ANNEX VII, Commission Regulation (EU) No 965/2012 of 5 October 2012 laying down technical requireme…

In forcesince 22 Feb 2026cited 15×
(a)

The competent authority shall be the authority designated by the Member State where the aircraft is registered.

(b)

If the aircraft is registered in a third country, the competent authority shall be the authority designated by the Member State where the operator has its principal place of business, is established or is residing.

Alternative means of compliance to those adopted by the Agency may be used by an operator to establish compliance with Regulation (EC) No 216/2008 and its Implementing Rules.

(a)

Touring motor gliders shall be operated following the requirements for:

(1)

aeroplanes when they are power-driven by an engine; and

(2)

sailplanes when operated without using an engine.

(b)

Touring motor gliders shall be equipped in compliance with the requirements applicable to aeroplanes unless otherwise specified in Subpart D.

(c)

Powered sailplanes, excluding touring motor gliders, shall be operated and equipped in compliance with the requirements applicable to sailplanes.

(d)

Mixed balloons shall be operated in accordance with the requirements for hot-air balloons.

Introductory flights referred to in Article 6(4a)(c) of this Regulation, when conducted in accordance with this Annex, shall:

(a)

start and end at the same aerodrome or operating site;

(b)

be operated under VFR by day;

(c)

be overseen by a nominated person responsible for their safety; and

(d)

comply with any other conditions stipulated by the competent authority.

(a)

An NCO operator may use other than complex motor-powered aircraft listed on an operator's AOC to conduct non-commercial operations in accordance with this Annex.

(b)

The NCO operator using the aircraft in accordance with point (a) shall establish a procedure:

(1)

clearly describing how operational control of the aircraft is transferred between the AOC holder and the NCO operator, as referred to in point ORO.GEN.310 of Annex III;

(2)

describing the handover procedure of the aircraft upon its return to the AOC holder.

That procedure shall be included in a contract between the AOC holder and the NCO operator.

The NCO operator shall ensure that the procedure is communicated to the relevant personnel.

(c)

The continuing airworthiness of the aircraft used pursuant to point (a) shall be managed by organisation responsible for the continuing airworthiness for the aircraft included in the AOC, in accordance with Regulation (EU) No 1321/2014.

(d)

The NCO operator using the aircraft in accordance with point (a) shall ensure the following:

(1)

that every flight conducted under its operational control is recorded in the aircraft technical log system;

(2)

that no changes to the aircraft systems or configuration are made;

(3)

that any defect or technical malfunction occurring while the aircraft is under its operational control is reported to the organisation referred to in point (c) immediately after the flight;

(4)

that the AOC holder receives a copy of any occurrence report related to the flights performed with the aircraft, completed in accordance with Regulation (EU) No 376/2014 and Regulation (EU) 2015/1018.

(a)

The pilot-in-command shall be responsible for:

(1)

the safety of the aircraft and of all crew members, passengers and cargo on board during aircraft operations as referred to in 1.c of Annex IV to Regulation (EC) No 216/2008;

(2)

the initiation, continuation, termination or diversion of a flight in the interest of safety;

(3)

ensuring that all operational procedures and checklists are complied with as referred to in 1.b of Annex IV to Regulation (EC) No 216/2008;

(4)

only commencing a flight if he/she is satisfied that all operational limitations referred to in 2.a.3 of Annex IV to Regulation (EC) No 216/2008 are complied with, as follows:

(i)

the aircraft is airworthy;

(ii)

the aircraft is duly registered;

(iii)

instruments and equipment required for the execution of that flight are installed in the aircraft and are operative, unless operation with inoperative equipment is permitted by the minimum equipment list (MEL) or equivalent document, if applicable, as provided for in points NCO.IDE.A.105 or NCO.IDE.H.105;

(iv)

the mass of the aircraft and the centre of gravity location are such that the flight can be conducted within limits prescribed in the airworthiness documentation;

(v)

all equipment, baggage and cargo are properly loaded and secured and an emergency evacuation remains possible; and

