ANNEX II, Regulation (EU) 2015/504

In forcesince 7 Aug 2018cited 1×

1.

The vehicle manufacturer shall provide, in accordance with Article 53(8) of Regulation (EU) No 167/2013, the certificates providing proof of compliance to the type-approval authority on access to vehicle OBD and vehicle repair and maintenance information which shall take the form set out in point 2.

1.1

The certificate must have a reference number supplied by the manufacturer.

2.

Manufacturer's certificate on access to vehicle OBD and vehicle repair and maintenance information and its addenda.

2.1.

Template of manufacturer's certificate on access to vehicle OBD and vehicle repair and maintenance information.

A duly completed version of this certificate shall be included in the information folder.

Reference number: …

The undersigned: [ … (full name and position)]

Company name and address of the manufacturer: …

Name and address of the manufacturer's representative (if any) (1): …

Hereby certifies that:

it provides access to vehicle OBD and vehicle repair and maintenance information in compliance with:

Chapter XV of Regulation (EU) No 167/2013

Annex V to Commission Delegated Regulation (EU) No 1322/2014

with respect to the types of vehicle, system, component and/or separate technical unit listed in the Addendum 1 to this certificate (4).

The following exceptions apply (1):

small volume manufacturers (1)

use of proprietary hardware for reprograming of control units (1)

The principal website address (5), through which the relevant information may be accessed and which are hereby certified to be in compliance with the above provisions, are listed in the Addendum 2 to this certificate. The contact details of the responsible manufacturer's representative whose signature is below are laid down in the Addendum 3 to this certificate.

Where applicable: The manufacturer hereby also certifies that it has complied with the obligation in Article 53(8) of Regulation (EU) No 167/2013 to provide the relevant information for previous approvals of these vehicle types no later than six months after the date of type-approval.

Place: …

Date: …

Signature: …

Name and position in the company: …

Addenda:

1List of the types of vehicle, system, component and separate technical unit

2Web sites addresses (5)

3Contact details

4In case of multi-stage type-approval, certificates on access to vehicle OBD and vehicle repair and maintenance information, including its addenda, corresponding to the previous stages

2.1.1.

Template of Addendum 1 to the manufacturer's certificate on access to vehicle OBD and repair and maintenance information.

List of the type(s) of vehicle (5):

1.2.

Type (2): …

1.2.1.

Variant(s) (2): …

1.2.2.

Version(s) (2): …

1.2.3

Commercial name(s) (if available): …

1.3.

Category, subcategory and speed index of the vehicle (3): …

EU type-approval number including extension number (if available): …

EU type-approval issued on (date, if available): …

List of the type(s) of system(s), component(s) and/or separate technical unit(s) (5):

2.1.

Make(s) (trade name(s) of manufacturer): …

2.2.

Type(s) (4): …

2.2.1.

Commercial name(s) (if available): …

2.2.2.

EU type-approval number(s) (if available): …

2.2.3.

EU type-approval(s) issued on (date, if available): …

2.3.

Company name(s) and address of the manufacturer(s): …

Additional information on the engine (4):

2.5.2.

Manufacturer's type coding (as marked on the engine or other means of identification): …

2.1.2.

Template of Addendum 2 to the manufacturer's certificate on access to vehicle OBD and repair and maintenance information.

Web site address (5) referred to in this certificate:

…

…

…

2.1.3.

Template of Addendum 3 to the manufacturer's certificate on access to vehicle OBD and repair and maintenance information.

Contact details of the manufacturer's representative referred to in this certificate:

…

…

…

(1)

Delete if not applicable.

(2)

Indicate the alphanumeric code Type-Variant-Version or ‘TVV’ allocated to each type, variant and version as set out in point 2.3 of Part B of Annex I to this Regulation. For the identification of variant and versions it may be employed the matrix set out in point 2.2 of Part B of Annex I to this Regulation.

(3)

Classified according to Article 4 of Regulation (EU) No 167/2013, the coding shall be indicated, e.g. ‘T4.3a’ for a low-clearance tractor with a maximum design speed below or equal to 40 km/h.

(4)

For engines, indicate the engine type designation or, in case of engine types within an engine family, the Family Type (FT) in accordance with point 4 of Part B of Annex I to Commission Implementing Regulation (EU) 2017/656.

(5)

In case of multi-stage type-approval indicate the website address of the manufacturer(s) responsible for the previous stage(s).