Annexes I, III, VIII and IX to Directive 2007/46/EC are amended as follows:
Annex I is amended as follows:
the following points 0.2.2.1. to 0.2.3.9. are inserted:
‘0.2.2.1.
Allowed Parameter Values for multistage type approval to use the base vehicle emission values (insert range if applicable) (y):
Final Vehicle mass in running order (in kg): …
Frontal area for final vehicle (in cm2): …
Rolling resistance (kg/t): …
Cross-sectional area of air entrance of the front grille (in cm2): …
0.2.3.
Identifiers (y):
0.2.3.1.
interpolation family's identifier: …
0.2.3.2.
ATCT family's identifier: …
0.2.3.3.
PEMS family's identifier: …
0.2.3.4.
Roadload family's identifier
0.2.3.4.1.
Roadload family of VH: …
0.2.3.4.2.
Roadload family of VL: …
0.2.3.4.3.
Roadload families applicable in the interpolation family: …
0.2.3.5.
Roadload Matrix family's identifier: …
0.2.3.6.
Periodic regeneration family's identifier: …
0.2.3.7.
Evaporative test family's identifier: …
0.2.3.8.
OBD family's identifier: …
0.2.3.9.
other family's identifier: …’;
the following point 2.6.3. is inserted:
‘2.6.3. Rotational mass (y): 3 % of the sum of mass in running order and 25 kg or value, per axle (kg): …’;
point 3.2.2.1. is replaced by the following:
‘3.2.2.1. Diesel/Petrol/LPG/NG or Biomethane/Ethanol (E 85)/Biodiesel/Hydrogen (1) (6)’;
the following point 3.2.12.0. is inserted:
‘3.2.12.0. Emission character of type approval (y)’;
point 3.2.12.2.5.5. is replaced by the following:
‘3.2.12.2.5.5. Schematic drawing of the fuel tank (petrol and ethanol engines only): …’;
after point 3.2.12.2.5.5. the following points are inserted:
‘3.2.12.2.5.5.1.
Fuel tank system capacity, material and construction: …
3.2.12.2.5.5.2.
Description of vapour hose material, fuel line material and connection technique of the fuel system: …
3.2.12.2.5.5.3.
Sealed tank system: yes/no
3.2.12.2.5.5.4.
Description of fuel tank relief valve setting (air ingestion and relief): …
3.2.12.2.5.5.5.
Description of the purge control system: …’;
the following point 3.2.12.2.5.7. is inserted:
‘3.2.12.2.5.7. Permeability factor: …’;
the following point 3.2.12.2.5.12. is inserted:
‘3.2.12.2.12. Water injection: yes/no (1)’;
point 3.2.19.4.1. is deleted;
point 3.2.20. is replaced by the following:
‘3.2.20. Heat storage information (y)’;
point 3.2.20.1. is replaced by the following:
‘3.2.20.1. Active heat storage device: yes/no (1)’;
point 3.2.20.2. is replaced by the following:
‘3.2.20.2. Insulation materials: yes/no (1)’;
the following points 3.2.20.2.5. to 3.2.20.2.6. are inserted:
‘3.2.20.2.5.
Worst case approach vehicle cool down: yes/no (1)
3.2.20.2.5.1.
(not worst case approach) Minimum soaking time, tsoak_ATCT (hours): …
3.2.20.2.5.2.
(not worst case approach) Location of the engine temperature measurement: …
3.2.20.2.6.
Single interpolation family within the ATCT family approach: yes/no (1)’;
points 3.5.7.1. and 3.5.7.1.1. are replaced by the following:
[Representative vehicle is tested for the road load matrix family.]
Vehicle |
Vehicle Low (VL)
if existing
Vehicle High (VH) |
VM
if existing
V representative (only for road load matrix family) | Default values
Vehicle bodywork type (variant/version) | | | — | |
Road load method used (measurement or calculation by road load family) | | | — | — |
Road load information: |
Tyres make and type, if measurement | | | — | |
Tyre dimensions (front/rear), if measurement | | | — | |
Tyre rolling resistance (front/rear) (kg/t) | | | | |
Tyre pressure (front/rear) (kPa), if measurement | | | | |
Delta CD × A of vehicle L compared to vehicle H (IP_H minus IP_L) | — | | — | — |
Delta CD × A compared to road load family vehicle L (IP_H/L minus RL_L), if calculation by road load family | | | — | — |
Vehicle test mass (kg) | | | | |
Road load coefficients |
f0 (N) | | | | |
f1 (N/(km/h)) | | | | |
f2 (N/(km/h)2) | | | | |
Frontal area m2 (0,000 m2) | — | — | — | |
Cycle Energy Demand (J) | | | | |
3.5.7.1.1.
