The competent authority shall be the authority designated by the Member State in which the operator has its principal place of business, is established or is residing.
The crew member shall be responsible for the proper execution of his/her duties that are:
related to the safety of the aircraft and its occupants; and
specified in the instructions and procedures in the operations manual.
During critical phases of flight or whenever deemed necessary by the pilot-in-command in the interest of safety, the crew member shall be seated at his/her assigned station and shall not perform any activities other than those required for the safe operation of the aircraft.
During flight, the flight crew member shall keep his/her safety belt fastened while at his/her station.
During flight, at least one qualified flight crew member shall remain at the controls of the aircraft at all times.
The crew member shall not undertake duties on an aircraft:
if he/she knows or suspects that he/she is suffering from fatigue as referred to in 7.f of Annex IV to Regulation (EC) No 216/2008 or feels otherwise unfit, to the extent that the flight may be endangered; or
when under the influence of psychoactive substances or for other reasons as referred to in 7.g of Annex IV to Regulation (EC) No 216/2008.
The crew member who undertakes duties for more than one operator shall:
maintain his/her individual records regarding flight and duty times and rest periods as referred to in Annex III (Part-ORO), Subpart FTL to Regulation (EU) No 965/2012; and
provide each operator with the data needed to schedule activities in accordance with the applicable FTL requirements.
The crew member shall report to the pilot-in-command:
any fault, failure, malfunction or defect, which he/she believes may affect the airworthiness or safe operation of the aircraft, including emergency systems; and
any incident that was endangering, or could endanger, the safety of the operation.
Approved training organisations that are required to comply with this Annex shall also comply with:
ORO.GEN.310, as applicable; and
ORO.MLR.105.
The pilot-in-command shall be responsible for:
the safety of the aircraft and of all crew members, passengers and cargo on board during aircraft operations as referred to in 1.c of Annex IV to Regulation (EC) No 216/2008;
the initiation, continuation, termination or diversion of a flight in the interest of safety;
ensuring that all instructions, operational procedures and checklists are complied with in accordance with the operations manual and as referred to in 1.b of Annex IV to Regulation (EC) No 216/2008;
only commencing a flight if he/she is satisfied that all operational limitations referred to in 2.a.3 of Annex IV to Regulation (EC) No 216/2008 are complied with, as follows:
the aircraft is airworthy;
the aircraft is duly registered;
instruments and equipment required for the execution of that flight are installed in the aircraft and are operative, unless operation with inoperative equipment is permitted by the minimum equipment list (MEL) or equivalent document, as required in NCC.IDE.A.105 or NCC.IDE.H.105;
the mass of the aircraft and centre of gravity location are such that the flight can be conducted within the limits prescribed in the airworthiness documentation;
all cabin baggage, hold luggage and cargo are properly loaded and secured;
the aircraft operating limitations as specified in the aircraft flight manual (AFM) will not be exceeded at any time during the flight;
each flight crew member holds a valid licence in accordance with Regulation (EU) No 1178/2011; and
flight crew members are properly rated and meet competency and recency requirements; and
any navigational database required for performance-based navigation is suitable and current;
not commencing a flight if any flight crew member is incapacitated from performing duties by any cause such as injury, sickness, fatigue or the effects of any psychoactive substance;
not continuing a flight beyond the nearest weather-permissible aerodrome or operating site, when the capacity of any flight crew member to perform duties is significantly reduced from causes such as fatigue, sickness or lack of oxygen;
deciding on acceptance of the aircraft with unserviceabilities in accordance with the configuration deviation list (CDL) or minimum equipment list (MEL), as applicable;
recording utilisation data and all known or suspected defects in the aircraft at the termination of the flight, or series of flights, in the aircraft technical log or journey log for the aircraft; and
ensuring that:
flight recorders are not disabled or switched off during flight;
in the event of an occurrence other than an accident or a serious incident that shall be reported according to ORO.GEN.160(a), flight recorders' recordings are not intentionally erased; and
in the event of an accident or a serious incident, or if preservation of recordings of flight recorders is directed by the investigating authority:
(A) flight recorders' recordings are not intentionally erased;
(B) flight recorders are deactivated immediately after the flight is completed; and
(C) precautionary measures to preserve the recordings of flight recorders are taken before leaving the flight crew compartment.
