[The values quoted in the specifications are ‘true values’. In establishment of their limit values the terms of ISO 4259 ‘Petroleum products — Determination and application of precision data in relation to methods of test’ have been applied and in fixing a minimum value, a minimum difference of 2R above zero has been taken into account; in fixing a maximum and minimum value, the minimum difference is 4R (R = reproducibility). Notwithstanding this measure, which is necessary for technical reasons, the manufacturer of fuels should nevertheless aim at a zero value where the stipulated maximum value is 2R and at the mean value in the case of quotations of maximum and minimum limits. Should it be necessary to clarify the questions as to whether a fuel meets the requirements of the specifications, the terms of ISO 4259 should be applied.] [The range for the cetane number is not in accordance with the requirements of a minimum range of 4R. However, in the case of a dispute between fuel supplier and fuel user, the terms of ISO 4259 may be used to resolve such disputes provided replicate measurements, of sufficient number to archive the necessary precision, are made in preference to single determinations.] [Even though oxidation stability is controlled, it is likely that shelf life will be limited. Advice should be sought from the supplier as to storage conditions and life.]
Parameter | Unit | Limits | Test Method
minimum | maximum
Cetane number | | 45 | 56,0 | EN-ISO 5165
Density at 15 °C | kg/m3 | 833 | 865 | EN-ISO 3675
Distillation: | | | |
50 % point | °C | 245 | — | EN-ISO 3405
95 % point | °C | 345 | 350 | EN-ISO 3405
Final boiling point
°C | — | 370 | EN-ISO 3405
Flash point | °C | 55 | — | EN 22719
CFPP | °C | — | – 5 | EN 116
Viscosity at 40 °C | mm2/s | 2,3 | 3,3 | EN-ISO 3104
Polycyclic aromatic hydrocarbons | % m/m | 2,0 | 6,0 | IP 391
Sulphur content | mg/kg | — | 10 | ASTM D 5453
Copper corrosion | | — | class 1 | EN-ISO 2160
Conradson carbon residue (10 % DR) | % m/m | — | 0,2 | EN-ISO 10370
Ash content | % m/m | — | 0,01 | EN-ISO 6245
Total contamination | mg/kg | — | 24 | EN 12662
Water content | % m/m | — | 0,02 | EN-ISO 12937
Neutralization (strong acid) number | mg KOH/g | — | 0,10 | ASTM D 974
Oxidation stability | mg/ml | — | 0,025 | EN-ISO 12205
Lubricity (HFRR wear scar diameter at 60 °C) | μm | — | 400 | CEC F-06-A-96
Oxidation stability at 110 °C | H | 20,0 | — | EN 15751
FAME | % v/v | — | 7,0 | EN 14078
Additives, such as cetane improver as specified by the engine manufacturer, may be added to the ethanol fuel, as long as no negative side effects are known. If these conditions are satisfied, the maximum allowed amount is 10 % m/m.
[The values quoted in the specifications are ‘true values’. In establishment of their limit values the terms of ISO 4259 Petroleum products — Determination and application of precision data in relation to methods of test have been applied and in fixing a minimum value, a minimum difference of 2R above zero has been taken into account; in fixing a maximum and minimum value, the minimum difference is 4R (R = reproducibility). Notwithstanding this measure, which is necessary for technical reasons, the manufacturer of fuels shall nevertheless aim at a zero value where the stipulated maximum value is 2R and at the mean value in the case of quotations of maximum and minimum limits. Should it be necessary to clarify whether a fuel meets the requirements of the specifications, the terms of ISO 4259 shall be applied.] [Equivalent EN/ISO methods will be adopted when issued for properties listed above.] [Should it be necessary to clarify whether a fuel meets the requirements of the specifications, the terms of EN 15489 shall be applied.]
