydraulic pump, can be connected;
‘Power take-off drive mechanism’ means a device in a transmission that allows the installation of a power take-off (PTO);
‘Lock-up clutch’ means a friction clutch in a hydrodynamic torque converter; it can connect the input and output sides, thereby eliminating the slip. In some cases permanent slip in fixed gears is intended, e.g. to prevent vibrations;
‘Start-off clutch’ means a clutch that adapts speed between engine and driving wheels when the vehicle starts off. The start-off clutch is usually located between engine and transmission;
‘Synchronised Manual Transmission (SMT)’ means a manually operated transmission with two or more selectable speed ratios that are obtained using synchronisers. Ratio changing is normally achieved during a temporary disconnection of the transmission from the engine using a clutch (usually the vehicle start-off clutch);
‘Automated Manual Transmission or Automatic Mechanically-engaged Transmission (AMT)’ means an automatically shifting transmission with two or more selectable speed ratios that are obtained using tooth clutches (un-/synchronised). Ratio changing is achieved during a temporary disconnection of the transmission from the engine. The ratio shifts are performed by an electronically controlled system managing the timing of the shift, the operation of the clutch between engine and gearbox and the speed and torque of the engine. The system selects and engages the most suitable forward gear automatically, but can be overridden by the driver using a manual mode;
‘Dual Clutch Transmission (DCT)’ means an automatically shifting transmission with two friction clutches and several selectable speed ratios that are obtained by the use of tooth clutches. The ratio shifts are performed by an electronically controlled system managing the timing of the shift, the operation of the clutches and the speed and torque of the engine. The system selects the most suitable gear automatically, but can be overridden by the driver using a manual mode. In some cases permanent slip in fixed gears is intended, e.g. to prevent vibrations;
‘Retarder’ means an auxiliary braking device in a vehicle powertrain; aimed for permanent braking;
‘Case S’ means an Automatic Powershifting Transmission (APT) with serial arrangement of a torque converter and the connected mechanical parts of the transmission;
‘Case P’ means an APT with parallel arrangement of a torque converter and the connected mechanical parts of the transmission (e.g. in power split installations);
‘Automatic Powershifting Transmission (APT)’ means an automatically shifting transmission with more than two friction clutches and several selectable speed ratios that are obtained mainly by the use of those friction clutches. The ratio shifts are performed by an electronically controlled system managing the timing of the shift, the operation of the clutches and the speed and torque of the engine. The system selects the most suitable gear automatically, but can be overridden by the driver using a manual mode. Shifts are normally performed without traction interruption (friction clutch to friction clutch);
‘Oil conditioning system’ means an external system that conditions the oil of a transmission at testing. The system circulates oil to and from the transmission. The oil is thereby filtered and/or temperature conditioned;
‘Smart lubrication system’ means a system that will affect the load independent losses (also called spin losses or drag losses) of the transmission depending on the input torque and/or power flow through the transmission. Examples are controlled hydraulic pressure pumps for brakes and clutches in an APT, controlled variable oil level in the transmission, controlled variable oil flow/pressure for lubrication and cooling in the transmission. Smart lubrication can also include control of the oil temperature of the transmission, but smart lubrication systems that are designed only for controlling the temperature are not considered here, since the transmission testing procedure has fixed testing temperatures;
‘Transmission electric auxiliary’ means an electric auxiliary used for the function of the transmission during running steady state operation. A typical example is an electric cooling/lubrication pump (but not electric gear shift actuators and electronic control systems including electric solenoid valves, since they are low energy consumers, especially at steady state operation);
‘Oil type viscosity grade’ means a viscosity grade as defined by SAE J306;
‘Factory fill oil’ means the oil type viscosity grade that is used for the oil fill in the factory and which is intended to stay in the transmission, torque converter, other torque transferring component or in an additional driveline component for the first service interval;
‘Gearscheme’ means the arrangement of shafts, gearwheels and clutches in a transmission;
‘Powerflow’ means the transfer path of power from input to output in a transmission via shafts, gearwheels and clutches;
‘Differential’ means a device that splits a torque into two branches, e.g. for left- and right-hand side wheels, while allowing these branches to rotate at unequal speeds. The torque-splitting function can be biased or deactivated by a differential brake- or differential lock device (if applicable);
‘Case N’ means an APT without a torque converter.
