One test report shall be completed for each tests required for EU type-approval.
Each additional (e.g. a second speed on a constant speed engine) or supplementary test (e.g. another fuel is tested) will require an additional or supplementary test report.
2.1.
A test report shall contain at least the information set out in Appendix 1;
2.2.
Notwithstanding point 2.1, only those sections or sub-sections relevant for the particular test and for the particular engine family, engine types within the engine family or engine type tested need to be stated in the test report (e.g. if a NRTC is not run this section may be omitted);
2.3.
The test report may contain more information than that requested in point 2.1 but in any case, shall adhere to the proposed numbering system;
2.4.
Where several options separated by forward slash are given for an entry, the unused options shall be struck out, or only the used option(s) shall be shown;
2.5.
Where a ‘type’ of a component is requested, the information supplied shall uniquely identify the component; this may be a list of characteristic, a manufacturers' name and part or drawing number, a drawing, or a combination of the aforementioned or other methods that achieves the same result.
2.6.
The test report may be delivered on paper or in an electronic format agreed between the manufacturer, technical service and approval authority.
1.1.
Make(s) (trade name(s) of manufacturer): …
1.2.
Commercial name(s) (if applicable): …
1.3.
Company name and address of manufacturer: …
1.4.
Name of technical service: …
1.5.
Address of technical service: …
1.6.
Location of test: …
1.7.
Date of test: …
1.8.
Test report number: …
1.9.
Information document reference number (if available): …
1.10.
Test report type: Primary test/additional test/supplementary test
1.10.1.
Description of the purpose of the test: …
2.1.
Engine type designation/engine family designation/FT: …
2.2.
Engine identification number: …
2.3.
Engine Category and subcategory: NRE-v-1/NRE-v-2/NRE-v-3/NRE-v-4/NRE-v-5/NRE-v-6/NRE-v-7/NRE-c-1/NRE-c-2/NRE-c-3/NRE-c-4/NRE-c-5/NRE-c-6/NRE-c-7/NRG-v-1/NRG-c-1/NRSh-v-1a/NRSh-v-1b/NRS-vr-1a/NRS-vr-1b/ NRS-vi-1a/NRS-vi-1b/NRS-v-2a/NRS-v-2b/NRS-v-3/IWP-v-1/IWP-v-2/IWP-v-3/IWP-v-4/IWP-c-1/IWP-c-2/IWP-c-3/IWP-c-4/IWA-v-1/IWA-v-2/IWA-v-3/IWA-v-4/IWA-c-1/IWA-c-2/IWA-c-3/IWA-c-4/RLL-v-1/RLL-C-1/RLR-v-1/RLR-C-1/SMB-v-1/ATS-v-1
3.1.
Engine mapping documentation reference: …
3.2.
Deterioration factor determination documentation reference: …
3.3.
Infrequent regeneration factors determination documentation reference, where applicable: …
3.4.
NOx control diagnostic demonstration documentation reference, where applicable: …
3.5.
Particulate control diagnostic demonstration documentation reference, where applicable:
3.6.
For engine types and engine families that use an ECU as part of the emission control system anti-tampering declaration documentation reference: …
3.7.
For engine types and engine families that use mechanical devices as part of the emission control system anti-tampering and adjustable parameters declaration and demonstration documentation reference: …
3.8.
Manufacturer intends to use ECU torque signal for in-service monitoring: Yes/No
3.8.1.
dynamometer torque greater than or equal to 0,93 × ECU torque: Yes/No
3.8.2.
ECU torque correction factor in case that dynamometer torque less than 0,93 × ECU torque: …
4.1.1.
Make: …
4.1.2.
Type: …
4.1.3.
Octane number RON: …
4.1.4.
Octane number MON: …
4.1.5.
Ethanol content ( %): …
4.1.6.
Density at 15 Deg.C (kg/m3): …
4.2.1.
Make: …
4.2.2.
Type: …
4.2.3.
Cetane number: …
4.2.4.
Fame content ( %): …
4.2.5.
Density at 15 Deg.C (kg/m3): …
4.3.1.
Make: …
4.3.2.
Type: …
4.3.3.
Reference fuel type: Fuel A/Fuel B
4.3.4.
Octane number MON: …
4.4.1.
Reference fuel type: GR/G23/G25/G20
4.4.2.
