This Annex describes the provisions regarding declaration of technologies and other relevant input information on auxiliary systems for heavy duty vehicles for the purpose of the determination of vehicle specific CO2 emissions.
The power consumption of the following auxiliary types shall be considered within the simulation tool by using technology specific average generic models for power consumption:
Engine cooling fan
Steering system
Electric system
Pneumatic system
Heating, ventilation and air conditioning (HVAC) system
Transmission Power Take Off (PTO)
The generic values are integrated in the simulation tool and automatically used based on the relevant input information in accordance with the provisions in this Annex. The related input data formats for the simulation tool are described in Annex III. For a clear reference, the three-digit parameter IDs used in Annex III are also listed in this Annex.’;
For the purposes of this Annex the following definitions shall apply. The related auxiliary type is stated in brackets.
‘crankshaft mounted’ fan means a fan installation where the fan is driven in the prolongation of the crankshaft, often by a flange (engine cooling fan);
‘belt or transmission driven’ fan means a fan that is installed in a position where additional belt, tension system or transmission is needed (engine cooling fan);
‘hydraulic driven’ fan means a fan propelled by hydraulic oil, often installed away from the engine. A hydraulic system with oil system, pump and valves are influencing losses and efficiencies in the system (engine cooling fan);
‘electrically driven’ fan means a fan propelled by an electric motor. The efficiency for complete energy conversion, included in/out from battery, is considered (engine cooling fan);
‘electronically controlled visco clutch’ means a clutch in which a number of sensor inputs together with SW logic are used to electronically actuate the fluid flow in the visco clutch (engine cooling fan);
‘bimetallic controlled visco clutch’ means a clutch in which a bimetallic connection is used to convert a temperature change into mechanical displacement. The mechanical displacement is then working as an actuator for the visco clutch (engine cooling fan);
‘discrete step clutch’ means a mechanical device where the grade of actuation can be made in distinct steps only (not continuous variable) (engine cooling fan);
‘on/off clutch’ means a mechanical clutch which is either fully engaged or fully disengaged (engine cooling fan);
‘variable displacement pump’ means a device that converts mechanical energy to hydraulic fluid energy. The amount of fluid pumped per revolution of the pump can be varied while the pump is running (engine cooling fan);
‘constant displacement pump’ means a device that converts mechanical energy to hydraulic fluid energy. The amount of fluid pumped per revolution of the pump cannot be varied while the pump is running (engine cooling fan);
‘electric motor control’ means the use of an electric motor to propel the fan. The electrical machine converts electrical energy into mechanical energy. Power and speed are controlled by conventional technology for electric motors (engine cooling fan);
‘fixed displacement pump (default technology)’ means a pump having an internal limitation of the flow rate (steering system);
‘fixed displacement pump with electronic control’ means a pump using an electronic control of the flow rate (steering system);
‘dual displacement pump’ means a pump with two chambers (with the same or different displacement) mechanical internal limitation of flow rate (steering system);
‘dual displacement pump with electronic control’ means a pump with two chambers (with the same or different displacement) which can be combined or where under specific conditions only one of these is used. The flow rate is electronically controlled by a valve (steering system);
‘variable displacement pump mech. controlled’ means a pump where the displacement is mechanically controlled internally (internal pressure scales) (steering system);
‘variable displacement pump elec. controlled’ means a pump where the displacement is electronically controlled (steering system);
‘electric driven pump’ means a steering system driven by an electric motor with continuously recirculating hydraulic fluid (steering system);
‘full electric steering gear’ means a steering system driven by an electric motor without continuously recirculating hydraulic fluid (steering system);
-
‘air compressor with energy saving system’ or ‘ESS’ means a compressor reducing the power consumption during blow off, e.g. by closing intake side, ESS is controlled by system air pressure (pneumatic system);
‘compressor clutch (visco)’ means a disengageable compressor where the clutch is controlled by the system air pressure (no smart strategy), minor losses during disengaged state caused by visco clutch (pneumatic system);
‘compressor clutch (mechanically)’ means a disengageable compressor where the clutch is controlled by the system air pressure (no smart strategy) (pneumatic system);
‘air management system with optimal regeneration’ or ‘AMS’ means an electronic air processing unit that combines an electronically controlled air dryer for optimised air regeneration and an air delivery preferred during overrun conditions (requires a clutch or ESS) (pneumatic system).
