ANNEX V, Regulation (EU) 2017/656

In forcesince 7 Aug 2018cited 1×

1.

EU type-approval certificates shall be numbered in accordance with the method set out in this Annex.

2.

The EU type-approval number shall consist of a total of five sections as detailed below. In all cases, the sections shall be separated by an asterisk (‘*’).

2.1.

Section 1 denotes the Member State issuing the EU type-approval; begins with the lower-case letter ‘e’ and is followed by the distinguishing number of the Member State, applicable for all EU type-approval numbers:

1 | Germany | 19 | Romania

2 | France | 20 | Poland

3 | Italy | 21 | Portugal

4 | The Netherlands | 23 | Greece

5 | Sweden | 24 | Ireland

6 | Belgium | 25 | Croatia

7 | Hungary | 26 | Slovenia

8 | Czech Republic | 27 | Slovakia

9 | Spain | 29 | Estonia

11 | United Kingdom | 32 | Latvia

12 | Austria | 34 | Bulgaria

13 | Luxembourg | 36 | Lithuania

17 | Finland | 49 | Cyprus

18 | Denmark | 50 | Malta

2.2.

Section 2: denotes the number Regulation (EU) 2016/1628 of the European Parliament and of the Council in the form 2016/1628.

2.3.

Section 3 denotes three separate elements:

2.3.1. the number of the latest amending Regulation applicable to the EU type-approval. If there is no amending Regulation, the Regulation referred to in point 2.2 is repeated;

2.3.2. this number is followed by the applicable Engine Category Identification Code from column 4 of Table 1 in Appendix 1;

2.3.3. to be further followed by a slash (‘/’) and the applicable Fuel Type Code from column 3 of Table 2 of Appendix 1;

2.3.3.1. in the case of dual fuel engines, the applicable Duel Fuel Suffix from column 2 of Table 3 is added to denote the gaseous fuel;

2.4.

Section 4: denotes the EU type-approval number and consists of a sequential number with leading zeros (as applicable) and four digits starting from ‘0001’;

2.5.

Section 5: denotes the extension number of the EU type-approval and consists of a two-digit sequential number, with leading zero (as applicable) starting from ‘00’.

2.6.

Where used on the engine's statutory marking only, section 2.5 shall be omitted.

3.1.

Example of a EU type-approval number of an NRSh-v-1b engine operating on petrol fuel, issued by the Netherlands, which has been extended three times:

e4*2016/1628*2017/RRRSHB3/P*0078*03

e4The Netherlands (section 1)

2016/1628Regulation (EU) 2016/1628 (section 2)

2017/RRRSHB3/PRegulation (EU) 2017/RRR to denote the latest amending Regulation and the characters ‘SHB3/P’ to indicate that is an engine of category and subcategory NRSh-v-1b, with EDP Category 3, operating on petrol, in accordance with the Codes set out in Tables 1 and 2 of Appendix 1 respectively (section 3).

0078EU type-approval sequential number (section 4)

03extension number (section 5)

Where used for statutory marking this number would be displayed as:

e4*2016/1628*2017/RRRSHB3/P*0078

3.2.

Example of a EU type-approval number of a NRE-c-3 type 1A dual fuel engine operating on gaseous fuel of type LN2 (a specific liquefied natural gas/liquefied biomethane composition resulting in a λ-shift factor not differing by more than 3 per cent the λ-shift factor of the G20 gas specified in Annex I to Delegated Regulation (EU) 2017/654 and the ethane content of which does not exceed 1,5 per cent), which has not yet been extended, issued by France:

e2*2016/1628*2016/1628EC3/1A7*0003*00

e2France (section 1)

2016/1628Regulation (EU) 2016/1628 (section 2)

2016/1628EC3/1A7repeats Regulation (EU) 2016/1628 to denote that it has not been amended. The characters ‘EC3’ denote that is a NRE-c-3 engine. The characters ‘1A’ denote it is a dual fuel engine of type ‘1A’. The suffix 7 to denote that the gaseous fuel is of type ‘LN2’ (a specific liquefied natural gas / liquefied biomethane composition resulting in a λ-shift factor not differing by more than 3 per cent the λ-shift factor of the G20 gas specified in Annex I to Delegated Regulation (EU) 2017/654 and the ethane content of which does not exceed 1,5 per cent), in accordance with the Codes set out in Tables 1 to 3 of Appendix 1 respectively (section 3).

