1.1.
The following requirements apply to 112-based eCall in-vehicle systems, STUs and (optionally for) components that shall be used in conjunction with a TPS eCall in-vehicle system.
1.1.1.
In case of an optional TPS eCall system, the TPS eCall related tests set out in section 9.8 of standard EN 16454:2023 remain applicable for the Declaration of Conformity of eCall in-vehicle system after 31 December 2025.
1.2.1.
The 112-based system shall be deactivated as long as the TPS system is active and does function.
1.2.2.
The 112-based system shall be automatically triggered in the event that the TPS system is triggered but does not function.
1.3.1.
The manufacturer shall provide the technical service with an explanation of the design provisions built into the TPS system to ensure automatic triggering of the 112-based system (‘fall-back procedure’) in the event that the TPS system does not function. This documentation shall describe the principles of the changeover mechanism.
1.3.2.
The documentation shall be supported by an analysis which shows, in overall terms, any hardware or software failure conditions that would result in an inability of the TPS system to perform a successful call and how the TPS system will behave on the occurrence of these.
This may be based on a Failure Mode and Effect Analysis (FMEA), a Fault Tree Analysis (FTA) or any appropriate similar process as agreed between the technical service and the manufacturer.
The chosen analytical approach(es) shall be established and maintained by the manufacturer and shall be made open for inspection by the technical service at the time of the type-approval.
The purpose of this test procedure is to verify for eCall in-vehicle systems that shall be used in conjunction with a TPS eCall in-vehicle system, that there is only one system active at a time and that the 112-based system is triggered automatically in the event that the TPS system does not function.
2.2.
The following tests shall be performed either on a vehicle with an eCall in-vehicle system installed or on a representative arrangement of parts.
2.3.
The deactivation of the 112-based system while the TPS system is active, shall be verified by performing a manually triggered test eCall.
2.3.1.
Before performing the test eCall, ensure:
that one of the connection procedures specified in point 2.7 of Annex I, as agreed between the technical service and the manufacturer, will be applied for any test eCall;
that the dedicated PSAP test point is available to receive an eCall emitted by the 112-based system;
that the TPSP test point is available to receive an eCall emitted by the TPS system;
that a false eCall to a genuine PSAP cannot be made over the live network; and
that the vehicle ignition or master control switch is activated.
2.3.2.
Perform a test eCall by applying a manual trigger of the TPS system.
2.3.3.
Verify that:
an eCall was established with the TPSP test point by a successful voice connection to the TPSP test point;
data was received properly at the TPSP test point including at least the MSD; and
no eCall was attempted or established with the PSAP test point by a record of the PSAP test point showing that it did not receive an eCall.
2.3.4.
Clear down the eCall using the appropriate TPSP test point command (e.g. hang up).
2.3.5.
If the call attempt of the TPS system fails during the test, the test procedure may be repeated.
2.4.
The fall-back procedure and activation of the 112-based system, in the event that the TPS system does not function, shall be verified by performing a manually triggered test eCall.
2.4.1.
Modify the TPS system to simulate a failure, selected at the discretion of the technical service that shall result in a fall-back procedure based on the documentation provided by the manufacturer. Such selection shall be documented in the test report.
2.4.2.
Before performing the test eCall, ensure that:
one of the connection procedures defined in point 2.7 of Annex I, as agreed between the technical service and the manufacturer, will be applied for any test eCall;
the dedicated PSAP test point is available to receive an eCall emitted by the 112-based system;
a false eCall to a genuine PSAP cannot be made over the live network; and
the vehicle ignition or master control switch is activated.
2.4.3.
Perform a test eCall by applying a manual trigger of the TPS system.
2.4.4.
Verify that:
an eCall was established with the PSAP test point by a successful voice connection to the PSAP test point; and
an MSD was received by the PSAP test point. That shall be verified by a record of the PSAP test point showing that an MSD emitted from the eCall system following the trigger was received and successfully decoded.
2.4.5.
Clear down the test eCall using the appropriate PSAP test point command (e.g. hang up).
The connection procedures defined in point 2.7 of Annex I to this Regulation shall apply.