(vi)

the aircraft operating limitations as specified in the aircraft flight manual (AFM) will not be exceeded at any time during the flight; and

(vii)

any navigational database required for PBN is suitable and current;

(5)

not commencing a flight if he/she is incapacitated from performing duties by any cause such as injury, sickness, fatigue or the effects of any psychoactive substance;

(6)

not continuing a flight beyond the nearest weather-permissible aerodrome or operating site when his/her capacity to perform duties is significantly reduced from causes such as fatigue, sickness or lack of oxygen;

(7)

deciding on acceptance of the aircraft with unserviceabilities in accordance with the configuration deviation list (CDL) or minimum equipment list (MEL), as applicable; and

(8)

recording utilisation data and all known or suspected defects in the aircraft at the termination of the flight, or series of flights, in the aircraft technical log or journey log for the aircraft.

(b)

The pilot-in-command shall ensure that during critical phases of flight or whenever deemed necessary in the interest of safety, all crew members are seated at their assigned stations and do not perform any activities other than those required for the safe operation of the aircraft.

(c)

The pilot-in-command shall have the authority to refuse carriage of or disembark any person, baggage or cargo that may represent a potential hazard to the safety of the aircraft or its occupants.

(d)

The pilot-in-command shall, as soon as possible, report to the appropriate air traffic services (ATS) unit any hazardous weather or flight conditions encountered that are likely to affect the safety of other aircraft.

(e)

The pilot-in-command shall, in an emergency situation that requires immediate decision and action, take any action he/she considers necessary under the circumstances in accordance with 7.d of Annex IV to Regulation (EC) No 216/2008. In such cases he/she may deviate from rules, operational procedures and methods in the interest of safety.

(f)

During flight, the pilot-in-command shall:

(1)

keep his/her safety belt fastened while at his/her station; and

(2)

remain at the controls of the aircraft at all times except if another pilot is taking the controls.

(g)

The pilot-in-command shall submit a report of an act of unlawful interference without delay to the competent authority and shall inform the designated local authority.

(h)

The pilot-in-command shall notify the nearest appropriate authority by the quickest available means of any accident involving the aircraft that results in serious injury or death of any person or substantial damage to the aircraft or property.

The pilot-in-command of a balloon shall in addition to NCO.GEN.105:

(a)

be responsible for the pre-flight briefing of those persons assisting in the inflation and deflation of the envelope;

(b)

ensure that no person is smoking on board or within the direct vicinity of the balloon; and

(c)

ensure that persons assisting in the inflation and deflation of the envelope wear appropriate protective clothing.

(a)

The pilot-in-command shall comply with the laws, regulations and procedures of those States where operations are conducted.

(b)

The pilot-in-command shall be familiar with the laws, regulations and procedures, pertinent to the performance of his/her duties, prescribed for the areas to be traversed, the aerodromes or operating sites to be used and the related air navigation facilities as referred to in 1.a of Annex IV to Regulation (EC) No 216/2008.

An aeroplane or a gyroplane shall only be taxied on the movement area of an aerodrome if the person at the controls:

(a)

is an appropriately qualified pilot; or

(b)

has been designated by the operator and:

(1)

is trained to taxi the aeroplane or the gyroplane;

(2)

is trained to use the radio telephone, if radio communications are required;

(3)

has received instruction in respect of aerodrome layout, routes, signs, marking, lights, air traffic control (ATC) signals and instructions, phraseology and procedures; and

(4)

is able to conform to the operational standards required for safe aeroplane or gyroplane movement at the aerodrome.

A helicopter rotor shall only be turned under power for the purpose of flight with a qualified pilot at the controls.

The pilot-in-command shall not permit any person to use a portable electronic device (PED) on board an aircraft, including an electronic flight bag (EFB), that could adversely affect the performance of the aircraft systems and equipment or the ability of the flight crew member to operate the aircraft.

Except for aircraft taking-off and landing at the same aerodrome/operating site, the operator shall, at all times, have available for immediate communication to rescue coordination centres (RCCs) lists containing information on the emergency and survival equipment carried on board.

