M.1
…
SECTION A
TECHNICAL REQUIREMENTS
SUBPART A
GENERAL
M.A.101
Scope
This Section establishes the measures to be taken to ensure that the airworthiness of aircraft is maintained, including its maintenance. It also specifies the conditions to be met by the persons or organisations involved in such activities.
SUBPART B
ACCOUNTABILITY
M.A.201
Responsibilities
The owner of the aircraft shall be responsible for the continuing airworthiness of aircraft and shall ensure that no flight takes place unless all of the following requirements are met:
the aircraft is maintained in an airworthy condition;
any operational and emergency equipment fitted is correctly installed and serviceable or clearly identified as unserviceable;
the airworthiness certificate is valid;
the maintenance of the aircraft is performed in accordance with the AMP specified in point M.A.302.
When the aircraft is leased, the responsibilities of the owner are transferred to the lessee if:
the lessee is stipulated on the registration document; or
detailed in the leasing contract.
When reference is made in this Part to the ‘owner’, the term owner covers the owner or the lessee, as applicable.
Any person or organisation performing maintenance shall be responsible for the tasks performed.
The pilot-in-command or, in the case of aircraft used by air carriers licensed in accordance with Regulation (EC) No 1008/2008, the operator, shall be responsible for the satisfactory accomplishment of the pre-flight inspection. That inspection shall be carried out by the pilot or another qualified person and shall not need to be carried out by an approved maintenance organisation or by certifying staff.
In the case of aircraft used by air carriers licensed in accordance with Regulation (EC) No 1008/2008 the operator shall be responsible for the continuing airworthiness of the aircraft it operates and shall:
ensure that no flight takes place unless the conditions set out in point (a) are met;
take the necessary steps to ensure its approval as a continuing airworthiness management organisation ( ‘ CAMO ’ ) pursuant to Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M), as part of air operator certificate for the aircraft it operates;
take the necessary steps to ensure its approval in accordance with Annex II (Part-145) or conclude a written contract in accordance with point CAMO.A.315(c) of Annex Vc (Part-CAMO) or point M.A.708(c) of this Annex (Part-M) with an organisation which has been approved in accordance with Annex II (Part-145).
For complex motor-powered aircraft used for commercial specialised operations, for CAT operations other than those performed by air carriers licensed in accordance with Regulation (EC) No 1008/2008 or by commercial Approved Training Organisations (‘ATO’) and Declared Training Organisations (‘DTO’) referred to in Article 10a of Regulation (EU) No 1178/2011 , the operator shall ensure that:
no flight takes place unless the conditions set out in point (a) are met;
the tasks associated with continuing airworthiness are performed by a CAMO approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M); when the operator is not a CAMO approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M), it shall conclude a written contract as regards the performance of those tasks in accordance with Appendix I to this Annex with an organisation approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M);
the CAMO referred to in point (2) is approved in accordance with Annex II (Part-145) as an organisation to qualify for the issue of an approval for the maintenance of aircraft and of components for installation thereon, or that CAMO has concluded a written contract in accordance with point CAMO.A.315(c) of Annex Vc (Part-CAMO) or point M.A.708(c) of this Annex (Part-M) with organisations approved in accordance with Annex II (Part-145).
For complex motor-powered aircraft not included in points (e) and (f), the owner shall ensure that:
no flight takes place unless the conditions set out in point (a) are met;
the tasks associated with continuing airworthiness are performed by a CAMO approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M); when the owner is not a CAMO approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M), it shall conclude a written contract as regards the performance of those tasks in accordance with Appendix I to this Annex with an organisation approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M);
the CAMO referred to in point (2) is approved in accordance with Annex II (Part-145) as an organisation to qualify for the issue of an approval for the maintenance of aircraft and of components for installation thereon, or that CAMO has concluded a written contract in accordance with point CAMO.A.315(c) of Annex Vc (Part-CAMO) or point M.A.708(c) of this Annex (Part-M) with organisations approved in accordance with Annex II (Part-145).
