Annex Vb (Part-ML), Commission Regulation (EU) No 1321/2014 of 26 November 2014 on the continuing airworthin…

In forcesince 6 Dec 2024

ML.1

In accordance with paragraph 2 of Article 3, this Annex (Part-ML) applies to the following other than complex motor-powered aircraft not listed in the air operator certificate of an air carrier licensed in accordance with Regulation (EC) No 1008/2008:

aeroplanes of 2 730 kg maximum take-off mass (MTOM) or less;

rotorcraft of 1 200 kg MTOM or less, certified for a maximum of up to 4 occupants;

other ELA2 aircraft.

…

For the purpose of this Annex, the following definitions shall apply:

‘ independent certifying staff ’ means certifying staff who does not work on behalf of an approved maintenance organisation and who complies with, alternatively:

the requirements of Annex III (Part-66);

for aircraft to which Annex III (Part-66) does not apply, the certifying staff requirements in force under any relevant enactment;

‘ maintenance organisation ’ means an organisation holding an approval issued in accordance with, alternatively:

Subpart F of Annex I (Part-M);

Section A of Annex II (Part-145);

Section A of Annex Vd (Part-CAO).

‘ owner ’ means the person responsible for the continuing airworthiness of the aircraft, including, alternatively:

the registered owner of the aircraft;

the lessee in the case of a leasing contract;

the operator.

SECTION A

TECHNICAL REQUIREMENTS

SUBPART A

GENERAL

ML.A.101

Scope

This Section establishes the measures to be taken in order to ensure that the aircraft is airworthy. It also specifies the conditions to be met by the persons or organisations involved in the activities related to the airworthiness of the aircraft.

SUBPART B

ACCOUNTABILITY

ML.A.201

Responsibilities

The owner of the aircraft shall be responsible for the continuing airworthiness of the aircraft and shall ensure that no flight takes place unless all of the following requirements are met:

the aircraft is maintained in an airworthy condition;

any operational and emergency equipment fitted is correctly installed and serviceable or clearly identified as unserviceable;

the airworthiness certificate is valid;

the maintenance of the aircraft is performed in accordance with the Aircraft Maintenance Program ( ‘ AMP ’ ) specified in point ML.A.302.

By derogation from point (a), where the aircraft is leased, the responsibilities set out in point (a) shall apply to the lessee, if the lessee is identified either in the registration document of the aircraft or in the leasing contract.

Any person or organisation performing maintenance of aircraft and components shall be responsible for the maintenance tasks being performed.

The pilot-in-command of the aircraft shall be responsible for the satisfactory accomplishment of the preflight inspection. That inspection shall be carried out by the pilot or another qualified person but need not be carried out by an approved maintenance organisation or by certifying staff.

For aircraft operated by commercial Approved Training Organisations (‘ATO’) and commercial Declared Training Organisations (‘DTO’) referred to in Article 10a of Regulation (EU) No 1178/2011 or not operated in accordance with Annex VII to Regulation (EU) No 965/2012 (Part-NCO) or operated in accordance with Subpart-ADD of Annex II (Part-BOP) to Regulation (EU) 2018/395 or Subpart-DEC of Annex II (Part-SAO) to Regulation (EU) 2018/1976 , the operator shall:

be approved as a CAMO or as a CAO for the management of the continuing airworthiness of its aircraft in accordance with Annex Vc (Part-CAMO), Subpart G of Annex I (Part-M) or Annex Vd (Part-CAO), or contract such an organisation using the contract set out in Appendix I to this Annex;

ensure that all maintenance is performed by maintenance organisations approved in accordance with point (c)(2) of point ML.1.;

ensure that the requirements of point (a) are satisfied.

For aircraft not included in point (e), in order to satisfy the requirements of point (a), the owner of the aircraft may contract the tasks associated with continuing airworthiness management to an organisation approved as a CAMO or CAO in accordance with Annex Vc (Part-CAMO), Subpart G of Annex I (Part-M) or Annex Vd (Part-CAO). In that case, the contracted organisation shall assume responsibility for the proper performance of those tasks and a written contract shall be concluded in accordance with Appendix I to this Annex. If the owner does not contract such an organisation, the owner is responsible for the proper performance of the tasks associated with the continuing airworthiness management.

The owner shall grant the CAA access to the aircraft and the aircraft records, in order for the CAA to determine whether the aircraft complies with the requirements of this Annex.

In the case of an aircraft included in an air operator certificate is used for non-commercial or specialised operations under point ORO.GEN.310 of Annex III or point NCO.GEN.104 of Annex VII to Regulation (EU) No 965/2012 , the operator shall ensure that the tasks associated with continuing airworthiness are performed by the CAMO approved in accordance with Annex Vc (Part-CAMO) or Subpart G of Annex I (Part-M) or the combined airworthiness organisation (‘CAO’) approved in accordance with Annex Vd (Part-CAO), whichever applicable, of the air operator certificate holder.