‘light emitting diode’ or ‘LED’ means semiconductor devices that emit visible light when an electrical current passes through them (electric system);
-
‘power take-off’ or ‘PTO’ means a device on a transmission or an engine to which an optional power consuming device (‘consumer’), e.g., a hydraulic pump, can be connected; a power take-off is usually optional (PTO);
‘power take-off drive mechanism’ means a device in a transmission that allows the installation of a power take-off (PTO);
‘engaged gearwheel’ means a gearwheel which is engaged with running shafts of either the engine or transmission while the PTO clutch (if applicable) is open (PTO);
‘tooth clutch’ means a (manoeuvrable) clutch where torque is transferred mainly by normal forces between mating teeth. A tooth clutch can either be engaged or disengaged. It is operated in load-free conditions only (e.g. at gear shifts in a manual transmission) (PTO);
‘synchroniser’ means a type of tooth clutch where a friction device is used to equalise the speeds of the rotating parts to be engaged (PTO);
‘multi-disc clutch’ means a clutch where several friction linings are arranged in parallel whereby all friction pairs get the same pressing force. Multi-disc clutches are compact and can be engaged and disengaged under load. They may be designed as dry or wet clutches (PTO);
‘sliding wheel’ means a gearwheel used as shift element where the shifting is realised by moving the gearwheel on its shaft into or out of the gear mesh of the mating gear (PTO);
‘discrete step clutch (off + 2 stages)’ means a mechanical device where the grade of actuation can be made in two distinct steps plus off only (not continuous variable) (engine cooling fan);
‘discrete step clutch (off + 3 stages)’ means a mechanical device where the grade of actuation can be made in three distinct steps plus off only (not continuous variable) (engine cooling fan);
‘ratio compressor to engine’ means the forward gear ratio of the air compressor to the speed of the engine without slip (pneumatic system);
‘air suspension control mechanically’ means an air supension system in which the air suspension control valves are operated mechanically without electronics and software (pneumatic system);
‘air suspension control electronically’ means an air supension system in which a number of sensor inputs together with software logic are used to electronically actuate the air suspension control valves (pneumatic system);
‘pneumatic SCR reagent dosing’ means that compressed air is used for dosing reagent into the exhaust system (pneumatic system);
‘door drive technology pneumatic’ means that the passenger doors of the vehicle are operated with compressed air (pneumatic system);
‘door drive technology electric’ means that the passenger doors of the vehicle are operated with an electric motor or with an electrohydraulic system (pneumatic system);
‘door drive technology mixed’ means that both ‘door drive technology pneumatic’ and ‘door drive technology electric’ are installed in the vehicle (pneumatic system);
‘smart regeneration system’ means a pneumatic system in which the regeneration air demand is optimised with respect to the quantity of dried air that is produced (pneumatic system);
‘smart compression system’ means a pneumatic system in which the air delivery is electronically controlled with preferred air delivery during overrun conditions (pneumatic system);
‘interior lights’ means the lights within the passenger compartment that are installed to fulfil the requirements of paragraph 7.8. (artificial interior lighting) in Annex 3 to UN Regulation No. 107 [Regulation No 107 of the Economic Commission for Europe of the United Nations (UNECE) – Uniform provisions concerning the approval of category M2 or M3 vehicles with regard to their general construction (OJ L 52, 23.2.2018, p. 1).] (electric system);
‘day running lights’ means the ‘daytime running lamp’ in accordance with paragraph 2.7.25 of UN Regulation No. 48 [Regulation No 48 of the Economic Commission for Europe of the United Nations (UNECE) – Uniform provisions concerning the approval of vehicles with regard to the installation of lighting and light-signalling devices (OJ L 14, 16.1.2019, p. 42).] (electric system);
‘position lights’ means the ‘side marker lamp’ in accordance with paragraph 2.7.24 of UN Regulation No. 48 (electric system);
‘brake lights’ means the ‘stop lamp’ in accordance with paragraph 2.7.12 of UN Regulation No. 48 (electric system);
‘headlights’ means the ‘passing-beam (dipped-beam) headlamp’ in accordance with paragraph 2.7.10 of UN Regulation No. 48, and the ‘driving-beam (main-beam) headlamp’ in accordance with paragraph 2.7.9 of UN Regulation No. 48 (electric system);
‘alternator’ means an electric machine to charge the battery and to supply electric power to the electrical auxiliary system when the vehicle’s internal combustion engine is running. An alternator can not contribute to propulsion of the vehicle (electric system);
‘smart alternator system’ means a system of one ore more alternators in combination with one or more dedicated REESS which is electronically controlled with preferred generation of electic energy during overrun conditions (electric system);
‘heating, ventilation and air conditioning system’ or HVAC system means a system that can actively heat and/or actively cool down and exchange or replace air to provide improved air qualityfor the passenger and/or the driver compartment (HVAC system);