Parameter | Unit | Limits | Test method
Minimum | Maximum
Total alcohol (Ethanol incl. content on higher saturated alcohols) | % m/m | 92,4 | | EN 15721
Other higher saturated mono-alcohols (C3-C5) | % m/m | | 2,0 | EN 15721
Methanol | % m/m | | 0,3 | EN 15721
Density 15 °C | kg/m3 | 793,0 | 815,0 | EN ISO 12185
Acidity, calculated as acetic acid | % m/m | | 0,0025 | EN 15491
Appearance | | Bright and clear |
Flashpoint | °C | 10 | | EN 3679
Dry residue | mg/kg | | 15 | EN 15691
Water content | % m/m | | 6,5 |
EN 15489
EN-ISO 12937
EN15692
Aldehydes calculated as acetaldehyde | % m/m | | 0,0050 | ISO 1388-4
Esters calculated as ethylacetat | % m/m | | 0,1 | ASTM D1617
Sulphur content | mg/kg | | 10,0 |
EN 15485
EN 15486
Sulphates | mg/kg | | 4,0 | EN 15492
Particulate contamination | mg/kg | | 24 | EN 12662
Phosphorus | mg/l | | 0,20 | EN 15487
Inorganic chloride | mg/kg | | 1,0 | EN 15484 or EN 15492
Copper | mg/kg | | 0,100 | EN 15488
Electrical Conductivity | μS/cm | | 2,50 | DIN 51627-4 or prEN 15938
[The values quoted in the specifications are ‘true values’. In establishment of their limit values the terms of ISO 4259 Petroleum products — Determination and application of precision data in relation to methods of test have been applied and in fixing a minimum value, a minimum difference of 2R above zero has been taken into account; in fixing a maximum and minimum value, the minimum difference is 4R (R = reproducibility). Notwithstanding this measure, which is necessary for technical reasons, the manufacturer of fuels shall nevertheless aim at a zero value where the stipulated maximum value is 2R and at the mean value in the case of quotations of maximum and minimum limits. Should it be necessary to clarify whether a fuel meets the requirements of the specifications, the terms of ISO 4259 shall be applied.] [Equivalent EN/ISO methods will be adopted when issued for properties listed above.] [A correction factor of 0,2 for MON and RON shall be subtracted for the calculation of the final result in accordance with EN 228:2008.] [The fuel may contain oxidation inhibitors and metal deactivators normally used to stabilise refinery gasoline streams, but detergent/dispersive additives and solvent oils shall not be added.] [Ethanol meeting the specification of EN 15376 is the only oxygenate that shall be intentionally added to the reference fuel.] [The actual sulphur content of the fuel used for the Type 1 test shall be reported.] [There shall be no intentional addition of compounds containing phosphorus, iron, manganese, or lead to this reference fuel.] [The ethanol content and corresponding oxygen content may be zero for engines of category SMB at the choice of the manufacturer. In this case all testing of the engine family, or engine type where no family exists, shall be conducted using petrol with zero ethanol content.]
Parameter | Unit | Limits | Test method
Minimum | Maximum
Research octane number, RON | | 91,0 | 98,0 | EN ISO 5164:2005
Motor octane number, MON | | 83,0 | 89,0 | EN ISO 5163:2005
Density at 15 °C | kg/m3 | 743 | 756 |
EN ISO 3675
EN ISO 12185
Vapour pressure | kPa | 45,0 | 60,0 | EN ISO 13016-1 (DVPE)
Water content | | |
Max 0,05 % v/v
Appearance at – 7 °C: clear and bright
EN 12937
Distillation: | | | |
evaporated at 70 °C
% v/v | 18,0 | 46,0 | EN-ISO 3405
evaporated at 100 °C
% v/v | 46,0 | 62,0 | EN-ISO 3405
evaporated at 150 °C
% v/v | 75,0 | 94,0 | EN-ISO 3405
final boiling point
°C | 170 | 210 | EN-ISO 3405
Residue | % v/v | — | 2,0 | EN-ISO 3405
Hydrocarbon analysis: | | | |
olefins
% v/v | 3,0 | 18,0 |
EN 14517
EN 15553
aromatics
% v/v | 19,5 | 35,0 |
EN 14517
