Art. 1 Regulation (EU) 2024/1610

Amendments to Regulation (EU) 2019/1242

In forcesince 14 May 2024

Regulation (EU) 2019/1242 is amended as follows:

(1)

Article 1 is replaced by the following:

1.

This Regulation sets CO2 emissions performance standards for new heavy-duty vehicles. Those standards contribute to achieving the Union’s climate-neutrality objective and the intermediate Union climate targets, as laid down in Regulation (EU) 2021/1119 of the European Parliament and of the Council [Regulation (EU) 2021/1119 of the European Parliament and of the Council of 30 June 2021 establishing the framework for achieving climate neutrality and amending Regulations (EC) No 401/2009 and (EU) 2018/1999 (“European Climate Law”) (OJ L 243, 9.7.2021, p. 1], Member States’ targets of reducing their greenhouse gas emissions, as laid down in Regulation (EU) 2023/857 of the European Parliament and of the Council [Regulation (EU) 2023/857 of the European Parliament and of the Council of 19 April 2023 amending Regulation (EU) 2018/842 on binding annual greenhouse gas emission reductions by Member States from 2021 to 2030 contributing to climate action to meet commitments under the Paris Agreement, and Regulation (EU) 2018/1999 (OJ L 111, 26.4.2023, p. 1).’;], and the objectives of the Paris Agreement, as well as to ensuring the proper functioning of the internal market.

2.

This Regulation also lays down requirements for the reporting of CO2 emissions from, and fuel consumption of, new heavy-duty vehicles registered in the Union.

(2)

Article 2 is amended as follows:

(a)

paragraph 1 is replaced by the following:

‘1. This Regulation shall apply to new vehicles, which have either been type-approved or approved individually under Regulation (EU) 2018/858 or which are referred to in Article 2(3) of that Regulation, and which belong to any of the following vehicle categories:

(a)

M2 and M3;

(b)

N1, N2 and N3, provided that the vehicles do not fall under Regulation (EU) 2019/631;

(c)

O3 and O4.

For the purposes of this Regulation, the vehicles referred to in points (a), (b) and (c) of the first subparagraph shall be referred to as heavy-duty vehicles. Vehicles falling under point (a) or (b) of the first subparagraph shall be referred to as heavy-duty motor vehicles.

The vehicle categories referred to in this Regulation refer to the vehicle categories as defined in Article 4 of Regulation (EU) 2018/858 and in Annex I thereto.’

;

(b)

paragraph 2 is replaced by the following:

‘2. For the purposes of this Regulation, heavy-duty vehicles shall be considered as new heavy-duty vehicles in a given reporting period, if they are registered in the Union for the first time in that reporting period and have not been previously registered outside the Union.

A previous registration outside the Union that was made less than three months before registration in the Union shall not be taken into account.

This Regulation shall not apply to heavy-duty vehicles that are registered for the first time for a period not exceeding one month and that are registered for the sole purpose of transfer to a country outside the Union.’

;

(3)

Article 3 is amended as follows:

(a)

point (1) is replaced by the following:

‘(1) “reference CO2 emissions” means the average of the specific CO2 emissions in the reference period of all new heavy-duty vehicles in each of the vehicle sub-groups, determined in accordance with point 3 of Annex I;’

;

(b)

the following points are inserted:

‘(3a) “reporting period” means the period from 1 July of a given year to 30 June of the following year;

(3b)

“reference period” means the reporting period of a given year with respect to which the regulatory CO2 emissions reduction obligations for a certain vehicle sub-group are specified under this Regulation;’

;

(c)

point (5) is replaced by the following:

‘(5) “specific CO2 emissions target” means the CO2 emissions target of an individual manufacturer, determined annually for the preceding reporting period in accordance with point 4 of Annex I;’

;

(d)

point (9) is replaced by the following:

‘(9) “vocational vehicle” means a heavy-duty vehicle intended to be used for specific duties which, according to the information in its certificate of conformity, as reported by Member States, fulfils the criteria laid down in point 1.2 of Annex I;’

;

(e)

point (10) is replaced by the following:

‘(10) “manufacturer” means the person or body to which the vehicles registered in a given period have been attributed in accordance with Article 7a;’

;

(f)

the following point is inserted:

‘(10a) “reporter” means an entity which is responsible for the reporting of data to the Commission;’

;

(g)

point (11) is replaced by the following:

‘(11) “zero-emission heavy-duty vehicle” means any of the following vehicles:

(a)

a heavy-duty motor vehicle without an internal combustion engine, or with an internal combustion engine that emits not more than 3 g CO2/(tkm) or 1 g CO2/(pkm) as determined in accordance with Article 9 of Regulation (EU) 2017/2400;

(b)

a heavy-duty motor vehicle without an internal combustion engine, or with an internal combustion engine that emits not more than 1 g/kWh of CO2 as determined in accordance with Regulation (EC) No 595/2009 and its implementing measures or not more than 1 g/km of CO2 as determined in accordance with Regulation (EC) No 715/2007 of the European Parliament and of the Council [Regulation (EC) No 715/2007 of the European Parliament and of the Council of 20 June 2007 on type approval of motor vehicles with respect to emissions from light passenger and commercial vehicles (Euro 5 and Euro 6) and on access to vehicle repair and maintenance information (OJ L 171, 29.6.2007, p. 1).’;] and its implementing measures, provided that no CO2 emissions have been determined pursuant to Regulation (EU) 2017/2400;

(c)

a trailer equipped with a device that actively supports its propulsion, and that has no internal combustion engine or has an internal combustion engine that emits less than 1 g CO2/kWh as determined in accordance with Regulation (EC) No 595/2009 and its implementing measures or in accordance with UNECE Regulation (EC) No 49.

(h)

point (12) is replaced by the following:

‘(12) “low-emission heavy-duty vehicle” means a heavy-duty vehicle, other than a zero-emission heavy-duty vehicle, with specific CO2 emissions of less than half of the reference CO2 emissions of all vehicles in the vehicle sub-group to which the heavy-duty vehicle belongs, as determined in accordance with point 2.3.4 of Annex I;’

;

(i)

the following points are added:

‘(16) “primary vehicle” means a primary vehicle as defined in Article 3, point (22), of Regulation (EU) 2017/2400;

(17)

“primary vehicle of a heavy-duty vehicle” means a primary vehicle, for the simulation of which a generic body is allocated that corresponds to the actual body of the heavy-duty vehicle with regard to its floor (low/high) deck (single/double) configurations and any other parameters as applicable;

(18)

“completed vehicle” means a completed vehicle as defined in Article 3, point (26), of Regulation (EU) 2018/858;

(19)

“complete vehicle” means a complete vehicle as defined in Article 3, point (27), of Regulation (EU) 2018/858;

(20)

“off-road vehicle” means an off-road vehicle as defined in Part A, point 2.1, of Annex I to Regulation (EU) 2018/858;

(21)

“special purpose vehicle” means a special purpose vehicle as defined in Article 3, point (31), of Regulation (EU) 2018/858;

(22)

“off-road special purpose vehicle” means an off road special purpose vehicle as defined in Part A, point 2.3.1, of Annex I to Regulation (EU) 2018/858;

(23)

“certificate of conformity” means a certificate of conformity as defined in Article 3, point (5), of Regulation (EU) 2018/858;

(24)

“public contract”, in the context of public procurement procedures and unless otherwise specified, means a “public contract” as defined in Article 2(1), point (5), of Directive 2014/24/EU of the European Parliament and of the Council [Directive 2014/24/EU of the European Parliament and of the Council of 26 February 2014 on public procurement and repealing Directive 2004/18/EC (OJ L 94, 28.3.2014, p. 65).], “supply, works and service contracts” as defined in Article 2, point (1), of Directive 2014/25/EU of the European Parliament and of the Council [Directive 2014/25/EU of the European Parliament and of the Council of 26 February 2014 on procurement by entities operating in the water, energy, transport and postal services sectors and repealing Directive 2004/17/EC (OJ L 94, 28.3.2014, p. 243).], and “concessions” as defined in Article 5, point (1), of Directive 2014/23/EU of the European Parliament and of the Council [Directive 2014/23/EU of the European Parliament and of the Council of 26 February 2014 on the award of concession contracts (OJ L 94, 28.3.2014, p. 1).’;];

