ANNEX VIII, Regulation (EU) 2015/504

In forcesince 7 Aug 2018cited 2×

1.1.

For each of the regulatory acts listed in Annex I to Regulation (EU) No 167/2013, the template of the test reports shall be drawn up by the technical service in accordance with its rules of good practice.

1.2.

The format shall be designed to accommodate each type of test carried out and to minimise the possibility of misunderstanding or misuse. Especial attention should be given with regard to the presentation of the test data and ease of assimilation by the reader.

1.2.1.

The headings should be standardised as far as possible.

1.3.

The test report shall be drafted in one or more of the official Union languages determined by the approval authority.

1.3.1.

Where a test has been carried out in a Member State other than the one handling the approval application, the approval authority may require the applicant to provide a certified translation of the test report.

1.4.

Only authenticated copies of a test report shall be submitted.

1.5.

If calibration is required for performing the tests, the corresponding calibration certificate(s) shall be appended to the test reports. The calibration certificate(s) shall comply with the provisions laid down in point 5.10 (Reporting the results) of Standard EN ISO/IEC 17025:2005 (General requirements for the competence of testing and calibration laboratories).

The test reports shall include the following information:

2.1.

a title (e.g. ‘Test Report on …’);

2.2.

the name and address of the technical service, and the location where the tests and/or calibrations were carried out, if different from the address of the technical service;

2.3.

an unique identification of the test report or calibration certificate (such as the serial number), and on each page an identification in order to ensure that the page is recognised as a part of the test report or calibration certificate, and a clear identification of the end of the test report or calibration certificate;

2.3.1.

hard copies of test reports and calibration certificates should also include the page number and total number of pages;

2.4.

a statement specifying that the test report shall not be reproduced except in full, without written approval of the technical service;

2.5.

general information concerning vehicles, as laid down in section 1 of the information document data entries laid down in point 5 of Part B of Annex I to this Regulation;

2.5.1.

The information must indicate the variant and/or version to which it applies. One version shall not have more than one test result. However, a combination of several test results per version, indicating the worst case, is permissible. In this case, a note shall state that for items marked (*) only worst-case results are given.

2.6.

general information concerning the system(s), component(s) or separate technical unit(s) tested vehicles, as laid down in section 2 of the information document data entries laid down in point 5 of Part B of Annex I to this Regulation;

2.7.

the identification number and description of the parts and equipment having a significant influence role in determining the test results;

2.8.

identification of the test method used;

2.8.1.

the date of receipt of the test or calibration item(s) where this is critical to the validity and application of the results, and the date(s) of performance of the test or calibration;

2.9.

ambient conditions influencing the test: atmospheric pressure (kPa); relative humidity (%); ambient temperature (K); wind speed and direction on test track (km/h), etc.;

2.10.

condition of the vehicle influencing the test, such as fitted accessories; actual masses; test voltage; tyre sizes; tyre pressures; etc.;

2.11.

detailed description of the characteristics of the vehicle, system, component or separate technical unit tested having relevant impact on the test results;

2.12.

when the tests are conducted on a vehicle, system, component or technical unit which combines a number of least favourable features concerning the required performance level (the worst-case), the test report shall include a reference stating how the selection was made by the manufacturer in agreement with the technical service;

2.13.

the measurement results specified in the relevant regulatory acts and, where required, the limits or thresholds to be met and the units of measurement;

2.14.

with regard to each measurement mentioned in point 2.12, the relevant decision: passed or failed;

2.15.

where relevant, a statement to the effect that the results relate only to the items tested or calibrated;

2.16.

a detailed statement of compliance with the various provisions to be met, i.e. provisions for which measurements were not required;

2.17.

when test methods other than those prescribed in the regulatory acts are permitted, the report shall describe the test method used. The same applies when alternative provisions to those in the regulatory acts may be applied;

2.18.

the number of photographs to be taken during testing shall be decided by the approval authority. In the case of virtual testing, screen prints or other suitable evidence may replace photographs;

2.19.

Technical service responsible for carrying out the test and the name(s), function(s) and signature(s) or equivalent identification of person(s) authorising the test report;

2.20.