For aircraft other than complex motor-powered aircraft used for commercial specialised operations or for CAT operations other than those performed by air carriers licensed in accordance with Regulation (EC) No 1008/2008, or by commercial ATOs and commercial DTOs referred to in Article 10a of Regulation (EU) No 1178/2011, the operator shall ensure that:
no flight takes place unless the conditions set out in point (a) are met;
the tasks associated with continuing airworthiness are performed by a CAMO approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M), or a combined airworthiness organisation ( ‘ CAO ’ ) approved in accordance with Annex Vd (Part-CAO); when the operator is not a CAMO approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M), or a CAO approved in accordance with Annex Vd (Part-CAO), it shall conclude a written contract in accordance with Appendix I to this Annex with a CAMO approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M), or a CAO approved in accordance with Annex Vd (Part-CAO);
the CAMO or CAO referred to in point (2) is approved in accordance with Annex II (Part-145) or in accordance with Subpart F of this Annex (Part-M), or as a CAO with maintenance privileges, or that CAMO has concluded a written contract in accordance with point CAMO.A.315(c) of Annex Vc (Part-CAMO) or point M.A.708(c) of this Annex (Part-M) with organisations approved in accordance with Annex II (Part-145) or in accordance with Subpart F of this Annex (Part-M) or Annex Vd (Part-CAO) with maintenance privileges.
For aircraft other than complex motor-powered aircraft not included in points (e) and (h), or used for limited operations, the owner shall ensure that flight takes place only if the conditions set out in point (a) are met. To that end, the owner shall:
attribute the continuing airworthiness tasks referred to in point M.A.301 to a CAMO or CAO through a written contract concluded in accordance with Appendix I; or
carry out those tasks himself; or
carry out those tasks himself except the tasks of the development of and the processing of the approval of the AMP, only if those tasks are performed by a CAMO or CAO through a limited contract concluded in accordance with point M.A.302.
The owner/operator shall ensure that any person authorised by the CAA is granted access to any of its facilities, aircraft or documents related to its activities, including any subcontracted activities, to determine compliance with this Part.
Where an aircraft included in an air operator certificate is used for non-commercial operations or specialised operations under point ORO.GEN.310 of Annex III or point NCO.GEN.104 of Annex VII to Regulation (EU) No 965/2012, the operator shall ensure that the tasks associated with continuing airworthiness are performed by the CAMO approved in accordance with Annex Vc (Part-CAMO) or Subpart G of this Annex (Part-M) or the combined airworthiness organisation ( ‘ CAO ’ ) approved in accordance with Annex Vd (Part-CAO), whichever applicable, of the air operator certificate holder.
M.A.202
Occurrence reporting
Without prejudice to the reporting requirements set out in Annex II (Part-145) and Annex Vc (Part-CAMO), any person or organisation responsible in accordance with point M.A.201 shall report any identified condition of an aircraft or component which endangers flight safety to:
the CAA;
to the organisation responsible for the type design or supplemental type design.
The reports referred to in point (a) shall be made in a manner determined by the CAA and shall contain all pertinent information about the condition known to the person or organisation making the report.
Where the maintenance or the airworthiness review of the aircraft is carried out on the basis of a written contract, the person or the organisation responsible for those activities shall also report any condition referred to in point (a) to the owner and the operator of the aircraft and, when different, to the CAMO or CAO concerned.
The person or organisation shall submit the reports referred to in points (a) and (c) as soon as possible, but no later than 72 hours from the moment when the person or organisation identified the condition to which the report relates, unless exceptional circumstances prevent this.
The person or organisation shall submit a follow-up report, providing details of actions which that person or organisation intends to take to prevent similar occurrences in the future, as soon as those actions have been identified. The follow-up report shall be submitted in a form and manner established by the CAA.
SUBPART C
CONTINUING AIRWORTHINESS
M.A.301
Continuing airworthiness tasks
The aircraft continuing airworthiness and the serviceability of operational and emergency equipment shall be ensured by:
the accomplishment of pre-flight inspections;
the rectification of any defect and damage affecting safe operation in accordance with data specified in points M.A.304 and M.A.401, as applicable, while taking into account the minimum equipment list ( ‘ MEL ’ ) and configuration deviation list, when they exist;
the accomplishment of all maintenance in accordance with the AMP referred to in point M.A.302;
the release of all maintenance in accordance with Subpart H;
for all complex motor-powered aircraft or aircraft used by air carriers licensed in accordance with Regulation (EC) No 1008/2008, the analysis of the effectiveness of the approved AMP referred to in point M.A.302;
the accomplishment of any applicable:
airworthiness directive (AD);
operational directive with a continuing airworthiness impact;
continuing airworthiness requirement established by the CAA;
measures required by the CAA in immediate reaction to a safety problem;
the accomplishment of modifications and repairs in accordance with point M.A.304;
delivering to the pilot-in-command, or to the operator in the case of air carriers licensed in accordance with Regulation (EC) No 1008/2008, the mass and balance statement reflecting the current configuration of the aircraft;
maintenance check flights, when necessary.
M.A.302
Aircraft maintenance programme
Maintenance of each aircraft shall be organised in accordance with an AMP.
The AMP and any subsequent amendments thereto shall be approved by the CAA.