(25)

“extra heavy combination lorry” or “EHC lorry” means a heavy-duty vehicle of category N3 suitable for use in a vehicle combination and meeting all the following design and construction criteria:

(a)

having three axles or more;

(b)

with an engine rated power of at least 400 kW;

(c)

designed with a technically permissible maximum laden mass (TPMLM) of the combination of more than 60 tonnes;

(j)

the following paragraphs are added:

‘For the purposes of this Regulation, “a group of connected manufacturers” means a manufacturer and its connected undertakings.

In relation to a manufacturer, “connected undertakings” means:

(a)

undertakings in which the manufacturer has, directly or indirectly:

(i)

the power to exercise more than half the voting rights;

(ii)

the power to appoint more than half the members of the supervisory board, board of management or bodies legally representing the undertaking; or

(iii)

the right to manage the undertaking’s affairs;

(b)

undertakings which directly or indirectly have, over the manufacturer, the right or powers referred to in point (a);

(c)

undertakings in which an undertaking referred to in point (b) has, directly or indirectly, the right or powers referred to in point (a);

(d)

undertakings in which the manufacturer together with one or more of the undertakings referred to in point (a), (b) or (c), or in which two or more of the latter undertakings, jointly have the right or powers referred to in point (a);

(e)

undertakings in which the right or the powers referred to in point (a) are jointly held by the manufacturer or one or more of its connected undertakings referred to in points (a) to (d) and one or more third parties.’

;

(4)

the following articles are inserted:

1.

The average CO2 emissions of the Union fleet of new heavy-duty motor vehicles, other than special purpose vehicles, off-road vehicles and off-road special purpose vehicles shall be reduced by the following percentages compared to the average CO2 emissions of the reporting period of the year 2019:

(a)

15 % for vehicle sub-groups 4-UD, 4-RD, 4-LH, 5-RD, 5-LH, 9-RD, 9-LH, 10-RD and 10-LH for the reporting periods of the years 2025 to 2029;

(b)

45 % for all vehicle sub-groups other than vocational vehicles for the reporting periods of the years 2030 to 2034;

(c)

65 % for all vehicle sub-groups for the reporting periods of the years 2035 to 2039;

(d)

90 % for all vehicle sub-groups for the reporting periods of the year 2040 onwards.

2.

The vehicle sub-groups shall contribute to the CO2 emissions reduction targets referred to in paragraph 1, in accordance with point 4.3 of Annex I.

3.

The CO2 emissions related to the Union fleet of new trailers shall be reduced in accordance with point 4.3 of Annex I.

4.

Notwithstanding Article 2(3) of Regulation (EU) 2017/2400, approved heavy-duty vehicles falling under Article 2(3), first subparagraph, point (b), of Regulation (EU) 2018/858 shall not be subject to the CO2 emissions reduction targets set out in paragraphs 1 to 3 of this Article, unless the manufacturer chooses to include those heavy-duty vehicles in the calculation of its specific CO2 emissions and targets when reporting those heavy-duty vehicles in accordance with Part B of Annex IV to this Regulation.

5.

Heavy-duty vehicles other than those referred to in paragraph 4 that are registered for use by civil protection services, fire services, forces responsible for maintaining the public order or urgent medical care services shall not be subject to the CO2 emissions reduction targets set out in paragraphs 1 to 3, provided that a Member State so indicates in the registration and reporting process, thereby confirming in the data reported in accordance with Part A of Annex IV that the purpose of the heavy-duty vehicle cannot be equally served by a zero-emission heavy-duty vehicle and it is therefore in the public interest to register a heavy-duty vehicle with a combustion engine to fulfil that purpose.

Heavy-duty vehicles registered for use by armed services shall not be subject to the requirements of this Regulation if a Member State decides not to report them in accordance with Part A of Annex IV.

