ANNEX V, Regulation (EU) 2015/504

In forcesince 7 Aug 2018

Appendix Number | Appendix title

1 | Model of the EU whole-vehicle type-approval certificate for a complete vehicle type

2 | Model of the EU whole-vehicle type-approval certificate for an incomplete type, a vehicle type with complete and incomplete variants, a vehicle type with completed and incomplete variants or a completed vehicle type

3 | Model of the addendum to the EU type-approval certificate

4 | Model of the EU type-approval certificate for a vehicle system

5 | Model of the EU type-approval certificate for a separate technical unit or component

6 | Model of the addendum to the EU type-approval certificate for a separate technical unit or component

1.1.

Model A of the EU whole-vehicle type-approval certificate for a complete vehicle type is set out in Appendix 1.

1.2.

Model B of the EU whole-vehicle type-approval certificate for an incomplete vehicle type, a vehicle type with complete and incomplete variants, a vehicle type with completed and incomplete variants or a completed vehicle type is set out in Appendix 2.

1.3.

The list of applicable requirements or acts with which the type of vehicle complies and which are appended to the EU whole-vehicle type-approval certificate when the manufacturer chooses the single-step type-approval procedure according to Article 25(6) of Regulation (EU) No 167/2013 is set out in Appendix 3.

1.4.

Model C of the EU type-approval certificate for a vehicle system is set out in Appendix 4.

1.5.

Model D of the EU type-approval certificate for a separate technical unit or component is set out in Appendix 5.

1.5.1.

The addendum to the EU type-approval certificate for a separate technical unit or component is set out in Appendix 6. When a component/separate technical unit has any restrictions on use or special mounting conditions or both, those shall be indicated in this addendum.

1.6.

The type-approval certificate shall be no bigger than A4 paper format (210 × 297 mm).

Identification of type-approval authority

Communication concerning:

EU whole-vehicle type-approval (1)

extension of EU whole-vehicle type-approval (1)

refusal of EU whole-vehicle type-approval (1)

withdrawal of EU whole-vehicle type-approval (1)

of a complete vehicle type

with regard to Regulation (EU) No 167/2013, as last amended by (Commission Delegated) (1) Regulation (EU) (No) (1) …/… (1) (5) (of the European Parliament and of the Council) (1)

EU type-approval number: …

Reason for extension/refusal/withdrawal (1): …

1.1.

Make (trade name of manufacturer): …

1.2.

Type (2): …

1.2.1

Variant(s) (2): …

1.2.2

Version(s) (2): …

1.2.3.

Commercial name(s) (if available): …

1.3.

Category, subcategory and speed index of vehicle (3): …

1.4.

Company name and address of manufacturer of the complete vehicle: …

1.4.1.

Name(s) and address(es) of assembly plants: …

1.4.2.

Name and address of manufacturer's authorised representative, if any: …

1.

Technical service responsible for carrying out the tests: …

2.

Date of test report: …

3.

Number of test report: …

The undersigned hereby certifies the accuracy of the manufacturer's description in the attached information document of the vehicle type described above, for which one or more representative samples, selected by the EU type-approval authority, have been submitted as prototypes of the vehicle type and that the attached test results apply to the vehicle type.

1.

The complete vehicle type meets/does not meet (1) all relevant requirements as listed in Annex I to Regulation (EU) No 167/2013.

1.1.

Restrictions of validity (1) (6): …

1.2.

Waivers applied (1) (7): …

1.2.1.

Reasons for the waivers (1) (7): …

1.2.2.

Alternative requirements (1) (7): …

2.

The approval is granted/extended/refused/withdrawn (1)

2.1.

The approval is granted in accordance with Article 35 of Regulation (EU) No 167/2013 and the validity of the approval is thus limited to dd/mm/yyyy (6).

Place: …

Date: …

Name and signature (or visual representation of an ‘advanced electronic signature’ according to Directive 1999/93/EC of the European Parliament and of the Council, including data for verification):

Attachments:

Information package

Test results

Name(s) and specimen(s) of the signature(s) of the person(s) authorised to sign certificates of conformity and a statement of their position in the company

A completed specimen of the certificate of conformity

–

If this model is used for type-approval of a vehicle as an exemption for new technology or new concept, pursuant to Article 35 of Regulation (EU) No 167/2013, the heading of the certificate shall read ‘EU WHOLE-VEHICLE PROVISIONAL TYPE-APPROVAL CERTIFICATE VALID ONLY ON THE TERRITORY OF … (4)’. The provisional type-approval certificate shall also specify the restrictions that have been imposed as to its validity in accordance with Article 25(4) of Regulation (EU) No 167/2013.