(a)

The following documents, manuals and information shall be carried on each flight as originals or copies unless otherwise specified:

(1)

the AFM, or equivalent document(s);

(2)

the original certificate of registration;

(3)

the original certificate of airworthiness (CofA);

(4)

the noise certificate, if applicable;

(5)

the list of specific approvals, if applicable;

(6)

the aircraft radio licence, if applicable;

(7)

the third party liability insurance certificate(s);

(8)

the journey log, or equivalent, for the aircraft;

(9)

details of the filed ATS flight plan, if applicable;

(10)

current and suitable aeronautical charts for the routearea of the proposed flight and all routes along which it is reasonable to expect that the flight may be diverted;

(11)

procedures and visual signals information for use by intercepting and intercepted aircraft;

(12)

the MEL or CDL, if applicable; and

(13)

any other documentation that may be pertinent to the flight or is required by the States concerned with the flight.

(b)

Notwithstanding (a), on flights:

(1)

intending to take off and land at the same aerodrome/operating site; or

(2)

remaining within a distance or area determined by the competent authority,

the documents and information in (a)(2) to (a)(8) may be retained at the aerodrome or operating site.

(c)

Notwithstanding point (a), on flights with sailplanes, excluding touring motor gliders (TMGs), the documents and information referred to in points (a)(2) to (a)(8) and points (a)(11), (a)(12) and (a)(13) may be carried in the retrieve vehicle.

(d)

The pilot-in-command shall make available within a reasonable time of being requested to do so by the competent authority, the documentation required to be carried on board.

(a)

The transport of dangerous goods by air shall be conducted in accordance with Annex 18 to the Chicago Convention as last amended and amplified by the Technical Instructions for the Safe Transport of Dangerous Goods by Air (ICAO Doc 9284-AN/905), including its supplements and any other addenda or corrigenda.

(b)

Dangerous goods shall only be transported by the operator approved in accordance with Annex V (Part-SPA), Subpart G, to Regulation (EU) No 965/2012 except when:

(1)

they are not subject to the Technical Instructions in accordance with Part 1 of those Instructions; or

(2)

they are carried by passengers or the pilot-in-command, or are in baggage, in accordance with Part 8 of the Technical Instructions;

(3)

they are carried by operators of ELA2 aircraft.

(c)

The pilot-in-command shall take all reasonable measures to prevent dangerous goods from being carried on board inadvertently.

(d)

The pilot-in-command shall, in accordance with the Technical Instructions, report without delay to the competent authority and the appropriate authority of the State of occurrence in the event of any dangerous goods accidents or incidents.

(e)

The pilot-in-command shall ensure that passengers are provided with information about dangerous goods in accordance with the Technical Instructions.

(f)

Reasonable quantities of articles and substances that would otherwise be classified as dangerous goods and that are used to facilitate flight safety, where carriage aboard the aircraft is advisable to ensure their timely availability for operational purposes, shall be considered authorised under paragraph 1;2.2.1(a) of the Technical Instructions. This is regardless of whether or not such articles and substances are required to be carried or intended to be used in connection with a particular flight.

The packing and loading on board of the above-mentioned articles and substances shall be performed, under the responsibility of the pilot in command, in such a way as to minimise the risks posed to crew members, passengers, cargo or the aircraft during aircraft operations.

The operator shall implement:

(a)

any safety measures mandated by the competent authority in accordance with ARO.GEN.135(c); and

(b)

any relevant mandatory safety information issued by the Agency, including airworthiness directives.

Particulars of the aircraft, its crew and each journey shall be retained for each flight, or series of flights, in the form of a journey log, or equivalent.

(a)

An MEL may be established taking into account the following:

(1)

the document shall provide for the operation of the aircraft, under specified conditions, with particular instruments, items of equipment or functions inoperative at the commencement of the flight;

(2)

the document shall be prepared for each individual aircraft, taking account of the operator’s relevant operational and maintenance conditions; and

(3)

the MEL shall be based on the relevant Master Minimum Equipment List (MMEL), as defined in the data established in accordance with Commission Regulation (EU) No 748/2012 [OJ L 224, 21.8.2012, p. 1.], and shall not be less restrictive than the MMEL.