EN 15553
benzene
% v/v | — | 1,0 |
EN 12177
EN 238, EN 14517
saturates
% v/v | Report |
EN 14517
EN 15553
Carbon/hydrogen ratio | | Report |
Carbon/oxygen ratio | | Report |
Induction period | minutes | 480 | | EN-ISO 7536
Oxygen content | % m/m | 3,3 | 3,7 |
EN 1601
EN 13132
EN 14517
Existent gum | mg/ml | — | 0,04 | EN-ISO 6246
Sulphur content | mg/kg | — | 10 |
EN ISO 20846
EN ISO 20884
Copper corrosion (3h at 50 °C) | rating | — | Class 1 | EN-ISO 2160
Lead content | mg/l | — | 5 | EN 237
Phosphorus content | mg/l | — | 1,3 | ASTM D 3231
Ethanol | % v/v | 9,0 | 10,2 | EN 22854
[The values quoted in the specifications are ‘true values’. In establishment of their limit values the terms of ISO 4259 Petroleum products — Determination and application of precision data in relation to methods of test have been applied and in fixing a minimum value, a minimum difference of 2R above zero has been taken into account; in fixing a maximum and minimum value, the minimum difference is 4R (R = reproducibility). Notwithstanding this measure, which is necessary for technical reasons, the manufacturer of fuels shall nevertheless aim at a zero value where the stipulated maximum value is 2R and at the mean value in the case of quotations of maximum and minimum limits. Should it be necessary to clarify whether a fuel meets the requirements of the specifications, the terms of ISO 4259 shall be applied.] [The actual sulphur content of the fuel used for the emission tests shall be reported.] [Ethanol to meet specification of EN 15376 is the only oxygenate that shall be intentionally added to this reference fuel.] [The unleaded petrol content can be determined as 100 minus the sum of the % content of water, alcohols, MTBE and ETBE.] [There shall be no intentional addition of compounds containing phosphorus, iron, manganese, or lead to this reference fuel.]
Parameter | Unit | Limits | Test method
Minimum | Maximum
Research octane number, RON | | 95,0 | — | EN ISO 5164
Motor octane number, MON | | 85,0 | — | EN ISO 5163
Density at 15 °C | kg/m3 | Report | ISO 3675
Vapour pressure | kPa | 40,0 | 60,0 | EN ISO 13016-1 (DVPE)
Sulphur content | mg/kg | — | 10 | EN 15485 or EN 15486
Oxidation stability | Minutes | 360 | | EN ISO 7536
Existent gum content (solvent washed) | mg/100ml | — | 5 | EN-ISO 6246
Appearance
This shall be determined at ambient temperature or 15 °C whichever is higher
Clear and bright, visibly free of suspended or precipitated contaminants | Visual inspection
Ethanol and higher alcohols | % v/v | 83 | 85 |
EN 1601
EN 13132
EN 14517
E DIN 51627-3
Higher alcohols (C3-C8) | % v/v | — | 2,0 | E DIN 51627-3
Methanol | % v/v | | 1,00 | E DIN 51627-3
Petrol | % v/v | Balance | EN 228
Phosphous | mg/l | 0,20 | EN 15487
Water content | % v/v | | 0,300 | EN 15489 or EN 15692
Inorganic chloride content | mg/l | | 1 | EN 15492
pHe | | 6,5 | 9,0 | EN 15490
Copper strip corrosion (3h at 50 °C) | Rating | Class 1 | | EN ISO 2160
Acidity, (as acetic acid CH3COOH) |
% m/m
(mg/l)
|
0,0050
(40)
EN 15491
Electric Conductivity | μS/cm | 1,5 | DIN 51627-4 or prEN 15938
Carbon/hydrogen ratio | | Report |
Carbon/oxygen ration | | Report |
[Balance shall be read as follows: balance = 100 – C3 – < C3 – > C4.] [This method may not accurately determine the presence of corrosive materials if the sample contains corrosion inhibitors or other chemicals which diminish the corrosivity of the sample to the copper strip. Therefore, the addition of such compounds for the sole purpose of biasing the test method is prohibited.] [At the request of the engine manufacturer, a higher MON could be used to perform the type approval tests.]
