1.1.
The following requirements apply to vehicles with eCall in-vehicle system installed, STUs and (optionally for) components.
1.2.1.
The eCall system shall carry out a self-test at each system power-up.
1.2.2.
The self-test function shall monitor at least the technical items listed in the Table.
1.2.3.
A warning in form of either a visual tell-tale or a warning message in a common space shall be provided in case a failure is detected by the self-test function.
1.2.3.1.
It shall remain activated while the failure is present.
1.2.3.2.
It may be cancelled temporarily, but shall be repeated whenever the ignition or vehicle master control switch is being activated.
1.3.1.
The manufacturer shall provide the technical service and the type-approval authority with documentation in accordance with the Table, which shall contain for each item the technical principle applied to monitor the item.
Item | Technical principle applied for monitoring
eCall ECU is in working order (e.g. no internal hardware failure, processor/memory is ready, logic function in expected default state) |
Mobile network antenna is connected |
Mobile network communication device is in working order (no internal hardware failure, responsive) |
GNSS antenna is connected |
GNSS receiver is in working order (no internal hardware failure, output within expected range) |
Crash control unit is connected |
No communication failures (bus connection failures) of relevant components in this table |
SIM is present (this item only applies if a removable SIM is used) |
Power source is connected |
Power source has sufficient charge (threshold at the discretion of the manufacturer) |
2.1.1.
The following test shall be performed, separately for each of the items listed in the Table, on the vehicle with an eCall in-vehicle system installed in accordance with Article 5, on the STU in accordance with Article 7 or on the component, that is made part of a complete system for the purpose of the test, in accordance with Article 6.
2.1.2.
Simulate a malfunction of the eCall system by introducing a critical failure monitored by the self-test function according to the technical documentation provided by the manufacturer. The manufacturer shall provide a list of the checks and a description of how to trigger them.
2.1.3.
Power the eCall system up (e.g. by switching the ignition ‘on’ or activating the vehicle's master control switch, as applicable) and verify that the malfunction indicator illuminates shortly afterwards.
2.1.4.
Power the eCall system down (e.g. by switching the ignition ‘off’ or deactivating the vehicle's master control switch, as applicable) and restore it to normal operation.
2.1.5.
Power the eCall system up and verify that the malfunction indicator does not illuminate or extinguishes shortly after illuminating initially. For the failures which cannot be simulated or injected by the technical service, the manufactures shall provide a documentation describing the test procedure and the test results to the technical service.
3.1.
When the manufacturer submits an application for revision or extension of an existing type-approval for the purpose of including an alternative GNSS antenna, electronic control unit, mobile network antenna and/or power source components, no retesting of 112-based eCall in-vehicle system components shall be required for the purpose of fulfilling the requirements of this Annex, provided that those type-approved components possess at least the same functional features and that they are covered by this Annex in accordance with Article 6(3).
The purpose shall be to verify the following features of the eCall system:
its correct operational status, by visual observation of the failure warning signal status following the activation of the vehicle master control switch and any bulb check. Where the failure warning signal is only displayed in a common space (the area on which two or more information functions or symbols may be displayed, but not simultaneously), it must be checked first that the common space is functional prior to the failure warning signal status check;
the correct accuracy of the Minimum Set of Data (by generating and reading current MSD), the correct function and condition of the eCall components and the backup-battery (if applicable), by the use of an electronic vehicle interface;
the software integrity, by external verification of version information, hash values and system configurations against reference data;
the correct functionality of the voice communication, by performing an audio echo and speaker test using the vehicle interface.
4.2.1. The 112-based eCall in-vehicle system shall be able to provide the information to perform the methods of testing specified in Section 3, point 7.13, of Annex I to Directive 2014/45/EU using the electronic vehicle interface.
4.2.2. The manufacturer shall make available the technical information, which shall contain the instructions for reading out the information or performing the checks related to each item specified in Section 3, point 7.13, of Annex I to Directive 2014/45/EU.
4.3.1. It shall be verified that the information related to each item specified in Section 3, point 7.13 of Annex I to Directive 2014/45/EU, can be read out from the eCall system using the electronic vehicle interface according to the instructions of the manufacturer.
4.3.2. It shall be verified that an echo and speaker test can be performed to check the correct functionality of the voice communication via the vehicle interface.