(b)

The MEL and any amendment thereto shall be notified to the competent authority.

The pilot-in-command shall only use aerodromes and operating sites that are adequate for the type of aircraft and operation concerned.

(a)

The pilot-in-command shall check the proper operation of the altimeter before each departure.

(b)

The pilot-in-command shall use appropriate altimeter settings for all phases of flight, taking into account any procedure prescribed by the State of the aerodrome or the State of the airspace.

For the selection of alternate aerodromes and the fuel/energy supply, the pilot-in-command shall not consider an aerodrome as an isolated aerodrome unless the flying time to the nearest weather-permissible destination alternate aerodrome is more than:

(a)

for aeroplanes with reciprocating engines, 60 minutes; or

(b)

for turbine-engined aeroplanes, 90 minutes.

(a)

For instrument flight rules (IFR) flights, the pilot-in-command shall establish aerodrome operating minima for each departure, destination or alternate aerodrome that is planned to be used in order to ensure separation of the aircraft from terrain and obstacles and to mitigate the risk of loss of visual references during the visual flight segment of instrument approach operations.

(b)

The aerodrome operating minima shall take the following elements into account, if relevant:

(1)

the type, performance, and handling characteristics of the aircraft;

(2)

the equipment available on the aircraft for the purpose of navigation, acquisition of visual references, and/or control of the flight path during take-off, approach, landing, and missed approach;

(3)

any conditions or limitations stated in the aircraft flight manual (AFM);

(4)

the dimensions and characteristics of the runways/final approach and take-off areas (FATOs) that may be selected for use;

(5)

the adequacy and performance of the available visual and non-visual aids and infrastructure;

(6)

the obstacle clearance altitude/height (OCA/H) for the instrument approach procedures (IAPs), if established;

(7)

the obstacles in the climb-out areas and clearance margins;

(8)

the competence and relevant operational experience of the pilot-in-command;

(9)

the IAP, if established;

(10)

the aerodrome characteristics and the type of air navigation services (ANS) available, if any;

(11)

any minima that may be promulgated by the State of the aerodrome;

(12)

the conditions prescribed in any specific approvals for low-visibility operations (LVOs) or operations with operational credits.

(a)

The decision height (DH) to be used for a 3D approach operation or a 2D approach operation flown with the continuous descent final approach (CDFA) technique shall not be lower than the highest of:

(1)

the obstacle clearance height (OCH) for the category of aircraft;

(2)

the published approach procedure DH or minimum descent height (MDH), where applicable;

(3)

the system minimum specified in Table 1;

(4)

the minimum DH specified in the AFM or equivalent document, if stated.

(b)

The MDH for a 2D approach operation flown without the CDFA technique shall not be lower than the highest of:

(1)

the OCH for the category of aircraft;

(2)

the published approach procedure MDH, where applicable;

(3)

the system minimum specified in Table 1; or

(4)

the minimum MDH specified in the AFM, if stated.

Facility | Lowest DH/MDH (ft)

ILS/MLS/ GLS | 200

GNSS/SBAS (LPV) | 200

Precision approach radar (PAR) | 200

GNSS/SBAS (LP) | 250

GNSS (LNAV) | 250

GNSS/Baro-VNAV (LNAV/VNAV) | 250

Helicopter point-in-space approach | 250

LOC with or without DME | 250

SRA (terminating at ½ NM) | 250

SRA (terminating at 1 NM) | 300

SRA (terminating at 2 NM or more) | 350

VOR | 300

VOR/DME | 250

NDB | 350

NDB/DME | 300

VDF | 350

(a)

The MDH for a circling approach operation with aeroplanes shall not be lower than the highest of:

(1)

the published circling OCH for the aeroplane category;

(2)

the minimum circling height derived from Table 1; or

(3)

the DH/MDH of the preceding IAP.