Conclusions drawn up;

2.21.

when opinions, assumptions and interpretations have been made, the technical service shall document the basis upon which the opinions and interpretations have been made and they shall be documented properly and marked as such in the test report;

2.21.1.

where necessary for the interpretation of the test results, include the following:

(a)

deviations from, additions to, or exclusions from the test method, and information on specific test;

(b)

where relevant, a statement of compliance/non-compliance with requirements and/or specifications;

(c)

where applicable, a statement on the estimated uncertainty of measurement; information on uncertainty is needed in test reports when it is relevant to the validity or application of the test results, when a manufacturer's instruction so requires, or when the uncertainty affects compliance to a specification limit;

(d)

where appropriate and needed, opinions and interpretations, in accordance with point 2.21.2;

(e)

any additional information.

2.21.2.

Opinions and interpretations included in a test report may comprise, but not be limited to, the following:

(a)

an opinion on the statement of compliance/noncompliance of the results with the requirements;

(b)

recommendations on how to use the results;

(c)

guidance to be used for improvements;

(d)

in case that the opinions and interpretations communicated by direct dialogue with the manufacturer, such dialogue should be written down.

3.1.

With regard to technical requirements set out in the delegated acts adopted pursuant to Regulation (EU) No 167/2013 and based on

(a)

UNECE Regulations, e.g. UNECE Regulation No 13 on uniform provisions concerning the approval of vehicles of categories M, N and O with regard to braking (OJ L 257, 30.9.2010, p. 1),

(b)

OECD standard codes for the official testing of protective structures on agricultural and forestry tractors, e.g. OECD Code 7 for the official testing of rear mounted roll-over protective structures on narrow-track wheeled agricultural and forestry tractors, or

(c)

EN/ISO standards, e.g. EN 15695-1 on cab classification, requirements and test procedures for protection of the driver against hazardous substances,

test reports shall contain the same technical information and shall display it in the same order as in the templates of the test reports set out in the UNECE Regulation, OECD Code and EN/ISO standard.

3.2.

Test reports issued under Directive 2003/37/EC, Regulation (EU) 2016/1628, Regulation (EC) No 595/2009, Directive 2007/46/EC or international regulations referred to in Chapter XIII of Regulation (EU) No 167/2013 and the delegated and implementing acts adopted pursuant to that Regulation shall be accepted for the purposes of type-approval under Regulation (EU) No 167/2013 for the following components and separate technical units under the conditions indicated in Table 8-1:

[Directive 2000/25/EC of the European Parliament and of the Council of 22 May 2000 on action to be taken against the emission of gaseous and particulate pollutants by engines intended to power agricultural or forestry tractors and amending Council Directive 74/150/EEC (OJ L 173, 12.7.2000, p. 1).] [Commission Directive 2014/43/EU of 18 March 2014 amending Annexes I, II and III to Directive 2000/25/EC of the European Parliament and of the Council on action to be taken against the emission of gaseous and particulate pollutants by engines intended to power agricultural or forestry tractors (OJ L 82, 20.3.2014, p. 12).] [Commission Directive 2012/46/EU of 6 December 2012 amending Directive 97/68/EC of the European Parliament and of the Council on the approximation of the laws of the Member States relating to measures against the emission of gaseous and particulate pollutants from internal combustion engines to be installed in non-road mobile machinery (OJ L 353, 21.12.2012, p. 80).] [Directive 2009/64/EC of the European Parliament and of the Council of 13 July 2009 on the suppression of radio interference produced by agricultural or forestry tractors (electromagnetic compatibility) (OJ L 216, 20.8.2009, p. 1).] [Directive 2009/63/EC of the European Parliament and of the Council of 13 July 2009 on certain parts and characteristics of wheeled agricultural or forestry tractors (OJ L 241, 19.8.2009, p. 23).] [Council Directive 89/297/EEC of 13 April 1989 on the approximation of the laws of the Member States relating to the lateral protection (side guards) of certain motor vehicles and their trailers (OJ L 124, 13.4.1989, p. 1).] [Council Directive 70/221/EEC of 20 March 1970 on the approximation of the laws of the Member States relating to liquid fuel tanks and rear protective devices for motor vehicles and their trailers (OJ L 76, 6.4.1970, p. 23).] [Commission Directive 2006/20/EC of 17 February 2006 amending, for the purposes of its adaptation to technical progress, Council Directive 70/221/EEC concerning fuel tanks and rear underrun protection of motor vehicles and their trailers (OJ L 48, 18.2.2006, p. 16).] [Directive 2009/144/EC of the European Parliament and of the Council of 30 November 2009 on certain components and characteristics of wheeled agricultural or forestry tractors (OJ L 27, 30.1.2010, p. 33).] [Commission Directive 2010/52/EU of 11 August 2010 amending, for the purposes of adaptation of their technical provisions, Council Directive 76/763/EEC relating to passenger seats for wheeled agricultural or forestry tractors and Directive 2009/144/EC of the European Parliament and of the Council on certain components and characteristics of wheeled agricultural or forestry tractors (OJ L 213, 13.8.2010, p. 37).] [Council Directive 78/764/EEC of 25 July 1978 on the approximation of the laws of the Member States relating to the driver's seat on wheeled agricultural or forestry tractors (OJ L 255, 18.9.1978, p. 1).] [Commission Directive 1999/57/EC of 7 June 1999 adapting to technical progress Council Directive 78/764/EEC relating to the driver's seat on wheeled agricultural or forestry tractors (OJ L 148, 15.6.1999, p. 35).]