Fuel used for the Type 1 test and selected for the measurement of the net power in accordance with Annex XX to this Regulation (for LPG or NG vehicles only): …’;
points 3.5.7.1.1.1. to 3.5.7.1.3.2.3. are deleted;
point 3.5.7.2.1. to 3.5.7.2.1.2.0. are replaced by the following:
‘3.5.7.2.1.
CO2 mass emission for pure ICE vehicles and NOVC-HEVs
3.5.7.2.1.0.
Minimum and maximum CO2 values within the interpolation family
3.5.7.2.1.1.
Vehicle high: … g/km
3.5.7.2.1.1.0.
Vehicle high (NEDC): … g/km
3.5.7.2.1.2.
Vehicle low (if applicable): … g/km
3.5.7.2.1.2.0.
Vehicle low (if applicable) (NEDC): … g/km
3.5.7.2.1.3.
Vehicle M (if applicable): … g/km
3.5.7.2.1.3.0.
Vehicle M (if applicable) (NEDC): … g/km’;
points 3.5.7.2.2. to 3.5.7.2.2.3.0. are replaced by the following:
‘3.5.7.2.2.
Charge-Sustaining CO2 mass emission for OVC-HEVs
3.5.7.2.2.1.
Charge Sustaining CO2 mass emission vehicle high: g/km
3.5.7.2.2.1.0.
Combined CO2 mass emission vehicle high (NEDC Condition B): g/km
3.5.7.2.2.2.
Charge Sustaining CO2 mass emission vehicle low (if applicable): g/km
3.5.7.2.2.2.0.
Combined CO2 mass emission vehicle low (if applicable) (NEDC Condition B): g/km
3.5.7.2.2.3.
Charge Sustaining CO2 mass emission vehicle M (if applicable): g/km
3.5.7.2.2.3.0.
Combined CO2 mass emission vehicle M (if applicable) (NEDC Condition B): g/km’;
points 3.5.7.2.3. to 3.5.7.2.3.3.0. are replaced with the following:
‘3.5.7.2.3.
Charge Depleting CO2 mass emission and weighted CO2 mass emission for OVC-HEVs
3.5.7.2.3.1.
Charge Depleting CO2 mass emission of Vehicle high: … g/km
3.5.7.2.3.1.0.
Charge Depleting CO2 mass emission of Vehicle high (NEDC Condition A): … g/km
3.5.7.2.3.2.
Charge Depleting CO2 mass emission of Vehicle low (if applicable): … g/km
3.5.7.2.3.2.0.
Charge Depleting CO2 mass emission of Vehicle low (if applicable) (NEDC Condition A): … g/km
3.5.7.2.3.3.
Charge Depleting CO2 mass emission of Vehicle M (if applicable): … g/km
3.5.7.2.3.3.0.
Charge Depleting CO2 mass emission of Vehicle M (if applicable) (NEDC Condition A): … g/km’;
the following point 3.5.7.2.3.4. is added:
‘3.5.7.2.3.4. Minimum and maximum weighted CO2 values within the OVC interpolation family’;
point 3.5.7.4.3. is deleted;
Point 3.5.8.3. and table are replaced by the following:
Total NEDC CO2 emissions saving (g/km) (w5)
Total WLTP CO2 emissions saving (g/km) (w5)’
Decision approving the eco-innovation (w2) | Code of the eco-innovation (w3) |
CO2 emissions of the baseline vehicle (g/km)
CO2 emissions of the eco-innovation vehicle (g/km)
CO2 emissions of the baseline vehicle under type 1 test-cycle (w4)
CO2 emissions of the eco-innovation vehicle under type 1 test-cycle
Usage factor (UF), i.e. temporal share of technology usage in normal operation conditions
CO2 emissions savings ((1 – 2) – (3 – 4)) * 5
xxxx/201x | | | | | | |
the following point 3.8.5. is inserted:
‘3.8.5. Lubricant specification: … W …’;
points 4.5.1.1. to 4.5.1.3. are deleted;
in point 4.6., at the bottom of the first column of the table, the word ‘Reverse’ is deleted;
the following points 4.6.1. to 4.6.1.7.1. are inserted:
‘4.6.1.