(b)

The minimum visibility for a circling approach operation with aeroplanes shall be the highest of:

(1)

the circling visibility for the aeroplane category, if published; or

(2)

the minimum visibility derived from Table 1’.

Aeroplane category

A | B | C | D

MDH (ft) | 400 | 500 | 600 | 700

Minimum VIS (m) | 1500 | 1500 | 2400 | 3600

The MDH for an onshore circling operation with helicopters shall not be lower than 250 ft and the meteorological visibility not less than 800 m.

(a)

The pilot-in-command shall use the departure and approach procedures established by the State of the aerodrome, if such procedures have been published for the runway or FATO to be used.

(b)

The pilot-in-command may deviate from a published departure route, arrival route or approach procedure:

(1)

provided obstacle clearance criteria can be observed, full account is taken of the operating conditions and any ATC clearance is adhered to; or

(2)

when being radar-vectored by an ATC unit.

The pilot-in-command shall ensure that, when PBN is required for the route or procedure to be flown:

(a)

the relevant PBN navigation specification is stated in the AFM or other document that has been approved by the certifying authority as part of an airworthiness assessment or is based on such approval; and

(b)

the aircraft is operated in conformance with the relevant navigation specification and limitations in the AFM or other document mentioned above.

The pilot-in-command shall take into account published noise abatement procedures to minimise the effect of aircraft noise while ensuring that safety has priority over noise abatement.

The pilot-in-command shall take into account operating procedures to minimise the effect of heating-system noise while ensuring that safety has priority over noise abatement.

(a)

The pilot-in-command shall ensure that the quantity of fuel/energy and oil that is carried on board is sufficient, taking into account the meteorological conditions, any element affecting the performance of the aircraft, any delays that are expected in flight, and any contingencies that may reasonably be expected to affect the flight.

(b)

The pilot-in-command shall plan a quantity of fuel/energy to be protected as final reserve fuel/energy to ensure a safe landing. The pilot-in-command shall take into account all of the following, and in the following order of priority, to determine the quantity of the final reserve fuel/energy:

(1)

the severity of the hazard to persons or property that may result from an emergency landing after fuel/energy starvation; and

(2)

the likelihood of unexpected circumstances that the final reserve fuel/energy may no longer be protected.

(c)

The pilot-in-command shall commence a flight only if the aircraft carries sufficient fuel/energy and oil:

(1)

when no destination alternate is required, to fly to the aerodrome or operating site of intended landing, plus the final reserve fuel/energy; or

(2)

when a destination alternate is required, to fly to the aerodrome or operating site of intended landing, and thereafter, to an alternate aerodrome, plus the final reserve fuel/energy.

(a)

The pilot-in-command shall only commence a flight if the helicopter carries sufficient fuel and oil for the following:

(1)

for VFR flights, to fly to the aerodrome/operating site of intended landing and thereafter to fly for at least 20 minutes at best-range-speed; and

(2)

for IFR flights:

(i)

when no alternate is required or no weather-permissible alternate aerodrome is available, to fly to the aerodrome/operating site of intended landing, and thereafter to fly for 30 minutes at holding speed at 450 m (1500 ft) above the destination aerodrome/operating site under standard temperature conditions and approach and land; or

(ii)

when an alternate is required, to fly to and execute an approach and a missed approach at the aerodrome/operating site of intended landing, and thereafter:

(A) to fly to the specified alternate; and

(B) to fly for 30 minutes at holding speed at 450 m (1500 ft) above the alternate aerodrome/operating site under standard temperature conditions and approach and land.

(b)

In computing the fuel required including to provide for contingency, the following shall be taken into consideration:

(1)

forecast meteorological conditions;

(2)

anticipated ATC routings and traffic delays;

(3)

procedures for loss of pressurisation or failure of one engine while en-route, where applicable; and

(4)

any other condition that may delay the landing of the aircraft or increase fuel and/or oil consumption.

(c)

Nothing shall preclude amendment of a flight plan in-flight, in order to re-plan the flight to another destination, provided that all requirements can be complied with from the point where the flight is re-planned.

This article is long: the rest is at the official publication.