ML.A.202

Occurrence reporting

Without prejudice to the reporting requirements set out in Annex II (Part-145) and Annex Vc (Part-CAMO), any person or organisation responsible in accordance with point ML.A.201 shall report any identified condition of an aircraft or component which endangers flight safety to:

the CAA;

to the organisation responsible for the type design or supplemental type design.

The reports referred to in point (a) shall be made in a manner determined by the CAA and shall contain all pertinent information about the condition known to the person or organisation making the report.

Where the maintenance or the airworthiness review of the aircraft is carried out on the basis of a written contract, the person or the organisation responsible for those activities shall also report any condition referred to in point (a) to the owner of the aircraft and, when different, to the CAMO or CAO concerned.

The person or organisation shall submit the reports referred to in points (a) and (c) as soon as possible, but no later than 72 hours from the moment when the person or organisation identified the condition to which the report relates, unless exceptional circumstances prevent this.

SUBPART C

CONTINUING AIRWORTHINESS

ML.A.301

Continuing airworthiness tasks

The aircraft continuing airworthiness and the serviceability of operational and emergency equipment shall be ensured by:

the accomplishment of pre-flight inspections;

the rectification of any defect and damage affecting safe operation in accordance with data specified in points ML.A.304 and ML.A.401, as applicable, while taking into account the minimum equipment list ( ‘ MEL ’ ) and configuration deviation list, when they exist;

the accomplishment of all maintenance in accordance with the AMP referred to in point ML.A.302;

the accomplishment of any applicable:

airworthiness directive ( ‘ AD ’ );

operational directive with a continuing-airworthiness impact;

continuing-airworthiness requirement established by the CAA;

measure required by the CAA as an immediate reaction to a safety problem;

the accomplishment of modifications and repairs in accordance with point ML.A.304;

maintenance check flights, when necessary.

ML.A.302

Aircraft maintenance programme

The maintenance of each aircraft shall be organised in accordance with an AMP.

The AMP and any subsequent amendments thereto shall be, alternatively:

declared by the owner in accordance with point (c)(7) of point ML.A.302, where the continuing airworthiness of the aircraft is not managed by a CAMO or CAO;

approved by the CAMO or CAO responsible for managing the continuing airworthiness of the aircraft.

The owner declaring the AMP in accordance with point (b)(1) or the organisation approving the AMP in accordance with point (b)(2) shall keep the AMP updated.

The AMP:

shall clearly identify the owner of the aircraft and the aircraft to which it relates, including any installed engine and propeller, as applicable;

shall include, alternatively:

the tasks or inspections contained in the applicable minimum inspection programme ( ‘ MIP ’ ) referred to in point (d);

the instructions for continuing airworthiness ( ‘ ICA ’ ) issued by the design approval holder ( ‘ DAH ’ );

may include additional maintenance actions to those referred to in point (c)(2) or maintenance actions alternative to those referred to in point (c)(2)(b) at the proposal of the owner, CAMO or CAO, once approved or declared in accordance with point (b). Alternative maintenance actions to those referred to in point (c)(2)(b) shall not be less restrictive than those set out in the applicable MIP;

shall include all the mandatory continuing airworthiness information, such as repetitive ADs, the airworthiness limitation section ( ‘ ALS ’ ) of the ICAs, and specific maintenance requirements contained in the type certificate data sheet ( ‘ TCDS ’ );

shall identify any additional maintenance tasks to be performed because of the specific aircraft type, aircraft configuration and type and specificity of operation, whereas the following elements shall be taken into consideration as a minimum:

specific installed equipment and modifications of the aircraft;

repairs carried out in the aircraft;

life-limited components and flight-safety-critical components;

maintenance recommendations, such as time between overhaul ( ‘ TBO ’ ) intervals, issued through service bulletins, service letters, and other non-mandatory service information;

applicable operational directives or requirements related to the periodic inspection of certain equipment;

special operational approvals;

use of the aircraft and operational environment;

shall identify whether the Pilot-owners are authorised to perform maintenance;

when declared by the owner, shall contain a signed statement by which the owner declares that this is the AMP for the particular aircraft registration and that he is fully responsible for its content and, in particular, for any deviations from the DAH's recommendations;

when approved by the CAMO or CAO, shall be signed by this organisation, which shall retain records with the justification for any deviation introduced to the DAH's recommendations;

shall be reviewed at least annually in order to assess its effectiveness, and this review shall be performed, alternatively:

in conjunction with the airworthiness review of the aircraft by the person who performs such an airworthiness review;

by the CAMO or CAO managing the continuing airworthiness of the aircraft in those cases where the review of the AMP is not performed in conjunction with an airworthiness review.