Parameter | Unit | Fuel A | Fuel B | Test method
Composition: | | | | EN 27941
C3-content | % v/v | 30 ± 2 | 85 ± 2 |
C4-content | % v/v | Balance | Balance |
< C3, > C4 | % v/v | Maximum 2 | Maximum 2 |
Olefins | % v/v | Maximum 12 | Maximum 15 |
Evaporation residue | mg/kg | Maximum 50 | Maximum 50 | EN 15470
Water at 0 °C | | Free | Free | EN 15469
Total sulphur content including odorant | mg/kg | Maximum 10 | Maximum 10 | EN 24260, ASTM D 3246, ASTM 6667
Hydrogen sulphide | | None | None | EN ISO 8819
Copper strip corrosion (1h at 40 °C) | Rating | Class 1 | Class 1 | ISO 6251
Odour | | Characteristic | Characteristic |
Motor octane number | | Minimum 89,0 | Minimum 89,0 | EN 589 Annex B
As an alternative to the reference fuels set out in this point, the equivalent fuels in point 3.2.2 may be used
[Inerts (different from N2) + C2 + C2+.] [Value to be determined at 293,2 K (20 °C) and 101,3 kPa.] [Value to be determined at 273,2 K (0 °C) and 101,3 kPa.]
Characteristics | Units | Basis | Limits | Test method
minimum | maximum
Reference fuel GR
Composition: | | | | |
Methane | | 87 | 84 | 89 |
Ethane | | 13 | 11 | 15 |
Balance (1) | % mole | — | — | 1 | ISO 6974
Sulphur content | mg/m3 (2) | — | | 10 | ISO 6326-5
Inerts + C2+
Value to be determined at standard conditions 293,2 K (20 °C) and 101,3 kPa.
Reference fuel G23
Composition: | | | | |
Methane | | 92,5 | 91,5 | 93,5 |
Balance (1) | % mole | — | — | 1 | ISO 6974
N2 | % mole | 7,5 | 6,5 | 8,5 |
Sulphur content | mg/m3 (2) | — | — | 10 | ISO 6326-5
Inerts (different from N2) + C2+ C2+
Value to be determined at 293,2 K (20 °C) and 101,3 kPa.
Reference fuel G25
Composition: | | | | |
Methane | % mole | 86 | 84 | 88 |
Balance (1) | % mole | — | — | 1 | ISO 6974
N2 | % mole | 14 | 12 | 16 |
Sulphur content | mg/m3 (2) | — | — | 10 | ISO 6326-5
Inerts (different from N2) + C2+ C2+
Value to be determined at 293,2 K (20 °C) and 101,3 kPa.
Reference fuel G20
Composition: | | | | |
Methane | % mole | 100 | 99 | 100 | ISO 6974
Balance | % mole | — | — | 1 | ISO 6974
N2 | % mole | | | | ISO 6974
Sulphur content | mg/m3 | — | — | 10 | ISO 6326-5
Wobbe Index (net) | MJ/m3 | 48,2 | 47,2 | 49,2 |
As an alternative to the reference fuels in this point the equivalent reference fuels in point 3.2.1 may be used.
3.2.2.1.
The basis of each pipeline reference fuel (GR, G20, …) shall be gas drawn from a utility gas distribution network, blended, where necessary to meet the corresponding lambda-shift (Sλ) specification in Table 9.1, with an admixture of one or more of the following commercially [The use of calibration gas for this purpose shall not be required.] available gases:
Carbon dioxide;
Ethane;
Methane;
Nitrogen;
Propane.
3.2.2.2.
The value of Sλ of the resulting blend of pipeline gas and admixture gas shall be within the range specified in Table 9.1 for the specified reference fuel.
[The engine shall not be required to be tested on a gas blend with a Methane Number (MN) less than 70. In the case that the required range of Sλ for GR would result in an MN less than 70 the value of Sλ for GR may be adjusted as necessary until a value of MN no less than 70 is attained.]
Reference fuel | Minimum Sλ | Maximum Sλ
GR | 0,87 | 0,95
G20 | 0,97 | 1,03
G23 | 1,05 | 1,10
G25 | 1,12 | 1,20
3.2.2.3.
The engine test report for each test run shall include the following:
The admixture gas(es) chosen from the list in point 3.2.2.1;
The value of Sλ for the resulting fuel blend;
The Methane Number (MN) of the resulting fuel blend.
3.2.2.4.