Source of reference gas: specific reference fuel/pipeline gas with admixture
4.4.3.1.
Make: …
4.4.3.2.
Type: …
4.4.4.1.
Admixture(s): Carbon dioxide/Ethane/Methane/Nitrogen/Propane
4.4.4.2.
The value of Sλ for the resulting fuel blend: …
4.4.4.3.
The Methane Number (MN) of the resulting fuel blend: …
4.5.1.
Gas energy ratio on test cycle: …
5.1.
Make(s): …
5.2.
Type(s): …
5.3.
SAE viscosity: …
5.4.
Lubricant and fuel are mixed: yes/no
5.4.1.
Percentage of oil in mixture: …
6.1.
100 % speed (rpm): …
6.1.1.
100 % speed determined by: Declared rated speed/Declared maximum test speed (MTS)/Measured MTS
6.1.2.
Adjusted MTS if applicable (rpm): …
6.2.
Intermediate speed: …
6.2.1.
Intermediate speed determined by: Declared intermediate speed/Measured intermediate speed/60 % of 100 % speed/75 % of 100 % speed/85 % of 100 % speed
6.3.
Idle speed: …
7.1.1.
Power absorbed at indicated engine speeds by necessary auxiliaries for engine operation that cannot be fitted for the test (as specified by the manufacturer) to be stated in Table 1:
Auxiliary type and identifying details |
Power absorbed by auxiliary (kW) at indicated engine speed
(complete relevant columns)
Idle | 63 % | 80 % | 91 % | Inter-mediate | Max. power | 100 %
Total (Pf,i): | | | | | | |
7.1.2.
Power absorbed at indicated engine speeds by auxiliaries linked with the operation of the non-road mobile machinery that cannot be removed for the test (as specified by the manufacturer) to be stated in Table 2:
Auxiliary type and identifying details |
Power absorbed by auxiliary (kW) at indicated engine speed
(complete relevant columns)
Idle | 63 % | 80 % | 91 % | Inter-mediate | Max. power | 100 %
Total (Pr,i): | | | | | | |
7.2.
Engine net power to be stated in Table 3:
Condition |
Engine net power (kW) at indicated engine speed
(complete relevant columns)
Intermediate | Max. power | 100 %
Reference power measured at specified test speed (Pm,i) | | |
Total auxiliary power from Table 1 (Pf,i) | | |
Total auxiliary power from Table 2 (Pr,i) | | |
Engine net power
Pi = Pm,I – Pf,i + Pr,i
8.1.
fa within range 0,93 to 1,07: Yes/No
8.1.1.
If fa is not within specified range state altitude of test facility and dry atmospheric pressure: …
8.2.
Applicable intake air temperature range: 20 to 30/0 to – 5(snow throwers only)/– 5 to – 15(snowmobiles only)/20 to 35(NRE greater than 560 kW only)
9.1.
Cycle (mark cycle used with X) to be stated in Table 4:
Cycle | C1 | C2 | D2 | E2 | E3 | F | G1 | G2 | G3 | H
Discrete mode | | | | | | | | | |
RMC | | | | | | | | | N/A |
9.2.
Dynamometer setting (kW) to be stated in Table 5:
[The dynamometer setting shall be determined using the procedure set out in point 7.7.1.3 of Annex VI to Delegated Regulation (EU) 2017/654. The auxiliary power in that point shall be determined using the total values set out in Tables 1 and 2 of this Appendix.]
% Load at point or % of rated power (as applicable) |
Dynamometer setting (kW) at indicated engine speed after adjustment for auxiliary power
(complete relevant columns)
Idle | 63 % | 80 % | 91 % | Inter-mediate | 100 %
5 % | | | | | |
10 % | | | | | |
25 % | | | | | |
50 % | | | | | |
75 % | | | | | |
100 % | | | | | |
9.3.1.
Deterioration Factor (DF): calculated/assigned
9.3.2.
DF values and the cycle weighted emissions results to be stated in Table 6:
Note: In the event that a discrete mode NRSC is run where the Kru or Krd factors have been established for individual modes then a table showing each mode and the applied Kru or Krd should replace the shown table
DF
mult/add
CO | HC | NOx | HC+NOx | PM | PN
Emissions | CO (g/kWh) | HC (g/kWh) | NOx (g/kWh) | HC+NOx (g/kWh) | PM (g/kWh) | PN #/kWh
Test result with/without regeneration | | | | | |
kru/krd
mult/add
test result with infrequent regeneration adjustment factors (IRAFs) | | | | | |
Final test result with DF | | | | | |
9.3.3.