Component/STU | Conditions of acceptance

Component/STU: engine/engine family |

Test report issued under Directive 2000/25 as last amended by Commission Directive 2014/43/EU;

Test report issued under Regulation EU 2016/1628; and

Test report issued under Regulation (EC) No 595/2009

Component / STU: electro-magnetic compatibility of electrical / electronic sub-assemblies |

Test report issued under Directive 2009/64/EC of the European Parliament and of the Council, as far as the testing equipment has been updated in:

Radiated broadband and narrowband electromagnetic emissions from vehicles

Radiated broadband and narrowband electromagnetic emissions from electronic sub-assemblies

The measuring equipment and test site shall comply with the requirements of publication No 16-1 series of the International Special Committee on Radio Interference (CISPR):

Radiated broadband and narrowband electromagnetic emissions from vehicles

Antenna calibration may be according to the method described in CISPR publication No 12, Edition 6, Annex C, and

Test report issued under UNECE Regulation 10, 04 series of amendments, Corrigendum 1 to the Revision 4, supplement 1 to the 04 series of amendments (OJ L 254, 20.9.2012, p. 1.)

Component/STU: ballast masses | Test report issued under Directive 2009/63/EC

Component/STU: lateral and/or rear protective structure |

Test report issued under Directive 89/297/EC (O3- and O4-category vehicles),

Test report issued under UNECE R73, 01 series of amendments (O3- and O4-category vehicles) (OJ L 122, 8.5.2012, p. 1), and

Test report issued under Directive 70/221/EEC, as amended by Commission Directive 2006/20/EC (O-category vehicles)

Component/STU: mechanical coupling |

Test report issued under Directive 2009/144/EC:

Dynamic or Static test method only accepted for vehicles with ‘a’ speed index: maximum design speed not exceeding 40 km/h.

Dynamic test method accepted for vehicles with ‘b’ speed index: maximum design speed exceeding 40 km/h)

STU: roll-over protective structure (ROPS) (dynamic testing) | Test report issued under the OECD standard code for the official testing of protective structures on agricultural and forestry tractors (dynamic test), OECD Code 3, Edition 2012 of Fe2012

STU: roll-over protective structure (ROPS) (track-laying tractors) | Test reports issued under the OECD standard code for the official testing of protective structures on agricultural and forestry track-laying tractors, OECD Code 8, Edition 2012 of February 2012

STU: roll-over protective structure (ROPS) (static testing) | Test reports issued under the OECD standard Code for the official testing of protective structures on agricultural and forestry tractors (static test), OECD Code 4, Edition 2012 of February 2012

STU: roll-over protective structure (ROPS) (front mounted roll-over protective structures on narrow-track tractors) | Test reports in conformity with the OECD standard code for the official testing of front mounted roll-over protective structures on narrow-track wheeled agricultural and forestry tractors, OECD Code 6, Edition 2012 of February 2012

STU: roll-over protective structure (ROPS) (rear mounted roll-over protective structures on narrow-track tractors) | Test reports in conformity with the OECD standard code for the official testing of rear mounted roll-over protective structures on narrow-track wheeled agricultural and forestry tractors, OECD Code 7, Edition 2012 of February 2012

STU: falling objects protective structure (FOPS) | Test report issued under Directive 2009/144/EC as amended by Commission Directive 2010/52/EU or OECD standard code for the official testing of falling object protective structures on agricultural and forestry tractors Code 10 — Edition 2009 of February 2009