The requirements of Appendices 1 and 2 shall be met in respect to determination of the properties of the pipeline and admixture gases, the determination of Sλ and MN for the resulting gas blend, and the verification that the blend was maintained during the test.
3.2.2.5.
In the case that one or more of the gas streams (pipeline gas or admixture gas(es)) contain CO2 in greater than a de minimus proportion, the calculation of specific CO2 emissions in Annex VII shall be corrected according to Appendix 3.
1.1.
For the purpose of this Appendix, where required the composition of the gas shall be determined by analysis of the gas using gas chromatography according to EN ISO 6974, or by an alternative technique that achieves at least a similar level of accuracy and repeatability.
1.2.
For the purpose of this Appendix, where required the measurement of gas flow shall be performed using a mass-based flowmeter.
2.1.
The composition of the utility gas supply shall be analysed prior to the admixture blending system.
2.2.
The flowrate of the utility gas entering the admixture blending system shall be measured.
3.1.
When an applicable certificate of analysis is available for an admixture (for example issued by the gas supplier) this may be used as the source of that admixture composition. In this case the on-site analysis of that admixture composition shall be permitted but shall not be required.
3.2.
Where an applicable certificate of analysis is not available for an admixture the composition of that admixture shall be analysed.
3.3.
The flowrate of each admixture entering the admixture blending system shall be measured.
4.1.
The analysis of the composition of the gas supplied to the engine after leaving the admixture blending system shall be permitted in addition to, or as an alternative to the analysis required by points 2.1 and 3.1, but shall not be required.
5.1.
The results of the gas analysis according to point 2.1, point 3.1 or 3.2 and, where applicable, point 4.1, combined with the mass flowrate of gas measured according to points 2.2 and 3.3, shall be used to calculate the MN according to EN16726:2015. The same set of data shall be used to calculate Sλ according to the procedure set out in Appendix 2.
6.1
The control and verification of the gas blend during the test shall be performed using either an open loop or closed loop control system.
6.2.1
In this case the gas analysis, flow measurements and calculations set out in points 1, 2, 3 and 4 shall be performed prior to the emission test.
6.2.2
The proportion of utility gas and admixture(s) shall be set to ensure that the Sλ is within the permitted range for the relevant reference fuel in Table 9.1.
6.2.3
When the relative proportions have been set they shall be maintained throughout the emission test. Adjustments to individual flow rates to maintain the relative proportions shall be permitted.
6.2.4
When the emission test has been completed the analysis of gas composition, flow measurements and calculations set out in points 2, 3, 4 and 5 shall be repeated. In order for the test to be considered valid the value of Sλ shall remain within the specified range for the respective reference fuel given in Table 9.1.
6.3.1
In this case the analysis of gas composition, flow measurements and calculations set out in points 2, 3, 4 and 5 shall be performed at intervals during the emission test. The intervals shall be chosen taking into consideration the frequency capability of the gas chromatograph and corresponding calculation system.
6.3.2
The results from the periodic measurements and calculations shall be used to adjust the relative proportions of utility gas and admixture in order to maintain the value of Sλ within the range specified in Table 9.1 for the respective reference fuel. The frequency of adjustment shall not exceed the frequency of measurement.
6.3.3
In order for the test to be considered valid the value of Sλ shall be within the range specified in Table 9.1 for the respective reference fuel for at least 90 % of the measurement points.
The λ-shift factor (Sλ) [Stoichiometric Air/Fuel ratios of automotive fuels — SAE J1829, June 1987. John B. Heywood, Internal combustion engine fundamentals, McGraw-Hill, 1988, Chapter 3.4 ‘Combustion stoichiometry’ (pp. 68 to 72).] shall be calculated by means of equation (9-1):
Sλ2
1 inert%100n m4 O*2100
(9-1)
Where:
Sλλ-shift factor;
inert %% by volume of inert gases in the fuel (i.e. N2, CO2, He, etc.);
O*2% by volume of original oxygen in the fuel;
n and mrefer to average CnHm representing the fuel hydrocarbons, i.e.:
n1 CH4%1002 C2%1003 C3%1004 C4%1005 C5%100..