‘HVAC system configuration’ means a combination of HVAC system components in accordance with Table 13 of this Annex (HVAC system);
‘thermal comfort system for passenger compartment’ means a system that uses fans to circulate air within the vehicle or blows fresh air into the vehicle and the air volume flow can at least be actively cooled or heated. The air is distributed from the roof of the vehicle and in the case of double deckers, in both floors. In the case of open top double deckers, in the lower deck (HVAC system);
‘number of heat pumps for passenger compartment’ means the number of heat pumps that are installed in the vehicle to heat up and/or cool down cabin air or fresh air supplied to the passenger compartment. If a heat pump is used for the passenger and for the driver compartment it is counted for the passenger compartment only (HVAC system). If different heat pumps for heating and cooling are installed, the number of heat pumps shall be defined by the lower number of both separate cases – i.e. the number of heat pumps for cooling and the number of heat pumps for heating shall be considered separately (e.g. in the case of 2 heat pumps for cooling and 1 heat pump for heating: only 1 heat pump shall be considered);
‘air conditioning system for driver compartment’ means that a system is installed in the vehicle that can cool down the cabin air or fresh air supplied to the driver or driver compartment (HVAC system);
‘air conditioning system for passenger compartment’ means that a system is installed in the vehicle that can cool down the cabin air or fresh air supplied to the passenger compartment (HVAC system);
‘independent heat pump for driver compartment’ means that a heat pump is installed in the vehicle that is only used for the driver compartment (HVAC system);
‘heat pump 2-stage’ means a heat pump where the grade of actuation can be made in two steps only but not continuous variable (HVAC system);
‘heat pump 3-stage’ means a heat pump where the grade of actuation can be made in three steps only but not continuous variable (HVAC system);
‘heat pump 4-stage’ means a heat pump where the grade of actuation can be made in four steps only but not continuous variable (HVAC system);
‘heat pump continuous’ means a heat pump where the grade of actuation is continuously variable or where the air conditioning compressor is driven by an electric motor with continuously variable speed (HVAC system);
‘auxiliary heater power’ as stated on the label defined in paragraph 4 of Annex 7 to UN Regulation No. 122 [Regulation No 122 of the Economic Commission for Europe of the United Nations (UN/ECE) – Uniform technical prescriptions concerning the approval of vehicles of categories M, N and O with regard to their heating systems (OJ L 19, 24.1.2020, p. 42).] (HVAC system);
‘double glazing’ means windows of the passenger compartment that consist of two glass window panes that are separated by gas filled space or by vacuum. In the case of several types of windows within the passenger compartment, the predominant window type with regards to surface area has to be selected. For the assessment of the predominant window type the windscreen, the rear window, the driver side-window(s), windows within doors, windows above and in front of the front axle (see Figure 1 for examples) as well as tiltable windows, shall not be considered (HVAC system);
‘heat pump’ means a system that uses a refrigerant in a circular process to transfer thermal energy from the environment to the passenger compartment and/or the driver compartment and/or transfers thermal energy in the opposite direction (cooling and/or heating functionality) with a coefficient of performance larger than 1 (HVAC system);
‘R-744 heat pump’ means a continuous (i.e. electrically driven) heat pump which uses R-744 refrigerant as working medium (HVAC system);
‘non R-744 heat pump’ means a heat pump which uses another working medium than R-744 refrigerant. For the possible grade of actuation (2-stage, 3-stage, 4-stage, continuous), the definitions (56) to (59) shall apply (HVAC system);
‘adjustable coolant thermostat’ means a coolant thermostat which characteristics are influenced by at least one additional input besides the coolant temperature, e.g. active electric heating of the thermostat (HVAC system);
‘adjustable auxiliary heater’ means a fuel-operated heater with at least 2 levels of heating capacity besides ‘off’ that can be controlled depending on the required heating system capacity in the bus (HVAC system);
‘engine waste gas heat exchanger’ means a heat exchanger that uses the thermal energy of engine waste gas to heat the cooling circuit (HVAC system);
‘separate air distribution ducts’ means one or multiple air channels connected to a thermal comfort system to distribute conditioned air evenly to the passenger compartment. Air channels may include loud speakers or HVAC water supply and electric harness. Reservoirs for compressed airs shall not be installed within this/these channel/s. By this model parameter the simulation tool considers reduced heat transfer losses to the ambient or components within the channel. For HVAC configurations 8, 9 and 10 in vehicle groups 31, 33, 35, 37 and 39, this input shall be set to ‘true’ as those configurations benefit from reduced losses as cooled air is directly blown into vehicle interior even without any air channel. For all HVAC configurations in vehicle groups 32, 34, 36, 38 and 40 this parameter shall be set to ‘true’ as this is state-of-the-art (HVAC system);