Cycle weighted CO2 (g/kWh): …
9.3.4.
Cycle weighted NH3 (ppm): …
9.4.
Additional control area test points (if applicable) to be stated in Table 7:
Emissions at test point | Engine Speed | Load (%) | CO (g/kWh) | HC (g/kWh) | NOx (g/kWh) | HC+NOx (g/kWh) | PM (g/kWh) | PN n/kWh
Test result 1 | | | | | | | |
Test result 2 | | | | | | | |
Test result 3 | | | | | | | |
9.5.
Sampling systems used for the NRSC test: …
9.5.1.
Gaseous emissions: …
9.5.2.
PM: …
9.5.2.1.
Method: single/multiple filter
9.5.3.
Particle number: …
10.1.
Cycle (mark cycle with X) to be stated in Table 8:
NRTC |
LSI-NRTC |
10.2.
Transient test deterioration factors:
10.2.1. Deterioration Factor (DF): calculated/fixed
10.2.2. DF values and the emissions results to be stated in Table 9 or Table 10
10.3.
NRTC emission results:
DF
mult/add
CO | HC | NOx | HC+NOx | PM | PN
Emissions | CO (g/kWh) | HC (g/kWh) | NOx (g/kWh) | HC+NOx (g/kWh) | PM (g/kWh) | PN (#/kWh)
Cold start | | | | | |
Hot start test result
with/without regeneration
Weighted test result | | | | | |
kru/krd
mult/add
Weighted test result with IRAFs | | | | | |
Final test result with DF | | | | | |
10.3.1. Hot cycle CO2 (g/kWh):
10.3.2. Cycle average NH3 (ppm):
10.3.3. Cycle work for hot start test (kWh):
10.3.4. Cycle CO2 for hot start test (g):
10.4.
LSI-NRTC emission results
DF
mult/add
CO | HC | NOx | HC+NOx | PM | PN
Emissions | CO (g/kWh) | HC (g/kWh) | NOx (g/kWh) | HC+NOx (g/kWh) | PM (g/kWh) | PN (#/kWh)
test result
with/without regeneration
kru/krd
mult/add
Test result with IRAFs | | | | | |
Final test result with DF | | | | | |
10.4.1. Cycle CO2 (g/kWh):
10.4.2. Cycle average NH3 (ppm):
10.4.3. Cycle work (kWh):
10.4.4. Cycle CO2 (g):
10.5.
Sampling system used for the transient test:
10.5.1. Gaseous emissions:
10.5.2. PM:
10.5.3. Particle number:
11.1.
Cycle emissions results to be stated in Table 11.
Emissions |
CO
(g/kWh)
HC
(g/kWh)
NOx
(g/kWh)
HC+NOx
(g/kWh)
PM
(g/kWh)
PN
(#/kWh)
Test Cycle (1)
NRSC final result with DF (2). | | | | | | |
Final transient test result with DF (3) | | | | | | |
11.2.
CO2 result (4):
11.3.
In service monitoring reference values (5)
11.3.1.
Reference work (kWh) (6):
11.3.2.
Reference CO2 mass (g) (7):
For NRSC indicate the cycle noted in point 9.1 (Table 4); for transient test indicate cycle noted in point 10.1 (Table 8).
Copy the ‘Final test result with DF’ results from Table 6.
Copy ‘Final test result with DF’ results from Table 9 or 10, as applicable.
For an engine type or engine family that is tested on both the NRSC and a transient cycle, indicate the hot cycle CO2 emissions values from the NRTC noted in point 10.3.4 or the CO2 emissions values from the LSI-NRTC noted in point 10.4.4. For an engine only tested on an NRSC indicate the CO2 emissions values given in that cycle noted in point 9.3.3.
Only applicable to engines of sub-categories NRE-v-5 and NRE-v-6 tested on NRTC.
Indicate the cycle work for hot start test value from the NRTC noted in point 10.3.3.
Indicate the cycle CO2 for hot start test value from the NRTC noted in point 10.3.4.