Gearshift (y)
4.6.1.1.
Gear 1 excluded: yes/no (1)
4.6.1.2.
n_95_high for each gear: … min– 1
4.6.1.3.
nmin_drive
4.6.1.3.1.
1st gear: … min– 1
4.6.1.3.2.
1st gear to 2nd:… min– 1
4.6.1.3.3.
2nd gear to standstill: … min– 1
4.6.1.3.4.
2nd gear: … min– 1
4.6.1.3.5.
3rd gear and beyond: … min– 1
4.6.1.4.
n_min_drive_set for acceleration/constant speed phases (n_min_drive_up): … min– 1
4.6.1.5.
n_min_drive_set for deceleration phases (nmin_drive_down):
4.6.1.6.
initial period of time
4.6.1.6.1.
t_start_phase: … s
4.6.1.6.2.
n_min_drive_start: … min– 1
4.6.1.6.3.
n_min_drive_up_start: … min– 1
4.6.1.7.
use of ASM: yes/no (1)
4.6.1.7.1.
ASM values: …’;
the following point 4.12. is added:
‘4.12. Gearbox lubricant: … W …’;
the following points 12.8. to 12.8.3.2. are inserted:
‘12.8.
Devices or systems with driver selectable modes which influence CO2 emissions and/or criteria emissions and do not have a predominant mode: yes/no (1)
12.8.1.
Charge sustaining test (if applicable) (state for each device or system)
12.8.1.1.
Best case mode: …
12.8.1.2.
Worst case mode: …
12.8.2.
Charge depleting test (if applicable) (state for each device or system)
12.8.2.1.
Best case mode: …
12.8.2.2.
Worst case mode: …
12.8.3.
Type 1 test (if applicable) (state for each device or system)
12.8.3.1.
Best case mode: …
12.8.3.2.
Worst case mode: …’;
in the Explanatory notes, the following footnote (y) is added:
‘(y) Only for the approval under Regulation (EC) No 715/2007 and its amendments.’;
Annex III is amended as follows:
the following point 0.2.2.1. is inserted:
‘0.2.2.1. Allowed Parameter Values for multistage type approval to use the base vehicle emission values (insert range if applicable) (y):
Final Vehicle mass (in kg): …
Frontal area for final vehicle (in cm2): …
Rolling resistance (kg/t): …
Cross-sectional area of air entrance of the front grille (in cm2): …’;
point 3.2.2.1. is replaced by the following:
‘3.2.2.1. Diesel/Petrol/LPG/NG or Biomethane/Ethanol (E 85)/Biodiesel/Hydrogen (1) (6)’;
the following point 3.2.12.2.8.2.2. is inserted:
‘3.2.12.2.8.2.2. Activation of the creep mode ‘disable after restart’/‘disable after fuelling‘/‘disable after parking’ (7)’;
point 3.2.12.8.8.1. is replaced by the following:
‘3.2.12.2.8.8.1. List of components on-board the vehicle of the systems ensuring the correct operation of NOx control measures’;
Annex VIII is amended as follows:
in point 2.1.1. the line:
‘Number of particles (PN) (#/km) (1)’
is replaced by the following:
‘Number of particles (PN) (#/km) (if applicable)’
in point 2.1.5. the line:
‘Number of particles (PN) (1)’
is replaced by the following:
‘Number of particles (PN) (if applicable)’
in point 3.1., in the third table, the last seven rows are replaced by the following:
‘f0 (N) | … | … | … |
f1 (N/(km/h)) | … | … | … |
f2 (N/(km/h)2) | … | … | … |
RR (kg/t) | … | … | … |
Delta Cd * A (for VL if applicable compared to VH) (m2) | … | … | … |
Test Mass (kg) | … | … | … |
Frontal area (m2) (for road load matrix family vehicles only)’ | | | |
in point 3.2., in the third table, the last seven rows are replaced by the following:
‘f0 (N) | … | | … |
f1 (N/(km/h)) | … | | … |
f2 (N/(km/h)2) | … | | … |
RR (kg/t) | … | | … |
Delta CD × A (for VL or VM compared to VH) (m2) | … | | … |
Test Mass (kg) | … | | … |
Frontal area (m2) (for road load matrix family vehicles only)’ | | | |
in point 3.3., in the third table, the last seven rows are replaced by the following:
‘f0 (N) | … | … |
f1 (N/(km/h)) | … | … |
f2 (N/(km/h)2) | … | … |
RR (kg/t) | … | … |
Delta CD × A (for VL compared to VH) (m2) | … | … |
Test Mass (kg) | … | … |
Frontal area (m2) (for road load matrix family vehicles only)’ | | |
in point 3.4. the second table is replaced by the following:
‘Variant/Version: | Variant/Version:
Fuel Consumption (Combined) (kg/100 km) | … | …
f0 (N) | … | …
f1 (N/(km/h)) | … | …
f2 (N/(km/h)2) | … | …
RR (kg/t) | … | …
Test Mass (kg) | …’ |
the title of point 3.5. is replaced by the following:
‘Output report(s) from the correlation tool in accordance with Regulation (EU) 2017/1152 and/or 2017/1153 and final NEDC values’
the following points 3.5.3. and 3.5.4. are inserted:
Final correlated NEDC values | Interpolation family identifier
VH | VL (if applicable)
CO2 mass emission (urban conditions) (g/km) | |
CO2 mass emission (extra-urban conditions) (g/km) | |
CO2 mass emission (combined) (g/km) | |
Fuel consumption (urban conditions) (l/100 km) (1) | |
Fuel consumption (extra-urban conditions) (l/100 km) (1) | |
Fuel consumption (combined) (l/100 km) (1) | |
Final correlated NEDC values | Interpolation family identifier
VH | VL (if applicable)
CO2 mass emission (weighted, combined) (g/km) | … | …
Fuel consumption (weighted, combined) (l/100 km) (g) | … | …’
Annex IX is amended as follows:
Part I is amended as follows:
in model A1 – side 1 of the certificate of conformity for complete vehicles, the following new points are inserted:
‘0.2.3.
Identifiers (if applicable) (r):
0.2.3.1.
interpolation family's identifier: …
0.2.3.2.
ATCT family's identifier: …
0.2.3.3.
PEMS family's identifier: …
0.2.3.4.
Roadload family's identifier: …
0.2.3.5.
Roadload Matrix family's identifier (if applicable): …
0.2.3.6.
Periodic regeneration family's identifier: …
0.2.3.7.
Evaporative test family's identifier: …’;
in model A2 – side 1 of the certificate of conformity for complete vehicles type-approved in small series, the following points are inserted:
‘0.2.3.
Identifiers (if applicable) (r):
0.2.3.1.
interpolation family's identifier: …
0.2.3.2.
ATCT family's identifier: …
0.2.3.3.
PEMS family's identifier: …
0.2.3.4.
Roadload family's identifier: …
0.2.3.5.
Roadload Matrix family's identifier (if applicable): …
0.2.3.6.
Periodic regeneration family's identifier: …
0.2.3.7.
Evaporative test family's identifier: …’;
in model B – side 1 of the certificate of conformity for completed vehicles, the following new points are inserted:
‘0.2.3.
Identifiers (if applicable) (r):
0.2.3.1.
interpolation family's identifier: …
0.2.3.2.
ATCT family's identifier: …
0.2.3.3.
PEMS family's identifier: …
0.2.3.4.
Roadload family's identifier: …
0.2.3.5.
Roadload Matrix family's identifier (if applicable): …
0.2.3.6.
Periodic regeneration family's identifier: …
0.2.3.7.
Evaporative test family's identifier: …’;
Side 2 of the certificate of conformity for category M1 vehicles (complete and completed vehicles) is amended as follows:
the following points 28 to 28.1.2. are inserted:
‘28.
Gearbox (type): …
28.1.
Gearbox ratios (to complete for vehicles with manual shift transmissions) (r)
1st gear | 2nd gear | 3rd gear | 4th gear | 5th gear | 6th gear | 7th gear | 8th gear | …
28.1.1.
Final drive ratio (if applicable): …
28.1.2.
Final drive ratios (to complete if and where applicable)
1st gear | 2nd gear | 3rd gear | 4th gear | 5th gear | 6th gear | 7th gear | 8th gear | …’
point 35. is replaced by the following:
‘35. Fitted tyre/wheel combination/energy efficiency class of rolling resistance coefficients (RRC) and tyre category used for CO2 determination (if applicable) (h) (r): …’;
point 47.1. is replaced by the following:
‘47.1. Parameters for emission testing of Vind (r)’;
point 47.1.2. is replaced by the following:
‘47.1.2. Frontal area, m2 (t): …’;
the following new point 47.1.2.1 is inserted:
‘47.1.2.1. Projected frontal area of air entrance of the front grille (if applicable), cm2: …’;
the following points 47.2. to 47.2.3. are inserted:
‘47.2.