0003EU type-approval sequential number (section 4)

00extension number (section 5)

Where used for statutory marking this number would be displayed as:

e2*2016/1628*2016/1628 EC3/1A7*0003

3.3.

Example of a EU type-approval number of a RLL-v-1 engine according to the SPE emission limits operating on diesel fuel, issued by Austria, which has been extended 2 times:

e12*2016/1628*2017/RRRLV1S/D*0331*02

e12Austria (section 1)

2016/1628Regulation (EU) 2016/1628 (section 2)

2017/RRRLV1S/DRegulation (EU) 2017/RRR to denote the latest amending Regulation and the characters ‘LV1S/D’ to indicate that is a locomotive engine meeting the SPE emission limits type-approved to run on diesel, in accordance with the Codes set out in Tables 1 and 2 of Appendix 1 respectively (section 3).

0331EU type-approval sequential number (section 4)

02extension number (section 5)

Where used for statutory marking this number would be displayed as:

e12*2016/1628*2017/RRRLV1S/D*0331

Engine Category

(column 1)

Engine Subcategory

(column 2)

EDP Category

(where applicable)

(column 3)

Engine Category Identification Code

(column 4)

Engines Subject to the exhaust emission limits in Annex II to Regulation (EU) 2016/1628

NRE | NRE-v-1 | | EV1

NRE-v-2 | | EV2

NRE-v-3 | | EV3

NRE-v-4 | | EV4

NRE-v-5 | | EV5

NRE-v-6 | | EV6

NRE-v-7 | | EV7

NRE-c-1 | | EC1

NRE-c-2 | | EC2

NRE-c-3 | | EC3

NRE-c-4 | | EC4

NRE-c-5 | | EC5

NRE-c-6 | | EC6

NRE-c-7 | | EC7

NRG | NRG-v-1 | | GV1

NRG-c-1 | | GC1

NRSh | NRSh-v-1a | Cat 1 | SHA1

Cat 2 | SHA2

Cat 3 | SHA3

NRSh-v-1b | Cat 1 | SHB1

Cat 2 | SHB2

Cat 3 | SHB3

NRS

(Other than those engines tested at low temperature only for use in snow throwers)

NRS-vr-1a | Cat 1 | SRA1

Cat 2 | SRA2

Cat 3 | SRA3

NRS-vr-1b | Cat 1 | SRB1

Cat 2 | SRB2

Cat 3 | SRB3

NRS-vi-1a | Cat 1 | SYA1

Cat 2 | SYA2

Cat 3 | SYA3

NRS-vi-1b | Cat 1 | SYB1

Cat 2 | SYB2

Cat 3 | SYB3

NRS-v-2a | Cat 1 | SVA1

Cat 2 | SVA2

Cat 3 | SVA3

NRS-v-2b | Cat 1 | SVB1

Cat 2 | SVB2

Cat 3 | SVB3

NRS-v-3 | Cat 1 | SV31

Cat 2 | SV32

Cat 3 | SV33

NRS

(Engines tested at low temperature only for use in snow thrower)

NRS-vr-1a | Cat 1 | TRA1

Cat 2 | TRA2

Cat 3 | TRA3

NRS-vr-1b | Cat 1 | TRB1

Cat 2 | TRB2

Cat 3 | TRB3

NRS-vi-1a | Cat 1 | TYA1

Cat 2 | TYA2

Cat 3 | TYA3

NRS-vi-1b | Cat 1 | TYB1

Cat 2 | TYB2

Cat 3 | TYB3

IWP | IWP-v-1 | | PV1

IWP-v-2 | | PV2

IWP-v-3 | | PV3

IWP-v-4 | | PV4

IWP-c-1 | | PC1

IWP-c-2 | | PC2

IWP-c-3 | | PC3

IWP-c-4 | | PC4

IWA | IWA-v-1 | | AV1

IWA-v-2 | | AV2

IWA-v-3 | | AV3

IWA-v-4 | | AV4

IWA-c-1 | | AC1

IWA-c-2 | | AC2

IWA-c-3 | | AC3

IWA-c-4 | | AC4

RLL | RLL-v-1 | | LV1

RLL-c-1 | | LC1

RLR | RLR-v-1 | | RV1

RLR-c-1 | | RC1

SMB | SMB-v-1 | | SM1

ATS | ATS-v-1 | | AT1

Engines Subject to the exhaust emission limits in Annex VI to Regulation (EU) 2016/1628