Component/STU: driver's seat | Test report issued under Council Directive 78/764/EEC as amended by Commission Directive 1999/57/EC

Component/STU: safety belts | Test report issued under UNECE Regulation No 16 Supplement 1 to the 06 series of amendments (OJ L 233, 9.9.2011, p. 1)

STU: protection against penetrating objects (OPS) |

Test report issued under Directive 2009/144/EC as amended by Commission Directive 2010/52/EU, and

Test report issued under UNECE Regulation No 43 Supplement 12 to the 00 series of amendments, Annex 14 (OJ L 230, 31.8.2010, p. 119)

3.3.

Test reports on braking

The models of the test reports for braking are set out in Appendices 1 to 5.

3.4.

Additional information to be stated in model test report form for the alternative procedures for Type-I and Type-III tests for towed vehicle brakes (Annex VII, Appendix 1 to Regulation (EU) 2015/68) set out in Appendix 1

3.4.1. Test report number

The test report number consists of two parts: a base part and a suffix which identifies the issue level of the test report.

3.4.1.1. The base part, consisting of a maximum of 20 characters, and suffix shall be clearly separated from each other using e.g. a dot or slash.

3.4.1.2. The base part of the test report number shall only cover brakes with the same brake identifier and the same brake factor.

3.4.2. Test code

In addition to the test report number a ‘test code’ consisting of up to eight characters (e.g. ABC123) shall indicate the test results applicable to the identifiers and the test specimen, which is described by the details given in point 3.7. of Appendix 1 to Annex VII to Regulation (EU) 2015/68.

Test reports for engines shall be drafted in accordance with the single format of the test report set out in Annex VI to Implementing Regulation (EU) 2017/656.

Test Report No. …

Base part: ID4- …

Suffix: …

1.

General …

1.1. Axle manufacturer (name and address): …

1.1.1. Make of axle manufacturer: …

1.2. Brake manufacturer (name and address): …

1.2.1. Brake identifier ID2-: …

1.2.2. Automatic brake adjustment device: integrated/non-integrated [Strike out what does not apply.]

1.3. Manufacturer's Information Document:

2.

Test Record

The following data has to be recorded for each test:

2.1. Test code: …

2.2. Test specimen: (precise identification of the variant tested related to the Manufacturer's Information Document.)

2.2.1. Axle

2.2.1.1. Axle identifier: ID1- …

2.2.1.2. Identification of tested axle: …

2.2.1.3. Test axle load (Fe identifier): ID3- … daN

2.2.2. Brake

2.2.2.1. Brake identifier: ID2- …

2.2.2.2. Identification of tested brake: …

2.2.2.3. Maximum stroke capability of the brake [Applies to disc brakes only.]: …

2.2.2.4. Effective length of the cam shaft3: …

2.2.2.5. Material variation as per point 3.8 (m) of Appendix 1 to Annex VII to Regulation (EU) 2015/68: …

2.2.2.6. Brake drum / disc [Strike out what does not apply.] …

2.2.2.6.1. Actual test mass of disc / drum [Strike out what does not apply.]: …

2.2.2.6.2. Nominal external diameter of disc [Applies to disc brakes only.]: …

2.2.2.6.3. Type of cooling of the disc ventilated/non-ventilated [Strike out what does not apply.]

2.2.2.6.4. With or without integrated hub [Strike out what does not apply.]

2.2.2.6.5. Disc with integrated drum – with or without parking brake function [Strike out what does not apply.] [Applies to disc brakes only.]

2.2.2.6.6. Geometric relationship between disc friction surfaces and disc mounting: …

2.2.2.6.7. Base material: …

2.2.2.7. Brake lining or pad [Strike out what does not apply.]

2.2.2.7.1. Manufacturer: …

2.2.2.7.2. Make: …

2.2.2.7.3. Type: …

2.2.2.7.4. Method of attachment of the lining / pad on the brake shoe / back plate [Strike out what does not apply.]: …

2.2.2.7.5. Thickness of back plate, weight of shoes or other describing information (Manufacturer's Information Document) [Strike out what does not apply.]: …

2.2.2.7.6. Base material of brake shoe / back plate [Strike out what does not apply.]: …

2.2.3. Automatic brake adjustment device (not applicable in the case of integrated automatic brake adjustment device) [Strike out what does not apply.]