If the review shows deficiencies of the aircraft linked with deficiencies in the content of the AMP, the AMP shall be amended accordingly. In this case the person performing the review shall inform the CAA if he does not agree with the measures amending the AMP taken by the owner, CAMO or CAO. The CAA shall decide which amendments to the AMP are necessary, raising the corresponding findings and, if necessary, reacting in accordance with point ML.B.304.

A MIP:

shall contain the following inspection intervals:

for aeroplanes, touring motor gliders ( ‘ TMGs ’ ) and balloons, every annual or 100-h interval, whichever comes first, to which a tolerance of 1 month or 10 h may be applied. The next interval shall be calculated as from the time the inspection takes place;

for sailplanes and powered sailplanes other than TMG, every annual interval to which a tolerance of 1 month may be applied. The next interval shall be calculated as from the time the inspection takes place;

shall contain the following, as applicable to the aircraft type:

servicing tasks as required by the DAH's requirements;

inspection of markings;

review of weighing records and weighing in accordance with Regulation (EU) No 965/2012, Regulation (EU) 2018/395 and Regulation (EU) 2018/1976;

operational test of transponder (if installed);

functional test of the pitot-static system;

in the case of aeroplanes:

operational tests for power and revolutions per minute (rpm), magnetos, fuel and oil pressure, engine temperatures;

for engines equipped with automated engine control, the published run-up procedure;

for dry-sump engines, engines with turbochargers and liquid-cooled engines, an operational test for signs of disturbed fluid circulation;

inspection of the condition and attachment of the structural items, systems and components corresponding to the following areas:

for aeroplanes:

airframe, cabin and cockpit, landing gear, wing and centre section, flight controls, empennage, avionics and electrics, power plant, clutches and gearboxes, propeller and miscellaneous systems, such as the ballistic rescue system;

for sailplanes and powered sailplanes:

airframe, cabin and cockpit, landing gear, wing and centre section, empennage, avionics and electrics, power plant (for powered sailplanes) and miscellaneous systems, such as removable ballast and/or drag chute and controls, as well as water ballast system;

for hot-air balloons:

envelope, burner, basket, fuel containers, equipment and instruments;

for gas balloons:

envelope, basket, equipment and instruments.

As long as this Annex does not specify an MIP for airships and rotorcraft, their AMP shall be based on the ICA issued by the DAH, as referred to in point (c)(2)(b).

By derogation from points (b) and (c), a declaration by the owner or an approval by a CAMO or CAO is not required, and an AMP document is not required to be produced when the following conditions are met:

all the ICA issued by the DAH are being followed without any deviations;

all maintenance recommendations, such as TBO intervals, issued through service bulletins, service letters, and other non-mandatory service information, are being followed without any deviations;

there are no additional maintenance tasks to be performed resulting from any of the following:

specific installed equipment and modifications of the aircraft;

repairs carried out in the aircraft;

life-limited components and flight-safety-critical components;

special operational approvals;

use of the aircraft and operational environment.

Pilot-owners are authorised to perform Pilot-owner maintenance.

This derogation is not applicable if the pilot-owner or, in case of jointly-owned aircraft, any of the pilot-owners is not authorised to perform Pilot-owner maintenance because this has to be specified in the declared or approved AMP.

If the conditions provided for in points (e)(1) to (e)(4) are met, the AMP applicable to the aircraft shall consist of the following:

the ICA issued by the DAH;

the maintenance recommendations, such as TBO intervals, issued through service bulletins, service letters, and other non-mandatory service information;

the mandatory continuing airworthiness information, such as repetitive ADs, the ALS of the ICA and specific maintenance requirements contained in the TCDS;

the tasks due to specific operational or airspace directives or requirements in relation to particular instruments and equipment.

ML.A.303

Airworthiness directives

Any applicable AD must be carried out within the requirements of that AD unless otherwise specified by the CAA.

ML.A.304

Data for modifications and repairs

A person or organisation repairing an aircraft or a component shall assess any damage. Modifications and repairs shall be carried out using, as appropriate, the following data:

approved by the CAA;

approved by a design organisation complying with Annex I (Part-21) to Regulation (EU) No 748/2012;

contained in the requirements referred to in point 21.A.90B or point 21.A.431B of Annex I (Part-21) to Regulation (EU) No 748/2012.

ML.A.305

Aircraft continuing airworthiness record system

At the completion of any maintenance, the certificate of release to service (CRS) required by point ML.A.801 shall be entered in the aircraft continuing airworthiness record system. Each entry shall be made as soon as possible but not later than 30 days after the day of the completion of the maintenance task.

The aircraft continuing airworthiness records shall consist of an aircraft logbook, engine logbook(s) or engine module log cards, propeller logbook(s) and log cards, for any service-life-limited component, as appropriate.

The aircraft type and registration mark, the date together with the total flight time and flight cycles and landings, shall be entered in the aircraft logbooks.