By 30 June 2025, the Commission shall submit to the European Parliament and to the Council a report which considers the need to facilitate the uptake on the Union market of heavy-duty vehicles which are retrofitted to become zero-emission heavy-duty vehicles, including by way of harmonised rules. That report shall contain an analysis of the options and the impact of those options. Where appropriate, the analysis shall be accompanied by a legislative initiative or other action.

By 30 June 2027, the Commission shall submit to the European Parliament and to the Council a report which contains an analysis of the potential need for and impact of initiatives to increase the share of zero-emission heavy-duty motor vehicles owned or leased by large fleet operators. In that report, the Commission shall consider possible options to increase the deployment of zero-emission heavy-duty vehicles owned or leased by large fleet operators.

1.

For heavy-duty vehicles referred to in the fourth column of the table in point 4.2 of Annex I (“urban buses”), manufacturers shall comply with the 90 % and 100 % minimum shares of zero-emission heavy-duty vehicles in their fleet of new heavy-duty vehicles in accordance with point 4.3.2 of Annex I.

2.

The Commission shall specify, by means of implementing acts, the common technical specifications, including standards, regarding the technical and open interoperability between the recharging and refuelling infrastructure and urban buses, in terms of physical connections and communication exchange.

Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 16(2).

3.

The Commission is empowered to adopt delegated acts in accordance with Article 17 to supplement this Regulation by laying down common technical specifications, including standards, regarding the safe and secure sharing and use of the data generated in relation to the use of urban buses.

1.

Contracting authorities and contracting entities shall base the award of public supply contracts for the purchase, lease, rent or hire-purchase of new zero-emission urban buses, as well as of public service contracts having as their main subject matter the use of such urban buses, on the most economically advantageous tender which shall include the best price-quality ratio.

2.

Contracting authorities and contracting entities shall use at least two of the following criteria as technical specifications or as award criteria, at least one of which shall relate to the tender’s contribution to the security of supply as set out in points (a) to (d), depending on the market situation and in compliance with Directive 2014/23/EU, 2014/24/EU or 2014/25/EU, and applicable sectoral legislation, as well as with the Union’s international commitments, including the World Trade Organization Agreement on Government Procurement (the “GPA”) and other international agreements by which the Union is bound:

(a)

the proportion of the products of tenders originating in third countries, as determined in accordance with Regulation (EU) No 952/2013 of the European Parliament and of the Council [Regulation (EU) No 952/2013 of the European Parliament and of the Council of 9 October 2013 laying down the Union Customs Code (OJ L 269, 10.10.2013, p. 1).’;]; that criterion shall only apply to products of tenders originating in countries that are not parties to the GPA and that have not concluded a free trade agreement, including rules on public procurement, with the Union;

(b)

the current and estimated availability of essential spare parts for the functioning of the equipment that is the subject of the tender;

(c)

a commitment by the tenderer that possible changes in its supply chain during the execution of the contract will not adversely affect the execution of the contract;

(d)

certification or documentation demonstrating that the organisation of the tenderer’s supply chain allows it to comply with the security of supply requirement;

(e)

environmental sustainability going beyond the minimum requirements provided for in applicable Union legal acts.

The first subparagraph shall not preclude contracting authorities and contracting entities from using additional criteria.

3.

If the tender’s contribution to security of supply is used as an award criterion, it shall be given a weighting of between 15 to 40 % of the award criteria.

(5)

in Article 4, the first paragraph is replaced by the following:

‘Starting from 1 July 2020, and in each subsequent reporting period, the Commission shall determine for each manufacturer the average specific CO2 emissions in g/tkm for the preceding reporting period, by taking the following into account:

(a)

the data reported for the manufacturer’s new heavy-duty vehicles registered in the preceding reporting period;

(b)

the zero- and low-emission factor determined in accordance with Article 5; and

(c)

in the reporting periods of the years 2030 to 2034, new zero-emission vocational vehicles falling within the scope of point 1.1.1 of Annex I.’

;

(6)

Article 5 is amended as follows:

(a)

paragraph 1 is replaced by the following:

‘1. Starting from 1 July 2020 and for each subsequent reporting period until the reporting period of the year 2029, the Commission shall determine for each manufacturer the zero- and low-emission factor for the preceding reporting period.