1diluent%100
(9-2)
m4 CH4%1004 C2H4%1006 C2H6%100…8 C3H8%100..
1diluent%100
(9- 3)
Where:
CH4% by volume of methane in the fuel;
C2% by volume of all C2 hydrocarbons (e.g.: C2H6, C2H4, etc.) in the fuel;
C3% by volume of all C3 hydrocarbons (e.g.: C3H8, C3H6, etc.) in the fuel;
C4% by volume of all C4 hydrocarbons (e.g.: C4H10, C4H8, etc.) in the fuel;
C5% by volume of all C5 hydrocarbons (e.g.: C5H12, C5H10, etc.) in the fuel;
diluent% by volume of dilution gases in the fuel (i.e.: O2*, N2, CO2, He, etc.).
Example 1: G25: CH4 = 86 %, N2 = 14 % (by volume)
n1CH4%1002C2%100..
1diluent %100
10,861141000,860,861
m4CH4%1004C2H4%100..
1diluent %100
40,860,864
Sλ2
1inert%100nm4O*2100
2
114100144
1,16
Example 2: GR: CH4 = 87 %, C2H6 = 13 % (by vol)
n1CH4%1002C2%100..
1diluent %100
10,8720,13101001,13
1,13
m4CH4%1002C2H4%100..
1diluent %100
40,8760,1314,26
Sλ2
1inert%100nm4O*2100
2
101001,134,264
0,911
Example 3: USA: CH4 = 89 %, C2H6 = 4,5 %, C3H8 = 2,3 %, C6H14 = 0,2 %, O2 = 0,6 %, N2 = 4 %
n1CH4%1002C2%100..
1diluent %100
10,8920,04530,02340,00210,6441001,11
m4CH4%1002C2H4%1006C2H6%100..8C3H8%100
1diluent %100
40,8940,04580,023140,00210,641004,24
Sλ2
1inert%100nm4O*2100
2
141001,114,2440,6100
0,96
As an alternative to the above equation, Sλ may be calculated from the ratio of the stoichiometric air demand of pure methane to the stoichiometric air demand of the fuel blend supplied to the engine, as specified below.
Lambda-shift factor (Sλ) expresses the oxygen demand of any fuel blend in relation to oxygen demand of pure methane. Oxygen demand means the amount of oxygen to oxidise methane in a stoichiometric composition of reaction partners to products of complete combustion (i.e. carbon-dioxide and water).
For the combustion of pure methane the reaction is as set out in equation (9-4):
1 · CH4 + 2 · O2 → 1 · CO2 + 2 · H2O | (9-4)
In this case the ratio of molecules in stoichiometric composition of reaction partners is exactly 2:
nO2
nCH4
2
Where:
nO2number of molecules of oxygen
nCH4number of molecules of methane
The oxygen demand for pure methane is therefore:
nO22 ·nCH4 with a reference value of [nCH4]= 1 kmol
The value of Sλ may be determined from the ratio of the ratio of the stoichiometric composition of oxygen and methane to the ratio of the stoichiometric composition of oxygen and the fuel blend supplied to the engine, as set out in equation (9-5):
S λ
n O2
n CH4
n O2
n blend
2
n O2blend
(9-5)
Where:
nblendnumber of molecules of the fuel blend
(nO2)blendthe ratio of the molecules in the stoichiometric composition of oxygen and the fuel blend supplied to the engine
Because air contains 21 % oxygen the stoichiometric air demand Lst of any fuel shall be calculated by means of equation (9-6):
L st,fuel
n O2, fuel
0,21 | (9-6)
Where:
Lst,fuelthe stoichiometric air demand for the fuel
nO2 fuelthe stoichiometric oxygen demand for the fuel
Consequently the value of Sλ may also be determined from the ratio of the stoichiometric composition of air and methane to the ratio of the stoichiometric composition of air and the fuel blend supplied to the engine, i.e. the ratio of the stoichiometric air demand of methane to that of the fuel blend supplied to the engine, as set out in equation (9-7):
S λ
n O2
n CH4
0,21
n O2
n blend
0,21
n O2
0,21CH 4
n O2
0,21blend
L st,CH 4
L st,blend
(9-7)