The aircraft continuing airworthiness records shall contain:

the current status of ADs and measures mandated by the CAA in immediate reaction to a safety problem;

the current status of modifications, repairs and other DAH maintenance recommendations;

the current status of compliance with the AMP;

the current status of service-life-limited components;

the current mass and balance report;

the current list of deferred maintenance.

In addition to the authorised release document, CAA Form 1, as set out in Appendix II of Annex I (Part-M), or equivalent, the following information relevant to any component installed, such as engine, propeller, engine module or service-life-limited component, shall be entered in the appropriate engine or propeller logbook, engine module or service-life-limited component log card:

the identification of the component;

the type, serial number and registration, as appropriate, of the aircraft, engine, propeller, engine module or service-life-limited component to which the particular component has been fitted, along with the reference to the installation and removal of the component;

the date together with the component's accumulated total flight time, flight cycles, landings and calendar time, as relevant to the particular component;

the current information referred to in point (d), applicable to the component.

The person or organisation responsible for the management of continuing airworthiness and tasks pursuant to point ML.A.201, shall control the records as detailed in point ML.A.305 and present the records to the CAA upon request.

All entries made in the aircraft continuing airworthiness records shall be clear and accurate. When it is necessary to correct an entry, the correction shall be made in a manner that clearly shows the original entry.

An owner shall ensure that a system has been established to keep the following records for the periods specified:

all detailed maintenance records in respect of the aircraft and any service-life-limited component fitted thereto, until such time as the information contained therein is superseded by new information equivalent in scope and detail but no less than 36 months after the aircraft or component has been released to service;

the total time in service, this is to say hours, calendar time, cycles and landings, of the aircraft and all service-life-limited components, for at least 12 months after the aircraft or component has been permanently withdrawn from service;

the time in service, this is to say hours, calendar time, cycles and landings, as appropriate, since the last scheduled maintenance of the component subjected to a service life limit, at least until the component scheduled maintenance has been superseded by another scheduled maintenance of equivalent work scope and detail;

the current status of compliance with the AMP at least until the scheduled maintenance of the aircraft or component has been superseded by another scheduled maintenance of equivalent work scope and detail;

the current status of ADs applicable to the aircraft and components, at least 12 months after the aircraft or component has been permanently withdrawn from service;

details of current modifications and repairs to the aircraft, engine(s), propeller(s) and any other component vital to flight safety, at least 12 months after they have been permanently withdrawn from service.

ML.A.307

Transfer of aircraft continuing-airworthiness records

When an aircraft is permanently transferred from one owner to another, the transferring owner shall ensure that the continuing airworthiness records referred to in point ML.A.305 are also transferred.

When the owner contracts the continuing airworthiness management tasks to a CAMO or CAO the owner shall ensure that the continuing airworthiness records referred to in point ML.A.305 are transferred to the contracted organisation.

The time periods for the retention of records set out in point (h) of point ML.A.305 shall continue to apply to the new owner, CAMO or CAO.

SUBPART D

MAINTENANCE STANDARDS

ML.A.401

Maintenance data

The person or organisation maintaining an aircraft shall only use applicable maintenance data during the performance of maintenance.

For the purposes of this Annex, “applicable maintenance data” means any of the following:

any applicable requirement, procedure, standard or information issued by the CAA;

any applicable AD;

the applicable ICA and other maintenance instructions, issued by the type-certificate holder, supplementary type-certificate holder and any other organisation that publishes such data in accordance with Annex I (Part-21) to Regulation (EU) No 748/2012;

for components approved for installation by the design approval holder, the applicable maintenance instructions published by the component manufacturers and acceptable to the design approval holder;

any applicable data issued in accordance with point 145.A.45(d).

ML.A.402

Performance of maintenance

Maintenance performed by approved maintenance organisations shall be in accordance with Subpart F of Annex I (Part-M), Annex II (Part-145) or Annex Vd (Part-CAO), as applicable.

For maintenance not performed in accordance with point (a), the person performing maintenance shall:

be qualified for the tasks performed, as required by this Annex;

ensure that the area in which maintenance is carried out is well organised and clean with no dirt or contamination;

use the methods, techniques, standards and instructions specified in the maintenance data referred to in point ML.A.401;

use the tools, equipment and material specified in the maintenance data referred to in point ML.A.401. If necessary, tools and equipment shall be controlled and calibrated to an officially recognised standard;

ensure that maintenance is performed within any environmental limitations specified in the maintenance data referred to in point ML.A.401;

ensure that proper facilities are used in case of inclement weather or lengthy maintenance;

ensure that the risk of multiple errors during maintenance and the risk of errors being repeated in identical maintenance tasks are minimised;

ensure that an error-capturing method is implemented after the performance of any critical maintenance task;

This article is long: the rest is at the official publication.