The zero- and low-emission factor shall take into account the number and the CO2 emissions of all zero- and low-emission heavy-duty vehicles of category N in the manufacturer’s fleet.’

;

(b)

paragraph 3 is replaced by the following:

‘3. For the reporting periods from 2025 to 2029, the zero- and low-emission factor shall be determined on the basis of a 2 % benchmark in accordance with point 2.3.2 of Annex I.’

;

(c)

paragraph 4 is replaced by the following:

‘4. The zero- and low-emission factor shall reduce the average specific CO2 emissions of a manufacturer by a maximum of 3 %. The contribution to that factor of the zero-emission heavy-duty vehicles of category N, other than those in vehicle sub-groups 4-UD, 4-RD, 4-LH, 5-RD, 5-LH, 9-RD, 9-LH, 10-RD or 10-LH, shall reduce the average specific CO2 emissions of a manufacturer by a maximum of 1,5 %.’

;

(7)

Article 6 is replaced by the following:

For the reporting period of the year 2025 and for each subsequent reporting period, the Commission shall determine for each manufacturer a specific CO2 emissions target for the preceding reporting period. That target shall be determined in accordance with point 4.1 of Annex I.’

;

(8)

the following articles are inserted:

1.

For the purpose of calculating the average specific CO2 emissions of manufacturers in accordance with Article 4 and point 2.2 of Annex I, individual heavy-duty vehicles may be transferred between manufacturers, provided the following conditions are fulfilled:

(a)

for all transfers: the request is jointly submitted by the transferring and the receiving manufacturer;

(b)

for the transfer of heavy-duty vehicles other than zero-emission heavy-duty vehicles: the transferring and the receiving manufacturer belong to a group of connected manufacturers;

(c)

for the transfer of zero-emission heavy-duty vehicles between manufacturers not belonging to a group of connected manufacturers: the number of zero-emission heavy-duty vehicles transferred to a manufacturer does not exceed 5 % of all its new heavy-duty vehicles registered in a given reporting period.

The manufacturers shall submit the transfer requests to the Commission using the electronic tools provided by the Commission.

2.

Where the Commission considers that the conditions for a transfer are fulfilled, it shall not take the transferred heavy-duty vehicle into account for the calculation of relevant values for the transferring manufacturer, but shall take it into account for the calculation of relevant values for the receiving manufacturer.

1.

If a manufacturer registers fewer than 100 new heavy-duty vehicles in a given reporting period, the average specific CO2 emissions as provided for in Article 4 and in point 2.7 of Annex I and the specific CO2 emissions targets as provided for in Article 6 and in point 4.1 of Annex I shall be set at “0” for that reporting period.

2.

Where paragraph 1 of this Article applies, the values of the average specific CO2 emissions and of the specific CO2 emissions targets shall not be included in the publication of data under Article 11 for the manufacturers and reporting periods concerned.

3.

The exemption laid down in paragraph 1 shall not apply in a given reporting period in any of the following cases:

(a)

if the manufacturer so requests;

(b)

if the manufacturer requests a transfer of heavy-duty vehicles in accordance with Article 6a;

(c)

if the manufacturer is part of a group of connected manufacturers that collectively registered more than 100 heavy-duty vehicles in that reporting period or is part of a group of connected manufacturers that includes a manufacturer to which point (a) or (b) applies.

4.

Manufacturers which are not part of a group within the meaning of paragraph 3, point (c), shall inform the Commission if they registered fewer than 100 heavy-duty vehicles in a given reporting period.

5.

Manufacturers to which the exemption laid down in paragraph 1 does not apply shall inform the Commission in each reporting period about all their connected undertakings to which the exemption applies.

6.

Manufacturers shall inform the Commission for the purposes of paragraphs 4 and 5 by using the electronic tools provided by the Commission.’

;

(9)

Article 7 is amended as follows:

(a)

in paragraph 1, first subparagraph, the introductory wording is replaced by the following:

This article is long: the rest is at the official publication.