When the continuing airworthiness of aircraft is managed by a CAMO or CAO, or when there is a limited contract between the owner and a CAMO or CAO concluded in accordance with point M.A.201(i)(3), the AMP and its amendments may be approved through an indirect approval procedure.
In that case, the indirect approval procedure shall be established by the CAMO or CAO concerned as part of the continuing airworthiness management exposition ( ‘ CAME ’ ) referred to in point CAMO.A.300 of Annex Vc or point M.A.704 of this Annex, or as part of the combined airworthiness exposition ( ‘ CAE ’ ) referred to in point CAO.A.025 of Annex Vd and shall be approved by the CAA.
…
The AMP shall demonstrate compliance with:
the instructions issued by the CAA;
the instructions for continuing airworthiness:
issued by the holders of the type certificate, restricted type certificate, supplemental type certificate, major repair design approval, UKTSO authorisation or any other relevant approval issued under Annex I (Part-21) to Regulation (EU) No 748/2012;
included in the certification specifications referred to in point 21.A.90B or 21.A.431B of Annex I (Part-21) to Regulation (EU) No 748/2012, if applicable;
the applicable provisions of Annex I (Part-26) to Regulation (EU) 2015/640.
By derogation to point (d), the owner or the organisation managing the continuing airworthiness of the aircraft may deviate from the instruction referred to in point (d)(2) and propose escalated intervals in the AMP, based on data obtained from sufficient reviews carried out in accordance with point (h). Indirect approval is not permitted for the escalation of safety-related tasks. The owner or the organisation managing the continuing airworthiness of the aircraft may also propose additional instructions in the AMP.
The AMP shall contain details of all maintenance to be carried out, including frequency and any specific tasks linked to the type and specificity of operations.
For complex motor-powered aircraft, when the AMP is based on maintenance steering group logic or on condition monitoring, the AMP shall include a reliability programme.
The AMP shall be subject to periodic reviews and be amended accordingly when necessary. Those reviews shall ensure that the AMP continues to be up to date and valid in light of the operating experience and instructions from the CAA , while taking into account new or modified maintenance instructions issued by the type certificate and supplemental type certificate holders and any other organisation that publishes such data in accordance with Annex I (Part-21) to Regulation (EU) No 748/2012.
M.A.303
Airworthiness directives
Any applicable airworthiness directive must be carried out within the requirements of that airworthiness directive, unless otherwise specified by the CAA.
M.A.304
Data for modifications and repairs
A person or organisation repairing an aircraft or a component, shall assess any damage. Modifications and repairs shall be carried out using, as appropriate, the following data:
approved by the CAA;
approved by a design organisation complying with Annex I (Part-21) to Regulation (EU) No 748/2012;
contained in the requirements referred to in point 21.A.90B or 21.A.431B of Annex I (Part-21) to Regulation (EU) No 748/2012.
M.A.305
Aircraft continuing airworthiness record system
At the completion of any maintenance, aircraft certificate of release to service ( ‘ CRS ’ ) required by point M.A.801 or point 145.A.50, as applicable, shall be entered in the aircraft continuing airworthiness record system, as soon as practicable and no later than 30 days after the completion of any maintenance.
The aircraft continuing airworthiness record system shall contain the following:
the date of the entry, the total in-service life accumulated in the applicable parameter for aircraft, engine(s) and/or propeller(s);
the aircraft continuing airworthiness records described in points (c) and (d) below together with the supporting detailed maintenance records described in point (e) below;
if required by point M.A.306, the aircraft technical log.
The aircraft continuing airworthiness records shall include the current mass and balance report and the current status of:
ADs and measures mandated by the CAA in immediate reaction to a safety problem;
modifications and repairs;
compliance with the AMP;
deferred maintenance tasks and deferred defects rectification.
The aircraft continuing airworthiness records shall include the current status specific to components of:
life-limited parts, including the life accumulated by each affected part in relation to the applicable airworthiness limitation parameter; and
time-controlled components, including the life accumulated by the affected components in the applicable parameter, since the last accomplishment of scheduled maintenance, as specified in the AMP.