For testing the losses of a transmission the torque loss map for each individual transmission type shall be measured. Transmissions may be grouped into families with similar or equal CO2-relevant data following the provisions of Appendix 6 to this Annex.
For the determination of the transmission torque losses, the applicant for a certificate shall apply one of the following methods for each single forward gear (crawler gears excluded).
Option 1: Measurement of the torque independent losses, calculation of the torque dependent losses.
Option 2: Measurement of the torque independent losses, measurement of the torque loss at maximum torque and interpolation of the torque dependent losses based on a linear model
Option 3: Measurement of the total torque loss.
3.1
Option 1: Measurement of the torque independent losses, calculation of the torque dependent losses.
The torque loss Tl,in on the input shaft of the transmission shall be calculated by
Tl,in(nin,Tin,gear) = Tl,in,min_loss + fT × Tin + floss_corr × Tin + Tl,in,min_el + fel_corr × Tin + flosstcc × Tin
The correction factor for the torque dependent hydraulic torque losses shall be calculated by
floss_corr
Tl,in,max_lossTl,in,min_loss
Tmax,in
The correction factor for the torque dependent electric torque losses shall be calculated by
fel_corr
Tl,in,max_elTl,in,min_el
Tmax,in
The torque loss at the input shaft of the transmission caused by the power consumption of transmission electric auxiliary shall be calculated by
Tl,in,el
Pel
0,7nin2π60
The correction factor for the losses in a slipping TC lock-up clutch as defined in point 2(16) or slipping input side clutch as defined in point 2(20) shall be calculated by:
flosstcc
Δntcc
nin
where:
Tl,inTorque loss related to input shaft [Nm]
Tl,in,min_lossTorque independent loss at minimum hydraulic loss level (minimum main pressure, cooling/lubrication flows etc.), measured with free rotating output shaft from testing without load [Nm]
Tl,in,max_lossTorque independent loss at maximum hydraulic loss level (maximum main pressure, cooling/lubrication flows etc.), measured with free rotating output shaft from testing without load [Nm]
floss_corrLoss correction for hydraulic loss level depending on input torque [-]
ninSpeed at the transmission input shaft (downstream of torque converter, if applicable) [rpm]
fTTorque loss coefficient = 1 – ηT
TinTorque at the input shaft [Nm]
ηTTorque dependent efficiency (to be calculated); for a direct gear fT = 0,007 (ηT = 0,993) [-]
fel_corrLoss correction for electric power loss level depending on input torque [-]
Tl,in, elAdditional torque loss on input shaft by electric consumers [Nm]
Tl,in,min_elAdditional torque loss on input shaft by electric consumers corresponding to minimum electric power [Nm]
Tl,in,max_elAdditional torque loss on input shaft by electric consumers corresponding to maximum electric power [Nm]
PelElectric power consumption of electric consumers in transmission measured during transmission loss testing [W]
Tmax,inMaximum allowed input torque for any forward gear in the transmission [Nm]
floss_tccLoss correction factor for slipping torque converter (or input side) clutch
ntccDifference in speed between upstream and downstream side of slipping TC lock-up clutch as defined in point 2(16) or slipping input side clutch as defined in 2(20) [rpm] (speed downstream of the slipping clutch is the speed nin at the transmission input shaft)
3.1.1.
The torque dependent losses of a transmission system shall be determined as described in the following:
In case of multiple parallel and nominally equal power flows, e.g., twin countershafts or several planet gearwheels in a planetary gear set, that can be treated as one power flow in this section.
3.1.1.1.
For each indirect gear g of common transmissions with a non-split power flow and ordinary, non-planetary gear sets, the following steps shall be performed:
3.1.1.2.
For each active gear mesh, the torque dependent efficiency shall be set to constant values of ηm:
external – external gear meshesηm = 0,986
external – internal gear meshesηm = 0,993
angle drive gear meshesηm = 0,97
(Angle drive losses may alternatively be determined by separate testing as described in paragraph 6. of this Annex)
3.1.1.3.
The product of these torque dependent efficiencies in active gear meshes shall be multiplied with a torque dependent bearing efficiency ηb = 99,5 %.
3.1.1.4.