2.2.3.1. Manufacturer (name and address): …

2.2.3.2. Make: …

2.2.3.3. Type: …

2.2.3.4. Version: …

2.2.4. Wheel(s) (dimensions see Figures 1A and 1B in the information document of towed vehicle axle and brake with respect to the alternative procedures for Type I and Type III tests)

2.2.4.1. Reference tyre rolling radius (Re) at test axle load (Fe): …

2.2.4.2. Data of the fitted wheel during testing:

Tyre size | Rim size | Xe (mm) | De (mm) | Ee (mm) | Ge (mm)

2.2.5. Lever length le: …

2.2.6. Brake actuator

2.2.6.1. Manufacturer: …

2.2.6.2. Make: …

2.2.6.3. Type: …

2.2.6.4. (Test) Identification number: …

2.3. Test results (corrected to take account of rolling resistance of 0,01·Fe and 0,02·Fe respectively)

2.3.1. In the case of vehicles of categories

R1, R2, S1

‘R3a/R4a/S2a’ [Where these vehicles have been subject to the Type III test (compare point 2.3.1. or 2.3.2.+).]

‘R3b/R4b/S2b’ where the sum of the technically permissible masses per axle does not exceed 10000 kg [Where these vehicles have been subject to the Type III test (compare point 2.3.1. or 2.3.2.+).]

Depending on the maximum design speed and assumed rolling resistance of 0,01 or 0,02 in the following Tables A to C apply:

2.3.1.1 Considered rolling resistance coefficient R = 0,01 (covering also towed vehicles specified in point 2.3.1. above with a maximum design speed exceeding 40 km/h)

Table A

Applicable for all towed vehicle as specified in paragraph 2.3.1 above

Test type

0 | I

Appendix 1 to Annex VII of Regulation (EU) 2015/68, point: | 3.5.1.4. | 3.5.2.2. or 3.5.2.3. | 3.5.2.4.

Test speed | 40 | 40 | 40

Brake actuator pressure pe | | — |

Braking time | — | 2,55 | —

Brake force developed Te | | |

Brake efficiency Te/Fe | | |

Actuator stroke se | | — |

Brake input torque Ce | | — |

Brake input threshold torque C0,e | | |

2.3.1.2 Considered rolling resistance coefficient R = 0,02 (covering towed vehicles Ra and Sa specified in point 2.3.1. above with a maximum design speed not exceeding 40 km/h)

Table B

Alternative test procedure applicable for all towed vehicle of categories Ra and Sa

Test type

0 | I

Annex VII, Appendix 2, paragraph: | 3.5.1.4. | 3.5.2.2. or 3.5.2.3. | 3.5.2.4.

Test speed | 40 | 40 | 40

Brake actuator pressure pe | | — |

Braking time | — | 2,55 | —

Brake force developed Te | | |

Brake efficiency Te/Fe | | |

Actuator stroke se | | — |

Brake input torque Ce | | — |

Brake input threshold torque C0,e | | |

2.3.1.3 Considered rolling resistance coefficient R = 0,02 (covering towed vehicles Ra and Sa specified in point 2.3.1. above with a maximum design speed not exceeding 30 km/h)

Table C

Alternative test procedure in the case of towed vehicle with vmax ≤ 30 km/h

Test type

0 | I

Appendix 1 to Annex VII of Regulation (EU) 2015/68, point: | 3.5.1.4. | 3.5.2.2. or 3.5.2.3. | 3.5.2.4.

Test speed | 30 | 30 | 30

Brake actuator pressure pe | | — |

Braking time | — | 3,90 | —

Brake force developed Te | | |

Brake efficiency Te/Fe | | |

Actuator stroke se | | — |

Brake input torque Ce | | — |

Brake input threshold torque C0,e | | |

2.3.2. In the case of vehicles of categories

‘R3a/R4a/S2a’ [Where these vehicles have been subject to the Type III test (compare point 2.3.1. or 2.3.2.+).]

‘R3b/R4b/S2b’ where the sum of the technically permissible masses per axle does not exceed 10000 kg [Where these vehicles have been subject to the Type III test (compare point 2.3.1. or 2.3.2.+).]

R3b/R4b/S2b’ where the sum of the technically permissible masses per axle exceeds 10000 kg

Test type | 0 | III

This article is long: the rest is at the official publication.