The pilot-in-command shall have the authority to refuse carriage of or disembark any person, baggage or cargo that may represent a potential hazard to the safety of the aircraft or its occupants.
The pilot-in-command shall, as soon as possible, report to the appropriate air traffic services (ATS) unit any hazardous weather or flight conditions encountered that are likely to affect the safety of other aircraft.
Notwithstanding the provision of (a)(6), in a multi-crew operation the pilot-in-command may continue a flight beyond the nearest weather-permissible aerodrome when adequate mitigating procedures are in place.
The pilot-in-command shall, in an emergency situation that requires immediate decision and action, take any action he/she considers necessary under the circumstances in accordance with 7.d of Annex IV to Regulation (EC) No 216/2008. In such cases he/she may deviate from rules, operational procedures and methods in the interest of safety.
The pilot-in-command shall submit a report of an act of unlawful interference without delay to the competent authority and shall inform the designated local authority.
The pilot-in-command shall notify the nearest appropriate authority by the quickest available means of any accident involving the aircraft that results in serious injury or death of any person or substantial damage to the aircraft or property.
The pilot-in-command shall comply with the laws, regulations and procedures of those States where operations are conducted.
The pilot-in-command shall be familiar with the laws, regulations and procedures, pertinent to the performance of his/her duties, prescribed for the areas to be traversed, the aerodromes or operating sites to be used and the related air navigation facilities as referred to in 1.a of Annex IV to Regulation (EC) No 216/2008.
The operator shall ensure that all crew members can communicate with each other in a common language.
The operator shall establish procedures for taxiing to ensure safe operation and to enhance runway safety.
The operator shall ensure that an aeroplane is only taxied on the movement area of an aerodrome if the person at the controls:
is an appropriately qualified pilot; or
has been designated by the operator and:
is trained to taxi the aeroplane;
is trained to use the radio telephone, if radio communications are required;
has received instruction in respect of aerodrome layout, routes, signs, marking, lights, air traffic control (ATC) signals and instructions, phraseology and procedures; and
is able to conform to the operational standards required for safe aeroplane movement at the aerodrome.
A helicopter rotor shall only be turned under power for the purpose of flight with a qualified pilot at the controls.
The operator shall not permit any person to use a portable electronic device (PED) on board an aircraft that could adversely affect the performance of the aircraft’s systems and equipment.
Where an EFB is used on board an aircraft, the operator shall ensure that it does not adversely affect the performance of the aircraft systems or equipment, or the ability of the flight crew member to operate the aircraft.
Prior to using a type B EFB application, the operator shall:
conduct a risk assessment related to the use of the EFB device that hosts the application and to the EFB application concerned and its associated function(s), identifying the associated risks and ensuring that they are appropriately managed and mitigated; the risk assessment shall address the risks associated with the human–machine interface of the EFB device and the EFB application concerned; and
establish an EFB administration system, including procedures and training requirements for the administration and use of the device and the EFB application.
The operator shall at all times have available for immediate communication to rescue coordination centres (RCCs) lists containing information on the emergency and survival equipment carried on board.
The following documents, manuals and information shall be carried on each flight as originals or copies unless otherwise specified:
the AFM, or equivalent document(s);
the original certificate of registration;
the original certificate of airworthiness (CofA);
the noise certificate;
the declaration as specified in Annex III (Part-ORO), ORO.DEC.100, to Regulation (EU) No 965/2012;
the list of specific approvals, if applicable;
the aircraft radio licence, if applicable;
the third party liability insurance certificate(s);
the journey log, or equivalent, for the aircraft;
details of the filed ATS flight plan, if applicable;
current and suitable aeronautical charts for the route of the proposed flight and all routes along which it is reasonable to expect that the flight may be diverted;
procedures and visual signals information for use by intercepting and intercepted aircraft;
information concerning search and rescue services for the area of the intended flight;
the current parts of the operations manual that are relevant to the duties of the crew members, which shall be easily accessible to the crew members;
the MEL or CDL;
appropriate notices to airmen (NOTAMs) and aeronautical information service (AIS) briefing documentation;
appropriate meteorological information;
cargo and/or passenger manifests, if applicable; and
any other documentation that may be pertinent to the flight or is required by the States concerned with the flight.