‘electrically driven compressor’ means a compressor driven by an electric motor (pneumatic system);
‘water electric heater’ means a device using electric energy to heat up the coolant of the vehicle with a coefficient of performance lower than 1 and that is actively used for the heating functionality during vehicle operation on road (HVAC system);
‘air electric heater’ means a device using electric energy to heat up the air of the passenger and/or driver compartment with a coefficient of performance lower than 1 (HVAC system);
‘other heating technology’ means any fully electric technology used for heating up the passenger and/or driver compartment not covered by the technologies in definitons (62), (70) or (71) (HVAC system);
‘lead-acid battery – conventional’ means a lead-acid battery where none of the definitions (74) or (75) applies (electric system);
‘lead-acid battery –AGM’ (Absorbed Glass Mat) means lead-acid batteries where glass fibre mats soaked in electrolyte are used as separators between the negative and positive plates (electric system);
‘lead-acid battery – gel’ means lead-acid batteries where a silica gelling agent is mixed into the electrolyte (electric system);
‘Li-ion battery - high power’ means a Li-ion battery where the numerical ratio between rated maximum current in [A] and the rated capacity in [Ah] is equal to or larger than 10 (electric system);
‘Li-ion battery - high energy’ means a Li-ion battery where the numerical ratio between rated maximum current in [A] and the rated capacity in [Ah] is less than 10 (electric system);
‘capacitor with DC/DC converter’ means an (ultra) capacitor electrical energy storage unit combined with a DC/DC unit that adapts the voltage level and controls the current to and from the electric consumer board net (electric system);
‘articulated bus’ means a heavy bus that is an incomplete vehicle, complete vehicle or completed vehicle consisting of at least two rigid sections connected to each other by an articulated section. Connection and disconnection of the sections are to be possible only in a workshop. For the complete or completed heavy buses of this type of vehicle, the articulated section shall permit the free movement of travellers between the rigid sections.
The information on engine cooling fan technology shall be provided based on the applicable combinations of fan drive and fan control technology as described in Table 4 below.
If a new technology within a fan drive cluster (e.g. crankshaft mounted) cannot be found in the list, the technology allocated to ‘default for fan drive cluster’ shall be provided.
If a new technology cannot be found in any fan drive cluster the technology allocated to ‘default overall’ shall be provided.
X: applicable, DC: default for fan drive cluster, DO: default overall
Fan drive cluster | Fan control | Medium and heavy lorries | Heavy buses
Crankshaft mounted | Electronically controlled visco clutch | X | X
Bimetallic controlled visco clutch | X (DC) | X
Discrete step clutch | X |
Discrete step clutch (off + 2 stages) | | X
Discrete step clutch (off + 3 stages) | | X
On/off cluch | X | X (DC, DO)
Belt driven or driven via transmission | Electronic controlled visco clutch | X | X
Bimetallic controlled visco clutch | X (DC) | X
Discrete step clutch | X |
Discrete step clutch (off + 2 stages) | | X
Discrete step clutch (off + 3 stages) | | X
On/off cluch | X | X (DC)
Hydraulically driven | Variable displacement pump | X | X
Constant displacement pump | X (DC, DO) | X (DC)
Electrically driven | Electric motor control | X (DC) | X (DC)
The technology of the steering system shall be provided in accordance with Table 5 per each active steered axle on the vehicle.
If a new technology within a steering technology cluster (e.g. mechanically driven) cannot be found in the list, the technology allocated to ‘default for steering technology cluster’ shall be provided. If a new technology cannot be found in any steering technology cluster the technology allocated to ‘default overall’ shall be provided.
X: applicable, DC: default for steering technology cluster, DO: default overall
Steering technology cluster | Technology | Medium and heavy lorries | Heavy buses
Mechanically driven | Fixed displacement | X (DC, DO) | X (DC, DO)
Fixed displacement, electronical control | X | X
Dual displacement pump | X | X
Dual displacement pump with electronic control | X | X
Variable displacement, mechanical control | X | X
Variable displacement, electronical control | X | X
Electric | Electric driven pump | X (DC) | X (DC)
Full electric steering gear | X | X
The technology of the electric system shall be provided in accordance with
Table 6.
If the technology used in the vehicle is not listed, ‘standard technology’ shall be provided to the simulation tool.
Technology
Standard technology
Standard technology - LED headlights
The technology of the electric system shall be provided in accordance with Table 7.
Electric system cluster | Parameter | Parameter (ID) | Input to the simulation tool | Explanations
Alternator | Alternator technology | P294 | conventional / smart / no alternator |
‘smart’ shall be declared for systems fulfilling the definitions as given in point 2(48);
‘no alternator’ is applicable for HEVs which do not have an alternator in the electric auxiliary system. For PEV or FCHV no input is required.
Smart alternator – maximum rated current | P295 | value in [A] |