–

If this model is used for vehicle type-approval for a national small series, pursuant to Article 37 of Regulation (EU) No 167/2013, it shall not bear the heading ‘EU VEHICLE TYPE-APPROVAL CERTIFICATE’. The text shall specify the nature of the waivers, the reasons for them and the alternative requirements pursuant to Article 37(2) of Regulation (EU) No 167/2013.

(1)

Delete where not applicable.

(2)

Indicate the alphanumeric code Type-Variant-Version or ‘TVV’ allocated to each type, variant and version as set out in point 2.3 of Part B of Annex I to this Regulation. For the identification of variant and versions it may be employed the matrix set out in point 2.2 of Part B of Annex I to this Regulation.

(3)

Classified according to Article 4 of Regulation (EU) No 167/2013, the coding shall be indicated, e.g. ‘T4.3a’ for a low-clearance tractor with a maximum design speed below or equal to 40 km/h.

(4)

Indicate the Member State.

(5)

Indicate only the latest amendment in case of an amendment of one or more Articles of Regulation (EU) No 167/2013, according to the amendment applied for the EU type-approval.

(6)

Applicable only for type-approval of a vehicle as an exemption for new technology or new concept, pursuant to Article 35 of Regulation (EU) No 167/2013.

(7)

Applicable only for vehicle type-approval for a national small series, pursuant to Article 37 of Regulation (EU) No 167/2013.

Stamp of approval authority

Communication concerning:

EU whole-vehicle type-approval (1)

extension of EU whole-vehicle type-approval (1)

refusal of EU whole-vehicle type-approval (1)

withdrawal of EU whole-vehicle type-approval (1)

of a completed vehicle type (1)

of an incomplete vehicle type (1)

of a vehicle type with complete and incomplete variants (1)

of a vehicle type with completed and incomplete variants (1)

with regard to Regulation (EU) No 167/2013, as last amended by (Commission Delegated) (1) Regulation (EU) (No) (1) …/… (1) (8) (of the European Parliament and of the Council) (1)

EU type-approval number (1): …

Reason for extension/refusal/withdrawal (1): …

1.1.

Make (trade name of manufacturer): …

1.2.

Type (2): …

1.2.1

Variant(s) (2): …

1.2.2

Version(s) (2): …

1.2.3.

Commercial name(s) (if available): …

1.3.

Category, subcategory and speed index of vehicle (3): …

1.4.

Company name and address of the manufacturer of the base vehicle (1) (4): …

Company name and address of the manufacturer of the complete variant (1) (4): …

Company name and address of the manufacturer of the completed vehicle/variant (1) (4): …

Company name and address of the manufacturer of the latest built stage of the incomplete vehicle (1) (4): …

Company name(s) and address(es) of the manufacturer(s) of all previous stage(s) (1) (4): …

1.4.1.

Name(s) and address(es) of assembly plant(s): …

1.4.2.

Name and address of the manufacturer's representative (if any): …

1.

Technical service responsible for carrying out the tests: …

2.

Date of test report: …

3.

Number of test report: …

The undersigned hereby certifies the accuracy of the manufacturer's description in the attached information document of the vehicle type described above, for which one or more representative samples, selected by the EU type-approval authority, have been submitted as prototypes of the vehicle type and that the attached test results apply to the vehicle type.

1.1.

The complete variants of the vehicle type meet/do not meet (1) all relevant requirements as listed in Annex I to Regulation (EU) No 167/2013.

2.1.

The completed vehicle type/completed variant of the vehicle type meets/does not meet (1) all relevant requirements as listed in Annex I to Regulation (EU) No 167/2013 (4):

2.1.1.

The approval authority has verified that the completed vehicle/variant of the vehicle type meets all applicable technical requirements at the time of granting this type-approval (cf. Article 20(6) of Regulation (EU) No 167/2013).

3.1.

The incomplete vehicle type/incomplete variants of the vehicle type meets/does not meet (1) the technical requirements of the regulatory acts listed in the table in point 2 of section 2 (4).

4.1.

The approval is granted in accordance with Article 35 of Regulation (EU) No 167/2013 and its validity is thus limited to dd/mm/yyyy (6).

5.

Restrictions of validity (1) (6): …

6.

Waivers applied (1) (7): …

6.1.

Reasons for the waivers (1) (7): …

6.2.