In case of loss or theft of documents specified in (a)(2) to (a)(8), the operation may continue until the flight reaches its destination or a place where replacement documents can be provided.
Following an accident, a serious incident or an occurrence identified by the investigating authority, the operator of an aircraft shall preserve the original recorded data of the flight recorders for a period of 60 days or until otherwise directed by the investigating authority.
The operator shall conduct operational checks and evaluations of recordings to ensure the continued serviceability of the flight recorders which are required to be carried.
The operator shall ensure that the recordings of flight parameters and data link communication messages required to be recorded on flight recorders are preserved. However, for the purpose of testing and maintaining those flight recorders, up to 1 hour of the oldest recorded data at the time of testing may be erased.
The operator shall keep and maintain up to date documentation that presents the necessary information to convert raw flight data into flight parameters expressed in engineering units.
The operator shall make available any flight recorder recordings that have been preserved, if so determined by the competent authority.
Without prejudice to Regulations (EU) No 996/2010 and (EU) 2016/679:
Except for ensuring flight recorder serviceability, audio recordings from a flight recorder shall not be disclosed or used unless all of the following conditions are fulfilled:
a procedure related to the handling of such audio recordings and of their transcript is in place;
all crew members and maintenance personnel concerned have given their prior consent;
such audio recordings are used only for maintaining or improving safety.
When flight recorder audio recordings are inspected for ensuring flight recorder serviceability, the operator shall protect the privacy of those audio recordings and make sure that they are not disclosed or used for purposes other than ensuring flight recorder serviceability.
Flight parameters or data link messages recorded by a flight recorder shall not be used for purposes other than for the investigation of an accident or an incident which is subject to mandatory reporting, unless such recordings meet any of the following conditions:
are used by the operator for airworthiness or maintenance purposes only;
are de-identified;
are disclosed under secure procedures.
Except for ensuring flight recorder serviceability, images of the flight crew compartment that are recorded by a flight recorder shall not be disclosed or used unless all the following conditions are fulfilled:
a procedure related to the handling of such image recordings is in place;
all crew members and maintenance personnel concerned have given their prior consent;
such image recordings are used only for maintaining or improving safety.
When images of the flight crew compartment that are recorded by a flight recorder are inspected for ensuring the serviceability of the flight recorder, then:
those images shall not be disclosed or used for purposes other than for ensuring flight recorder serviceability;
if body parts of crew members are likely to be visible on the images, the operator shall ensure the privacy of those images.
The transport of dangerous goods by air shall be conducted in accordance with Annex 18 to the Chicago Convention as last amended and amplified by the Technical Instructions for the Safe Transport of Dangerous Goods by Air (ICAO Doc 9284-AN/905), including its supplements and any other addenda or corrigenda.
Dangerous goods shall only be transported by the operator approved in accordance with Annex V (Part-SPA), Subpart G, to Regulation (EU) No 965/2012 except when:
they are not subject to the Technical Instructions in accordance with Part 1 of those Instructions; or
they are carried by passengers or crew members, or are in baggage, in accordance with Part 8 of the Technical Instructions.
The operator shall establish procedures to ensure that all reasonable measures are taken to prevent dangerous goods from being carried on board inadvertently.
The operator shall provide personnel with the necessary information enabling them to carry out their responsibilities, as required by the Technical Instructions.
The operator shall, in accordance with the Technical Instructions, report without delay to the competent authority and the appropriate authority of the State of occurrence in the event of any dangerous goods accidents or incidents.
The operator shall ensure that passengers are provided with information about dangerous goods in accordance with the Technical Instructions.
