The method of genetic sexing for Xenopus laevis is based on Yoshimoto et al., 2008. Procedures in detail on the genotyping can be obtained from this publication, if needed. Alternative methods (e.g. high-throughput qPCR) may be used if considered suitable.
Forward 5’-CCACACCCAGCTCATGTAAAG-3’
Reverse 5’-GGGCAGAGTCACATATACTG-3’
Forward 5’-AACAGGAGCCCAATTCTGAG-3’
Reverse 5’-AACTGCTTGACCTCTAATGC-3’
Purify DNA from muscle or skin tissue using e.g., Qiagen DNeasy Blood and Tissue Kit (cat # 69506) or similar product according to kit instructions. DNA can be eluted from the spin columns using less buffer to yield more concentrated samples if deemed necessary for PCR. Note that DNA is quite stable, so care should be taken to avoid cross-contamination that could lead to mischaracterisation of males as females, or vice versa.
A sample protocol using JumpStartTM Taq from Sigma is outlined in Table 1.
[Nuclease-free water]
Note: When preparing Master Mixes, prepare extra to account for any loss that may occur while pipetting (example: 25x should be used for only 24 reactions).
Master Mix | 1x (μl) | [Final]
NFW | 11 | —
10X Buffer | 2,0 | —
MgCl2 (25mM) | 2,0 | 2,5 mM
dNTP’s (10mM each) | 0,4 | 200 μM
Marker for primer (8 μM) | 0,8 | 0,3 μM
Marker rev primer (8 μM) | 0,8 | 0,3 μM
Control for primer (8 μM) | 0,8 | 0,3 μM
Control rev primer (8 μM) | 0,8 | 0,3 μM
JumpStartTM Taq | 0,4 | 0,05 units/μl
DNA template | 1,0 | ~200 pg/μl
Reaction:
Master Mix | 19,0 μl
Template | 1,0 μl
Total | 20.0 μl
Thermocycler Profile:
Step 1. | 94 oC | 1 min
Step 2. | 94 oC | 30 sec
Step 3. | 60 oC | 30 sec
Step 4. | 72 oC | 1 min
Step 5. | Go to step 2. | 35 cycles
Step 6. | 72 oC | 1 min
Step 7. | 4 oC | hold
PCR products can be run immediately in a gel or stored at 4 oC.
Tris | 24,2 g
Glacial acetic acid | 5,71 ml
Na2 (EDTA)·2H2O | 3,72 g
Add water to 100 ml
H2O | 392 ml
50X TAE | 8 ml
3 parts NuSieve™ GTG™ agarose
1 part Fisher agarose low electroendosmosis (EEO)
Prepare a 3 % gel by adding 1,2 g agarose mix to 43 ml 1X TAE. Swirl to disassociate large clumps.
Microwave agarose mixture until completely dissolved (avoid boiling over). Let cool slightly.
Add 1,0 μL ethidium bromide (10 mg/ml). Swirl flask. Note that ethidium bromide is mutagenic, so alternative chemicals should, in so far as is technically possible, be used for this step to minimise health risks to workers [In accordance to Article 4.1 of Directive 2004/37/EC of the European Parliament and of the Council of 29 April 2004 on the protection of workers from the risks related to exposure to carcinogens or mutagens at work (Sixth individual Directive within the meaning of Article 16(1) of Council Directive 89/391/EEC) (OJ L 158, 30.4.2004, p. 50).].
Pour gel into mould with comb. Cool completely.
Add gel to apparatus. Cover gel with 1X TAE.
Add 1 μl of 6x loading dye to each 10 μl PCR product.
Pipette samples into wells.
Run at 160 constant volts for ~20 minutes.
An agarose gel image showing the band patterns indicative of male and female individuals is shown in Figure 1.
Yoshimoto S, Okada E, Umemoto H, Tamura K, Uno Y, Nishida-Umehara C, Matsuda Y, Takamatsu N, Shiba T, Ito M. 2008. A W-linked DM-domain gene, DM-W, participates in primary ovary development in Xenopus laevis. Proceedings of the National Academy of Sciences of the United States of America 105: 2469-2474.