Driving cycle (r)
47.2.1.
Driving Cycle class: 1/2/3a/3b
47.2.2.
Downscaling factor (fdsc): …
47.2.3.
Capped speed: yes/no’;
in point 49. in sub-point 1., the legend of the table is replaced by the following:
‘NEDC values | CO2 emissions | Fuel consumption’
Side 2 of the certificate of conformity for category M2 vehicles (complete and completed vehicles) is amended as follows:
the following points 28.1, 28.1.1. and 28.1.2. are inserted:
‘28.1.
Gearbox ratios (to complete for vehicles with manual shift transmissions) (r)
1st gear | 2nd gear | 3rd gear | 4th gear | 5th gear | 6th gear | 7th gear | 8th gear | …
28.1.1.
Final drive ratio (if applicable): …
28.1.2.
Final drive ratios (to complete if and where applicable)
1st gear | 2nd gear | 3rd gear | 4th gear | 5th gear | 6th gear | 7th gear | 8th gear | …’
point 35. is replaced by the following:
‘35. Fitted tyre/wheel combination/energy efficiency class of rolling resistance coefficients (RRC) and tyre category used for CO2 determination (if applicable) (h) (r): …’;
point 47.1. is replaced by the following:
‘47.1. Parameters for emission testing of Vind (r)’;
point 47.1.2. is replaced by the following:
‘47.1.2. Frontal area, m2 (t): …’;
the following point 47.1.2.1 is inserted:
‘47.1.2.1. Projected frontal area of air entrance of the front grille (if applicable), cm2: …’;
the following points 47.2. to 47.2.3. are inserted:
‘47.2.
Driving cycle (r)
47.2.1.
Driving Cycle class: 1/2/3a/3b
47.2.2.
Downscaling factor (fdsc): …
47.2.3.
Capped speed: yes/no’;
in point 49., in sub-point 1, the legend of the table is replaced by the following:
‘NEDC values | CO2 emissions | Fuel consumption’
Side 2 of the certificate of conformity for category N1 vehicles (complete and completed vehicles) is amended as follows:
the following points 28.1., 28.1.1. and 28.1.2. are inserted:
‘28.1.
Gearbox ratios (to complete for vehicles with manual shift transmissions) (r)
1st gear | 2nd gear | 3rd gear | 4th gear | 5th gear | 6th gear | 7th gear | 8th gear | …
28.1.1.
Final drive ratio (if applicable): …
28.1.2.
Final drive ratios (to complete if and where applicable)
1st gear | 2nd gear | 3rd gear | 4th gear | 5th gear | 6th gear | 7th gear | 8th gear | …’
point 35 is replaced by the following:
‘35. Fitted tyre/wheel combination/ energy efficiency class of rolling resistance coefficients (RRC) and tyre category used for CO2 determination (if applicable) (h) (r): …’;
point 47.1. is replaced by the following:
‘47.1. Parameters for emission testing of Vind (r)’;
point 47.1.2. is replaced by the following:
‘47.1.2. Frontal area, m2 (t): …’;
the following point 47.1.2.1 is inserted:
‘47.1.2.1. Projected frontal area of air entrance of the front grille (if applicable), cm2: …’;
the following points 47.2. to 47.2.3. are inserted:
‘47.2.
Driving cycle (r)
47.2.1.
Driving Cycle class: 1/2/3a/3b
47.2.2.
Downscaling factor (fdsc): …
47.2.3.
Capped speed: yes/no’;
in point 49, in sub-point 1, the legend of the table is replaced by the following:
‘NEDC values | CO2 emissions | Fuel consumption’
in point 49, in sub-point 1, in the table, the following row is added:
‘Verification factor (if applicable) | ‘1’ or ‘0’’
Side 2 of the certificate of conformity for category N2 vehicles (complete and completed vehicles) is amended as follows:
point 7. is replaced by the following:
‘7. Height (r): … mm’
the following points 28.1, 28.1.1. and 28.1.2. are inserted:
‘28.1.