Alternative requirements (1) (7): …

Place: …

Date: …

Name and signature (or visual representation of an ‘advanced electronic signature’ according to Directive 1999/93/EC of the European Parliament and of the Council, including data for verification): …

Attachments:

Information package

Test results

Name(s) and specimen(s) of the signature(s) of the person(s) authorised to sign certificates of conformity and a statement of their position in the company

A completed specimen of the certificate of conformity

–

If this model is used for type-approval of a vehicle as an exemption for new technology or new concept, pursuant to Article 35 of Regulation (EU) No 167/2013, the heading of the certificate shall read ‘EU WHOLE-VEHICLE PROVISIONAL TYPE-APPROVAL CERTIFICATE VALID ONLY ON THE TERRITORY OF … (5)’. The provisional type-approval certificate shall also specify the restrictions that have been imposed as to its validity in accordance with Article 25(4) of Regulation (EU) No 167/2013.

–

If this model is used for vehicle type-approval for a national small series, pursuant to Article 37 of Regulation (EU) No 167/2013, it shall not bear the heading ‘EU VEHICLE TYPE-APPROVAL CERTIFICATE’. The text shall specify the nature of the waivers, the reasons for them and the alternative requirements pursuant to Article 37(2) of Regulation (EU) No 167/2013.

This EU type-approval concerns incomplete and completed vehicles, variants or versions.

1.

Previous stage(s) approval(s) for the vehicles.

Stage | EU type-approval number | Dated | Applicable to (as appropriate) | Variants and versions which are complete or completed (as appropriate) (9)

1

(base vehicle)

2 | | | |

2.

List of requirements applicable to the approved incomplete vehicle type, variant, taking account of the scope and latest amendment to each of the regulatory acts listed below (10).

Item | Subject | Regulatory act reference | As amended by and/or stage of implementation | Applicable to variants

(1)

Delete where not applicable.

(2)

Indicate the alphanumeric code Type-Variant-Version or ‘TVV’ allocated to each type, variant and version as set out in point 2.3 of Part B of Annex I to this Regulation. For the identification of variant and versions it may be employed the matrix set out in point 2.2 of Part B of Annex I to this Regulation.

(3)

Classified according to Article 4 of Regulation (EU) No 167/2013, the coding shall be indicated, e.g. ‘T4.3a’ for a low-clearance tractor with a maximum design speed below or equal to 40 km/h.

(4)

See section 2.

(5)

Indicate the Member State.

(6)

Applicable only for type-approval of a vehicle as an exemption for new technology or new concept, pursuant to Article 35 of Regulation (EU) No 167/2013

(7)

Applicable only for vehicle type-approval for a national small series, pursuant to Article 37 of Regulation (EU) No 167/2013

(8)

Indicate only the latest amendment in case of an amendment of one or more Articles of Regulation (EU) No 167/2013, according to the amendment applied for the EU type-approval.

(9)

In the case where the approval includes one or more incomplete variants or versions (as appropriate), list those variants or versions (as appropriate) which are complete or completed.

(10)

List only subjects referred to in Annex I to Regulation (EU) No 167/2013 whose approvals have been granted in accordance with Regulation (EU) 2016/1628 or the UNECE regulations referred to in Article 49 of Regulation (EU) No 167/2013 (UNECE approvals), or are based on complete test reports issued on the basis of the OECD standard Codes as an alternative to the test reports drawn up under Regulation (EU) No 167/2013 and the delegated and implementing acts adopted pursuant to that Regulation.

Item | Subject | Regulatory act reference | As amended by and/or stage of implementation | Applicable to version

VEHICLE FUNCTIONAL SAFETY REQUIREMENTS

1 | Vehicle structure integrity | Commission Delegated Regulation (EU) 2015/208 Annex II | |

2 | Maximum design speed, speed governors and speed limitation devices | Commission Delegated Regulation (EU) 2015/208 Annex III | |

3 | Steering for fast tractors | Commission Delegated Regulation (EU) 2015/208 Annex IV | |

4 | Steering | Commission Delegated Regulation (EU) 2015/208 Annex V | |

5 | Speedometers | Commission Delegated Regulation (EU) 2015/208 Annex VI | |

6 | Field of vision and windscreen wipers | Commission Delegated Regulation (EU) 2015/208 Annex VII | |

7 | Glazing | Commission Delegated Regulation (EU) 2015/208 Annex VIII | |

8 | Rear-view mirrors | Commission Delegated Regulation (EU) 2015/208 Annex IX | |

9 | Driver information systems | Commission Delegated Regulation (EU) 2015/208 Annex X | |

10 | Lighting, light signalling devices and their light sources | Commission Delegated Regulation (EU) 2015/208 Annex XI | |

11 | Lighting installation | Commission Delegated Regulation (EU) 2015/208 Annex XII | |

12 | Vehicle occupant protection, including interior fittings, head restraints, seat belts, vehicle doors | Commission Delegated Regulation (EU) 2015/208 Annex XIII | |

