ANNEX I: DEFINITIONS, REQUIREMENTS, CONSTRUCTIONS AND FITTING, Directive (EU) 1991/422

In forcesince 22 Aug 1991

Item 1.16.3 shall read:

‘1.16.3 Centre-axle trailer

“Centre-axle trailer” means a towed vehicle equipped with a towing device which cannot move vertically (in relation to the trailer), and in which the axle(s) is (are) positioned close to the centre of gravity of the vehicle (when uniformly loaded) such that only a small static vertical load, not exceeding 10 % of that corresponding to the maximum mass of the trailer or load of 1 000 daN (whichever is the lesser) is transmitted to the drawing vehicle.’

(remainder unchanged)Item 2.1.2.3, add at the end: ‘The trailer air brake and the parking brake of the drawing vehicle may be operated simultaneously, provided that the driver is able to check, at any time, that the parking brake performance of the vehicle combination, obtained by the purely mechanical action of the parking brake device, is sufficient.’Item 2.2.1.5.2 shall read: (only English text amended)

‘2.2.1.5.2 | Furthermore, storage devices located …’

(remainder unchanged).Item 2.2.1.8 shall read:

‘2.2.1.8 | The action of the service braking device must be appropriately distributed among the axles. In the case of vehicles with more than two axles, in order to avoid wheel-locking or glazing of the brake linings, the brake force on certain axles may be reduced to zero automatically when carrying a much reduced load, provided that the vehicle meets all the performance requirements prescribed in Annex II.’

After item 2.2.1.11, the following new items 2.2.1.11.1 and 2.2.1.11.2 shall be added:

‘2.2.1.11.1 | Wear adjustment shall be automatic for the service brakes. However, the fitting of automatic adjustment devices is optional for off-road vehicles of categories N2 and N3, and for rear brakes of vehicles of categories M1 and N1. Automatic wear adjustment devices shall be such that after heating followed by cooling of the brakes, effective braking is still ensured. In particular, the vehicle shall remain capable of normal running after the tests conducted in accordance with Annex II, item 1.3 (Type I test) and Annex II, item 1.4 (Type II test).

2.2.1.11.2 | It shall be possible to easily check this wear on service brake linings, from the outside or underside of the vehicle, utilizing only the tools or equipment normally supplied with the vehicle; for instance, by the provision of appropriate inspection holes or by some other means. Alternatively, acoustical or optical devices warning the driver at his driving position when lining replacement is necessary are acceptable. The removal of front and/or rear wheels is permitted for this purpose on category M1 and N1 vehicles only.’

After item 2.2.1.12.2, the following new item 2.2.1.12.3 shall be added:

‘2.2.1.12.3 | the type of fluid to be used in the hydraulic transmission braking devices shall be identified in accordance with ISO Standard 9128-1987. The relevant symbol according to figure 1 or 2 must be affixed in a visible position in indelible form within 100 mm of the filling ports of the fluid reservoirs; additional information may be provided by the manufacturers.’

Item 2.2.1.18.3 shall read:

‘2.2.1.18.3 | in the case of a break or leak in one of the air supply pipes (or in such other type of connection as may be adopted), it must nevertheless be possible for the driver to fully or partially actuate the trailer brakes, by means either of the service braking control or of the secondary braking control or of the parking braking control, unless the break or leak automatically causes the trailer to be braked with the performance prescribed in item 2.2.3 of Annex II;’

Items 2.2.1.18.4.1 and 2.2.1.18.4.2 shall read:

‘2.2.1.18.4.1 | when the designated brake control of the controls mentioned in item 2.2.1.18.3 above is fully actuated, the pressure in the supply line must fall to 1,5 bar within the following two seconds;

2.2.1.18.4.2 | when the supply line is evacuated at the rate of at least 1 bar/s, the automatic braking of the trailer must start to operate before the pressure in the supply line falls to 2 bar.’

After item 2.2.1.23, the following new item 2.2.1.24 shall be added:

‘2.2.1.24 | In the case of a motor vehicle authorized to draw a trailer of category O3 or O4, the service braking device of the trailer may only be operated in conjunction with the service, secondary or parking braking device of the drawing vehicle.’

After item 2.2.2.8, the following new items 2.2.2.8.1 and 2.2.2.8.2 shall be added:

‘2.2.2.8.1 | Wear adjustment shall be automatic for the service brakes. However, the fitting of automatic adjustment devices is optional for vehicles of categories O1 and O2. Automatic wear adjustment devices shall be such that after heating followed by cooling of the brakes, effective braking is still ensured.

In particular, the vehicle shall remain capable of normal running after the tests conducted in accordance with Annex II, item 1.3 (Type I test) and Annex II, item 1.4 (Type II test).

2.2.2.8.2 | It shall be possible to easily check this wear on service brake linings, from the outside or underside of the vehicle, utilizing only the tools or equipment normally supplied with the vehicle; for instance, by the provision of appropriate inspection holes or by some other means.’

Item 2.2.2.9, delete the words ‘single-axled’ in the third line and substitute ‘separation’ for ‘breakage’ and ‘separates’ for ‘breaks’ in this item.

Item 2.2.2.11 shall read:

‘2.2.2.11 | If the trailer is fitted with a device enabling compressed-air actuation of the braking device, other than the parking braking device, to be cut out, the first-mentioned device must be so designed and constructed that it is positively restored to the “at rest” position not later than on the resumption of the supply of compressed air to the trailer.’