The total torque dependent efficiency ηTg for the gear g shall be calculated by:
ηTg = ηb * ηm,1 * ηm,2 * […] * ηm,n
3.1.1.5.
The torque dependent loss coefficient fTg for the gear g shall be calculated by:
fTg = 1 – ηTg
3.1.1.6.
The torque dependent loss Tl,inTg on the input shaft for gear g shall be calculated by:
Tl,inTg = fTg * Tin
3.1.1.7.
The torque dependent efficiency of the planetary range section in low range state for the special case of transmissions consisting of a countershaft-type main section in series with a planetary range section (with non-rotating ring gearwheel and the planet carrier connected to the output shaft) may, alternatively to the procedure described in 3.1.1.8., be calculated by:
ηlowrange1 ηm,ring ηm,sun
zring
zsun
1
zring
zsun
where:
ηm,ringTorque dependent efficiency of the ring-to-planet gear mesh = 99,3 % [-]
ηm,sunTorque dependent efficiency of the planet-to-sun gear mesh = 98,6 % [-]
zsunNumber of teeth of the sun gearwheel of the range section [-]
zringNumber of teeth of the ring gearwheel of the range section [-]
The planetary range section shall be regarded as an additional gear mesh within the countershaft main section, and its torque dependent efficiency ηlowrange shall be included in the determination of the total torque dependent efficiencies ηTg for the low-range gears in the calculation in 3.1.1.4.
3.1.1.8.
For all other transmission types with more complex split power flows and/or planetary gear sets (e.g. a conventional automatic planetary transmission), the following simplified method shall be used to determine the torque dependent efficiency. The method covers transmission systems composed of ordinary, non-planetary gear sets and/or planetary gear sets of ring-planet-sun type. Alternatively the torque dependent efficiency may be calculated based on VDI Regulation No. 2157. Both calculations shall use the same constant gear mesh efficiency values defined in 3.1.1.2.
In this case, for each indirect gear g, the following steps shall be performed:
3.1.1.9.
Assuming 1 rad/s of input speed and 1 Nm of input torque, a table of speed (Ni) and torque (Ti) values for all gearwheels with a fix rotational axis (sun gearwheels, ring gearwheels and ordinary gearwheels) and planet carriers shall be created. Speed and torque values shall follow the right-hand rule, with engine rotation as the positive direction.
3.1.1.10.
For each planetary gear set, the relative speeds sun-to-carrier and ring-to-carrier shall be calculated by:
Nsun–carrier = Nsun – Ncarrier
Nring–carrier = Nring – Ncarrier
where:
NsunRotational speed of sun gearwheel [rad/s]
NringRotational speed of ring gearwheel [rad/s]
NcarrierRotational speed of carrier [rad/s]
3.1.1.11.
The loss-producing powers in the gear meshes shall be computed in the following way:
For each ordinary, non-planetary gear set, the power P shall be calculated by:
P1 = N1 · T1
P2 = N2 · T2
where:
PPower of gear mesh [W]
NRotational speed of gearwheel [rad/s]
TTorque of gearwheel [Nm]
For each planetary gear set, the virtual power of sun Pv,sun and ring gearwheels Pv,ring shall be calculated by:
Pv,sun = Tsun · (Nsun – Ncarrier) = Tsun · Nsun/carrier
Pv,ring = Tring · (Nring – Ncarrier) = Tring · Nring/carrier
where:
Pv,sunVirtual power of sun gearwheel [W]
Pv,ringVirtual power of ring gearwheel [W]
TsunTorque of sun gearwheel [Nm]
TcarrierTorque of carrier [Nm]
TringTorque of ring gearwheel [Nm]
Negative virtual power results shall indicate power leaving the gear set, positive virtual power results shall indicate power going into the gear set.
The loss-adjusted powers Padj of the gear meshes shall be computed in the following way:
For each ordinary, non-planetary gear set, the negative power shall be multiplied by the appropriate torque dependent efficiency ηm:
Pi > 0 ⇒ Pi,adj = Pi
Pi < 0 ⇒ Pi,adj = Pi · ηmi
where:
PadjLoss-adjusted powers of the gear meshes [W]
ηmTorque dependent efficiency (appropriate to gear mesh; see 3.1.1.2.) [-]
For each planetary gear set, the negative virtual power shall be multiplied by the torque-dependent efficiencies of sun-to-planet ηmsun and ring-to-planet ηmring:
Pv,i ≥ 0 ⇒ Pi,adj = Pv,i
Pv,i < 0 ⇒ Pi,adj = Pi · ηmsun · ηmring
where:
ηmsunTorque dependent efficiency of sun-to-planet [-]
ηmringTorque dependent efficiency of ring-to-planet [-]
3.1.1.12.