Gearbox ratios (to complete for vehicles with manual shift transmissions) (r)
1st gear | 2nd gear | 3rd gear | 4th gear | 5th gear | 6th gear | 7th gear | 8th gear | …
28.1.1.
Final drive ratio (if applicable): …
28.1.2.
Final drive ratios (to complete if and where applicable)
1st gear | 2nd gear | 3rd gear | 4th gear | 5th gear | 6th gear | 7th gear | 8th gear | …’
point 35. is replaced by the following:
‘35. Fitted tyre/wheel combination/energy efficiency class of rolling resistance coefficients (RRC) and tyre category used for CO2 determination (if applicable) (h) (r): …’;
point 47.1. is replaced by the following:
‘47.1. Parameters for emission testing of Vind (r)’;
point 47.1.2. is replaced by the following:
‘47.1.2. Frontal area, m2 (t): …’;
the following point 47.1.2.1 is inserted:
‘47.1.2.1. Projected frontal area of air entrance of the front grille (if applicable), cm2: …’;
the following points 47.2. to 47.2.3. are inserted:
‘47.2.
Driving cycle (r)
47.2.1.
Driving Cycle class: 1/2/3a/3b
47.2.2.
Downscaling factor (fdsc): …
47.2.3.
Capped speed: yes/no’;
in point 49, in sub-point 1, the legend of the table is replaced by the following:
‘NEDC values | CO2 emissions | Fuel consumption’
in point 49, in sub-point 1, in the table, the following row is added:
‘Verification factor (if applicable) | ‘1’ or ‘0’’
Side 2 of the certificate of conformity for category N3 vehicles (complete and completed vehicles) is amended as follows:
point 7. is deleted.
Part II is amended as follows:
in model C1 – side 1 of the certificate of conformity for incomplete vehicles, the following points 0.2.3. to 0.2.3.7. are inserted:
‘0.2.3.
Identifiers (if applicable) (r):
0.2.3.1.
interpolation family's identifier: …
0.2.3.2.
ATCT family's identifier: …
0.2.3.3.
PEMS family's identifier: …
0.2.3.4.
Roadload family's identifier: …
0.2.3.5.
Roadload Matrix family's identifier (if applicable): …
0.2.3.6.
Periodic regeneration family's identifier: …
0.2.3.7.
Evaporative test family's identifier: …’;
in model C2 – side 1 of the certificate of conformity for incomplete vehicles type-approved in small series the following points 0.2.3. to 0.2.3.7. are inserted:
‘0.2.3.
Identifiers (if applicable) (r):
0.2.3.1.
interpolation family's identifier: …
0.2.3.2.
ATCT family's identifier: …
0.2.3.3.
PEMS family's identifier: …
0.2.3.4.
Roadload family's identifier:…
0.2.3.5.
Roadload Matrix family's identifier (if applicable): …
0.2.3.6.
Periodic regeneration family's identifier: …
0.2.3.7.
Evaporative test family's identifier: …’;
Side 2 of the certificate of conformity for category M1 vehicles (incomplete vehicles) is amended as follows:
the following points 28 to 28.1.2. are inserted:
‘28.
Gearbox (type): …
28.1.
Gearbox ratios (to complete for vehicles with manual shift transmissions) (r)
1st gear | 2nd gear | 3rd gear | 4th gear | 5th gear | 6th gear | 7th gear | 8th gear | …
28.1.1.
Final drive ratio (if applicable): …
28.1.2.
Final drive ratios (to complete if and where applicable)
1st gear | 2nd gear | 3rd gear | 4th gear | 5th gear | 6th gear | 7th gear | 8th gear | …’
point 35. is replaced by the following:
‘35. Fitted tyre/wheel combination/energy efficiency class of rolling resistance coefficients (RRC) and tyre category used for CO2 determination (if applicable) (h) (r): …’;
point 47.1. is replaced by the following:
‘47.1. Parameters for emission testing of Vind (r)’;
point 47.1.2. is replaced by the following:
‘47.1.2. Frontal area, m2 (t): …’;
the following new point 47.1.2.1 is inserted:
‘47.1.2.1. Projected frontal area of air entrance of the front grille (if applicable), cm2: …’;
the following points 47.2. to 47.2.3. are inserted:
‘47.2.
Driving cycle (r)
47.2.1.
Driving Cycle class: 1/2/3a/3b
47.2.2.