13 | Vehicle exterior and accessories | Commission Delegated Regulation (EU) 2015/208 Annex XIV | |

14 | Electro-magnetic compatibility | Commission Delegated Regulation (EU) 2015/208 Annex XV | |

15 | Audible warning devices | Commission Delegated Regulation (EU) 2015/208 Annex XVI | |

16 | Heating systems | Commission Delegated Regulation (EU) 2015/208 Annex XVII | |

17 | Devices to prevent unauthorised use | Commission Delegated Regulation (EU) 2015/208 Annex XVIII | |

18 | Registration plates | Commission Delegated Regulation (EU) 2015/208 Annex XIX | |

19 | Statutory plates and markings | Commission Delegated Regulation (EU) 2015/208 Annex XX | |

20 | Dimensions and trailer masses | Commission Delegated Regulation (EU) 2015/208 Annex XXI | |

21 | Maximum laden mass | Commission Delegated Regulation (EU) 2015/208 Annex XXII | |

22 | Ballast masses | Commission Delegated Regulation (EU) 2015/208 Annex XXIII | |

23 | Safety of electrical systems | Commission Delegated Regulation (EU) 2015/208 Annex XXIV | |

24 | Fuel tanks | Commission Delegated Regulation (EU) 2015/208 Annex XXV | |

25 | Rear protective structures | Commission Delegated Regulation (EU) 2015/208 Annex XXVI | |

26 | Lateral protection | Commission Delegated Regulation (EU) 2015/208 Annex XXVII | |

27 | Load platforms | Commission Delegated Regulation (EU) 2015/208 Annex XXVIII | |

28 | Towing devices | Commission Delegated Regulation (EU) 2015/208 Annex XXIX | |

29 | Tyres | Commission Delegated Regulation (EU) 2015/208 Annex XXX | |

30 | Spray-suppression systems | Commission Delegated Regulation (EU) 2015/208 Annex XXXI | |

31 | Reverse gear | Commission Delegated Regulation (EU) 2015/208 Annex XXXII | |

32 | Tracks | Commission Delegated Regulation (EU) 2015/208 Annex XXXIII | |

33 | Mechanical couplings | Commission Delegated Regulation (EU) 2015/208 Annex XXXIV | |

VEHICLE BRAKING REQUIREMENTS

34 | Construction and fitting of braking devices and trailer braking couplings | Commission Delegated Regulation (EU) 2015/68 Annex I | |

35 | Testing and performance of braking systems and trailer braking couplings and of vehicles fitted with them | Commission Delegated Regulation (EU) 2015/68 Annex II | |

36 | Measurement of the response time | Commission Delegated Regulation (EU) 2015/68 Annex III | |

37 | Energy sources and energy storage devices of braking systems and trailer braking couplings and to vehicles fitted with them | Commission Delegated Regulation (EU) 2015/68 Annex IV | |

38 | Spring brakes and vehicles fitted with them | Commission Delegated Regulation (EU) 2015/68 Annex V | |

39 | Parking braking systems equipped with a mechanical brake-cylinder locking device | Commission Delegated Regulation (EU) 2015/68 Annex VI | |

40 | Alternative test requirements for vehicles for which Type-I, Type-II or Type-III tests are not mandatory | Commission Delegated Regulation (EU) 2015/68 Annex VII | |

41 | Testing of inertia braking systems, braking devices and trailer braking couplings and of vehicles fitted with them as regards braking | Commission Delegated Regulation (EU) 2015/68 Annex VIII | |

42 | Vehicles with hydrostatic drive and their braking devices and braking systems | Commission Delegated Regulation (EU) 2015/68 Annex IX | |

43 | Safety aspects of complex electronic vehicle control systems | Commission Delegated Regulation (EU) 2015/68 Annex X | |

44 | Test procedures applying to anti-lock braking systems and to vehicles fitted with them | Commission Delegated Regulation (EU) 2015/68 Annex XI | |

45 | EBS of vehicles with compressed-air braking systems or of vehicles with data communication via pin 6 and 7 of ISO 7638 connector and to vehicles fitted with such EBS | Commission Delegated Regulation (EU) 2015/68 Annex XII | |

46 | Hydraulic connections of the single-line type and to vehicles fitted with them | Commission Delegated Regulation (EU) 2015/68 Annex XIII | |

VEHICLE CONSTRUCTION AND GENERAL TYPE-APPROVAL REQUIREMENTS

47 | Arrangements with regard to type-approval procedures, including the requirements relating to virtual testing | Commission Delegated Regulation (EU) No 1322/2014 Annex III | |