All loss-adjusted power values shall be added up to the torque dependent gear mesh power loss Pm,loss of the transmission system referring to the input power:
Pm,loss = ΣPi,adj
where:
iAll gearwheels with a fix rotational axis [-]
Pm,lossTorque dependent gear mesh power loss of the transmission system [W]
3.1.1.13.
The torque dependent loss coefficient for bearings,
fT,bear = 1 – ηbear = 1 – 0,995 = 0,005
and the torque dependent loss coefficient for the gear mesh
fT,gearmesh
Pm,loss
Pin
Pm,loss
1Nm 1
rad
s
shall be added to receive the total torque dependent loss coefficient fT for the transmission system:
fT = fT,gearmesh + fT,bear
where:
fTTotal torque dependent loss coefficient for the transmission system [-]
fT,bearTorque dependent loss coefficient for the bearings [-]
fT,gearmeshTorque dependent loss coefficient for the gear meshes [-]
PinFixed input power of the transmission; Pin = (1 Nm * 1 rad/s) [W]
3.1.1.14.
The torque dependent losses on the input shaft for the specific gear shall be calculated by:
Tl,inT = fT * Tin
where:
Tl,inTTorque dependent loss related to input shaft [Nm]
TinTorque at the input shaft [Nm]
3.1.2.
The torque independent losses shall be measured in accordance with the procedure described in the following.
The transmission used for the measurements shall be in accordance with the drawing specifications for series production transmissions and shall be new.
Modifications to the transmission to meet the testing requirements of this Annex, e.g. for the inclusion of measurement sensors or adaption of an external oil conditioning system are permitted.
The tolerance limits in this paragraph refer to measurement values without sensor uncertainty.
Total tested time per transmission individual and gear shall not exceed 5 times the actual testing time per gear (allowing re-testing of transmission if needed due to measuring or rig error).
The same transmission individual may be used for a maximum of 10 different tests, e.g. for tests of transmission torque losses for variants with and without retarder (with different temperature requirements) or with different oils. If the same transmission individual is used for tests of different oils, the recommended factory fill oil shall be tested first.
It is not permitted to run a certain test multiple times to choose a test series with the lowest results.
Upon request of the approval authority the applicant for a certificate shall specify and prove the conformity with the requirements defined in this Annex.
To subtract influences caused by the test rig setup (e.g. bearings, clutches) from the measured torque losses, differential measurements are permitted to determine these parasitic torques. The measurements shall be performed at the same speed points and same test rig bearing temperature(s) ± 3 K used for the testing. The torque sensor measurement uncertainty shall be below 0,3 Nm.
On request of the applicant a run-in procedure may be applied to the transmission. The following provisions shall apply for a run-in procedure.
3.1.2.3.1.
The procedure shall not exceed 30 hours per gear and 100 hours in total.
3.1.2.3.2.
The application of the input torque shall be limited to 100 % of maximum input torque.
3.1.2.3.3.
The maximum input speed shall be limited by the specified maximum speed for the transmission.
3.1.2.3.4.
The speed and torque profile for the run-in procedure shall be specified by the manufacturer.
3.1.2.3.5.
The run-in procedure shall be documented by the manufacturer with regard to run-time, speed, torque and oil temperature and reported to the Approval authority.
3.1.2.3.6.
The requirements for the ambient temperature (3.1.2.5.1.), measurement accuracy (3.1.4.), test set-up (3.1.8.) and installation angle (3.1.3.2) shall not apply for the run-in procedure.
3.1.2.4.1.
Pre-conditioning of the transmission and the test rig equipment to achieve correct and stable temperatures before the run-in and testing procedures is allowed.
3.1.2.4.2.
The pre-conditioning shall be performed without applied torque to the non driven shaft.
3.1.2.4.3.
The maximum input speed shall be limited by the specified maximum speed for the transmission.
3.1.2.4.4.