The owner or operator shall establish a system to keep the following documents and data in a form acceptable to the CAA and for the periods specified below:
aircraft technical log system: the technical log or other data equivalent in scope and detail, covering the 36 months period prior to the last entry,
the CRS and detailed maintenance records:
demonstrating compliance with ADs and measures mandated by the CAA in immediate reaction to a safety problem applicable to the aircraft, engine(s), propeller(s) and components fitted thereto, as appropriate, until such time as the information contained therein is superseded by new information equivalent in scope and detail but covering a period not shorter than 36 months;
demonstrating compliance with the applicable data in accordance with point M.A.304 for current modifications and repairs to the aircraft, engine(s), propeller(s) and any component subject to airworthiness limitations; and
of all scheduled maintenance or other maintenance required for continuing airworthiness of aircraft, engine(s), propeller(s), as appropriate, until such time as the information contained therein is superseded by new information equivalent in scope and detail but covering a period not shorter than 36 months.
data specific to certain components:
an in-service history record for each life-limited part based on which the current status of compliance with airworthiness limitations is determined;
the CRS and detailed maintenance records for the last accomplishment of any scheduled maintenance and any subsequent unscheduled maintenance of all life-limited parts and time-controlled components until the scheduled maintenance has been superseded by another scheduled maintenance of equivalent scope and detail but covering a period not shorter than 36 months;
the CRS and owner's acceptance statement for any component that is fitted to an ELA2 aircraft without an CAA Form 1 in accordance with point 21.A.307(b)(2) of Annex I (Part-21) to Regulation (EU) No 748/2012 but covering a period not shorter than 36 months.
Record-keeping periods when the aircraft is permanently withdrawn from service:
the data required by point (b)(1) of point M.A.305 in respect of aircraft, engine(s), and propeller(s) which shall be retained for at least 12 months;
the last effective status and reports as identified under points (c) and (d) of point M.A.305 which shall be retained for at least 12 months; and
the most recent CRS(s) and detailed maintenance records as identified under points (e)(2)(ii) and (e)(3)(i) of point M.A.305 which shall be retained for at least 12 months.
The person or organisation responsible for the management of continuing airworthiness tasks pursuant to point M.A.201 shall comply with the requirements regarding the aircraft continuing airworthiness record system and present the records to the CAA upon request.
All entries made in the aircraft continuing airworthiness record system shall be clear and accurate. When it is necessary to correct an entry, the correction shall be made in a manner that clearly shows the original entry.
M.A.306
Aircraft technical log system
In addition to the requirements of point M.A.305, for CAT, commercial specialised operations and commercial ATO or commercial DTO operations, the operator shall use a technical log system containing the following information for each aircraft:
information about each flight, necessary to ensure continued flight safety, and;
the current aircraft certificate of release to service, and;
the current maintenance statement giving the aircraft maintenance status of what scheduled and out of phase maintenance is next due except that the CAA may agree to the maintenance statement being kept elsewhere, and;
all outstanding deferred defects rectifications that affect the operation of the aircraft, and;
any necessary guidance instructions on maintenance support arrangements.
The initial issue of aircraft technical log system shall be approved by the CAA. Any subsequent amendment to that system shall be managed in accordance with point CAMO.A.300(c), or points M.A.704(b) and (c), or point CAO.A.025(c).
…
M.A.307
Transfer of aircraft continuing airworthiness records
When an aircraft is permanently transferred from one owner or operator to another, the transferring owner or operator shall ensure that the continuing airworthiness records referred to in point M.A.305 and, if applicable the technical log system referred to in point M.A.306, are also transferred.
When the owner contracts the continuing airworthiness management tasks to a CAMO or CAO, the owner shall ensure that the continuing airworthiness records referred to in point M.A.305 are transferred to that contracted organisation.
The time periods for the retention of records set out in point (e) of point M.A.305 shall continue to apply to the new owner, operator, CAMO or CAO.
SUBPART D
MAINTENANCE STANDARDS
M.A.401
Maintenance data
The person or organisation maintaining an aircraft must have access to and use only current applicable maintenance data in the performance of maintenance including modifications and repairs.
For the purposes of this Part, applicable maintenance data is:
any applicable requirement, procedure, standard or information issued by the CAA,
any applicable airworthiness directive,
the applicable instructions for continued airworthiness and any other maintenance instructions issued by the type-certificate holder, supplementary type-certificate holder and any other organisation that publishes such data in accordance with Annex I (Part 21) to Regulation (EU) No 748/2012,
for components approved for installation by the design approval holder, the applicable maintenance instructions published by the component manufacturers and acceptable to the design approval holder,
any applicable data issued in accordance with point 145.A.45(d).
The person or organisation maintaining an aircraft must ensure that all applicable maintenance data is current and readily available for use when required. The person or organisation must establish a work card or worksheet system to be used and must either transcribe accurately the maintenance data onto such work cards or worksheets or make precise reference to the particular maintenance task or tasks contained in such maintenance data.
M.A.402
Performance of maintenance
Except for maintenance performed by a maintenance organisation approved in accordance with Annex II (Part-145), any person or organisation performing maintenance shall:
be qualified for the tasks performed, as required by this part;