48 | Arrangements with regard to conformity of production | Commission Delegated Regulation (EU) No 1322/2014 Annex IV | |

49 | Access to repair and maintenance information | Commission Delegated Regulation (EU) No 1322/2014 Annex V | |

50 | Roll-over protection structures (dynamic testing) | Commission Delegated Regulation (EU) No 1322/2014 Annex VI | |

51 | Roll-over protection structures (track-laying tractors) | Commission Delegated Regulation (EU) No 1322/2014 Annex VII | |

52 | Roll-over protection structures (static testing) | Commission Delegated Regulation (EU) No 1322/2014 Annex VIII | |

53 | Roll-over protection structures (front mounted roll-over protective structures on narrow-track tractors) | Commission Delegated Regulation (EU) No 1322/2014 Annex IX | |

54 | Roll-over protection structures (rear mounted roll-over protective structures on narrow-track tractors) | Commission Delegated Regulation (EU) No 1322/2014 Annex X | |

55 | Falling objects protection structures | Commission Delegated Regulation (EU) No 1322/2014 Annex XI | |

56 | Passenger seats | Commission Delegated Regulation (EU) No 1322/2014 Annex XII | |

57 | Driver's exposure to noise level | Commission Delegated Regulation (EU) No 1322/2014 Annex XIII | |

58 | Driving seat | Commission Delegated Regulation (EU) No 1322/2014 Annex XIV | |

59 | Operating space and to access to the driving position | Commission Delegated Regulation (EU) No 1322/2014 Annex XV | |

60 | Power take-offs | Commission Delegated Regulation (EU) No 1322/2014 Annex XVI | |

61 | Protection of drive components | Commission Delegated Regulation (EU) No 1322/2014 Annex XVII | |

62 | Seat-belt anchorages | Commission Delegated Regulation (EU) No 1322/2014 Annex XVIII | |

63 | Safety belts | Commission Delegated Regulation (EU) No 1322/2014 Annex XIX | |

64 | Protection against penetrating objects | Commission Delegated Regulation (EU) No 1322/2014 Annex XX | |

65 | Exhaust system | Commission Delegated Regulation (EU) No 1322/2014 Annex XXI | |

66 | Operator's manual | Commission Delegated Regulation (EU) No 1322/2014 Annex XXII | |

67 | Control devices, including safety and reliability of control systems and emergency and automatic stop devices | Commission Delegated Regulation (EU) No 1322/2014 Annex XXIII | |

68 | Protection against other mechanical hazards | Commission Delegated Regulation (EU) No 1322/2014 Annex XXIV | |

69 | Guards and protective devices | Commission Delegated Regulation (EU) No 1322/2014 Annex XXV | |

70 | Information warnings and markings | Commission Delegated Regulation (EU) No 1322/2014 Annex XXVI | |

71 | Materials and products | Commission Delegated Regulation (EU) No 1322/2014 Annex XXVII | |

72 | Batteries | Commission Delegated Regulation (EU) No 1322/2014 Annex XXVIII | |

73 | Protection against hazardous substances | Commission Delegated Regulation (EU) No 1322/2014 Annex XXIX | |

74 | Performance standards and assessment of technical services | Commission Delegated Regulation (EU) No 1322/2014 Annex XXX | |

ENVIRONMENTAL AND PROPULSION UNIT PERFORMANCE REQUIREMENTS

75 | EU type-approval of a type of engine or engine family for an agricultural and forestry vehicle type as a component / separate technical unit regarding the pollutants emitted | Commission Delegated Regulation (EU) 2018/985 Annex I | |

76 | EU type-approval of an agricultural and forestry vehicle type equipped with an engine type or engine family regarding the pollutants emitted | Commission Delegated Regulation (EU) 2018/985 Annex I | |

77 | External sound emission | Commission Delegated Regulation (EU) 2018/985 Annex III | |

Stamp of approval authority

Communication concerning:

EU type-approval (1)

extension of EU type-approval (1)

refusal of EU type-approval (1)

withdrawal of EU type-approval (1)

of a type of system/a type of a vehicle with regard to a system (1) (0)

with regard to Annex(es) (7) … to Commission Delegated Regulation(s) (EU) (No) (1) …/…, (and Annex(es) … (7) to Commission Delegated Regulation (EU) (No) (1) …/…) (1) as last amended by (Commission Delegated) (1) Regulation (EU) (No) (1) …/… (1) (6) (of the European Parliament and of the Council) (1)

EU type-approval number (1): …

Reason for extension/refusal/withdrawal (1): …

2.1.

Make(s) (trade name(s) of manufacturer): …

2.2.

Type (11): …

2.2.1.

This article is long: the rest is at the official publication.