SPE

SPE-NRE | SPE-NRE-v-1 | | EV1S

SPE-NRE-v-2 | | EV2S

SPE-NRE-v-3 | | EV3S

SPE-NRE-v-4 | | EV4S

SPE-NRE-v-5 | | EV5S

SPE-NRE-v-6 | | EV6S

SPE-NRE-v-7 | | EV7S

SPE-NRE-c-1 | | EC1S

SPE-NRE-c-2 | | EC2S

SPE-NRE-c-3 | | EC3S

SPE-NRE-c-4 | | EC4S

SPE-NRE-c-5 | | EC5S

SPE-NRE-c-6 | | EC6S

SPE-NRE-c-7 | | EC7S

SPE-NRG | SPE-NRG-v-1 | | GV1S

SPE-NRG-c-1 | | GC1S

SPE-RLL | SPE-RLL-v-1 | | LV1S

SPE-RLL-c-1 | | LC1S

[Replace ‘#’ with approved gas specification from Table 3.]

Engine Fuel type

(column 1)

Sub-type, where applicable

(column 2)

Fuel Type Code

(column 3)

Diesel (non-road gas-oil) fuelled CI engine | | D

Dedicated Ethanol (ED95) fuelled CI engine | | ED

Ethanol (E85) fuelled SI engine | | E85

Petrol (E10) fuelled SI engine | | P

LPG fuelled SI engine | | Q

Natural gas/biomethane fuelled SI engine | Engine approved and calibrated for the H-range of gases | H

Engine approved and calibrated for the L-range of gases | L

Engine approved and calibrated for both the H-range and L-range of gases | HL

Engine approved and calibrated for a specific gas composition in the H-range of gases and transformable to another specific gas in the H-range of gases by fine tuning of the engine fuelling | HT

Engine approved and calibrated for a specific gas composition in the L-range of gases and transformable to another specific gas in the L-range of gases after fine tuning of the engine fuelling | LT

Engine approved and calibrated for a specific gas composition in either the H-range or the L-range of gases and transformable to another specific gas in either the H-range or the L-range of gases by fine tuning of the engine fuelling | HLT

Engine approved and calibrated for a specific liquefied natural gas / liquefied biomethane composition resulting in a λ-shift factor not differing by more than 3 per cent the λ-shift factor of the G20 gas specified in Annex I to Delegated Regulation (EU) 2017/654 and the ethane content of which does not exceed 1,5 per cent | LN2

Engine approved and calibrated for any other (than above) liquefied natural gas / liquefied biomethane composition. | LNG

Dual-fuel engines | for dual-fuel engines of Type 1A | 1A#

for dual-fuel engines of Type 1B | 1B#

for dual-fuel engines of Type 2A | 2A#

for dual-fuel engines of Type 2B | 2B#

for dual-fuel engines of Type 3B | 3B#

Approved Gas specification |

Dual Fuel Suffix

(column 2)

Dual fuel engine approved and calibrated for the H-range of gases as gaseous component of fuel | 1

Dual fuel engine approved and calibrated for te L-range of gases as gaseous component of fuel | 2

Dual fuel engine being and calibrated for both the H-range and L-range of gases as gaseous component of fuel | 3

Dual fuel engine approved and calibrated for a specific gas composition in the H-range of gases and transformable to another specific gas in the H-range of gases by fine tuning of the engine fuelling as gaseous component of fuel | 4

Dual fuel engine approved and calibrated for a specific gas composition in the L-range of gases and transformable to another specific gas in the L-range of gases after fine tuning of the engine fuelling as gaseous component of fuel | 5

Dual fuel engine approved and calibrated for a specific gas composition in either the H-range or the L-range of gases and transformable to another specific gas in either the H-range or the L-range of gases by fine tuning of the engine fuelling as gaseous component of fuel | 6

Dual fuel engine approved and calibrated for a specific liquefied natural gas / liquefied biomethane composition resulting in a λ-shift factor not differing by more than 3 per cent the λ-shift factor of the G20 gas specified in Annex I to Delegated Regulation (EU) 2017/654 and the ethane content of which does not exceed 1,5 per cent as gaseous component of fuel | 7

Dual fuel engine approved and calibrated for any other (than above) liquefied natural gas / liquefied biomethane composition as gaseous component of fuel | 8

Dual fuel engine approved for operation on LPG as gaseous component of fuel | 9