The operator shall ensure that notices giving information about the transport of dangerous goods are provided at acceptance points for cargo as required by the Technical Instructions.
The operator shall only use aerodromes and operating sites that are adequate for the type of aircraft and operation concerned.
The operator shall establish procedures for altimeter checking before each departure.
The operator shall establish procedures for altimeter settings for all phases of flight, which shall take into account the procedures established by the State of the aerodrome or the State of the airspace, if applicable.
For the selection of alternate aerodromes and the fuel/energy planning and in-flight re-planning policy, the operator shall not consider an aerodrome as an isolated aerodrome unless the flying time to the nearest weather-permissible destination alternate aerodrome is more than:
for aeroplanes with reciprocating engines, 60 minutes; or
for turbine-engined aeroplanes, 90 minutes.
The operator shall establish aerodrome operating minima for each departure, destination or alternate aerodrome that is planned to be used in order to ensure separation of the aircraft from terrain and obstacles and to mitigate the risk of loss of visual references during the visual flight segment of instrument approach operations.
The method used to establish aerodrome operating minima shall take all the following elements into account:
the type, performance, and handling characteristics of the aircraft;
the equipment available on the aircraft for the purpose of navigation, acquisition of visual references, and/or control of the flight path during take-off, approach, landing, and missed approach;
any conditions or limitations stated in the aircraft flight manual (AFM);
the dimensions and characteristics of the runways/final approach and take-off areas (FATOs) that may be selected for use;
the adequacy and performance of the available visual and non-visual aids and infrastructure;
the obstacle clearance altitude/height (OCA/H) for the instrument approach procedures (IAPs);
the obstacles in the climb-out areas and necessary clearance margins;
any non-standard characteristics of the aerodrome, the IAP or the environment;
the composition of the flight crew, their competence and experience;
the IAP;
the aerodrome characteristics and the available air navigation services (ANS);
any minima that may be promulgated by the State of the aerodrome;
the conditions prescribed in any specific approvals for low-visibility operations (LVOs) or operations with operational credits; and
the relevant operational experience of the operator.
The operator shall specify a method of determining aerodrome operating minima in the operations manual.
The decision height (DH) to be used for a non-precision approach (NPA) flown with the continuous descent final approach (CDFA) technique, approach procedure with vertical guidance (APV) or category I (CAT I) operation shall not be lower than the highest of:
the minimum height to which the approach aid can be used without the required visual reference;
the obstacle clearance height (OCH) for the category of aircraft;
the published approach procedure DH where applicable;
the system minimum specified in Table 1; or
the minimum DH specified in the AFM or equivalent document, if stated.
The minimum descent height (MDH) for an NPA operation flown without the CDFA technique shall not be lower than the highest of:
the OCH for the category of aircraft;
the system minimum specified in Table 1; or
the minimum MDH specified in the AFM, if stated.
Facility | Lowest DH/MDH (ft)
Instrument landing system (ILS) | 200
Global navigation satellite system (GNSS)/Satellite-based augmentation system (SBAS) (Lateral precision with vertical guidance approach (LPV)) | 200
GNSS (Lateral Navigation (LNAV)) | 250
GNSS/Baro-vertical navigation (VNAV) (LNAV/VNAV) | 250
Localiser (LOC) with or without distance measuring equipment (DME) | 250
Surveillance radar approach (SRA) (terminating at ½ NM) | 250
SRA (terminating at 1 NM) | 300
SRA (terminating at 2 NM or more) | 350
VHF omnidirectional radio range (VOR) | 300
VOR/DME | 250
Non-directional beacon (NDB) | 350
NDB/DME | 300
VHF direction finder (VDF) | 350
The MDH for a circling approach operation with aeroplanes shall not be lower than the highest of:
the published circling OCH for the aeroplane category;
the minimum circling height derived from Table 1; or
the DH/MDH of the preceding IAP.
The minimum visibility for a circling approach operation with aeroplanes shall be the highest of:
the circling visibility for the aeroplane category, if published; or
the minimum visibility derived from Table 1.
Aeroplane category
A | B | C | D
MDH (ft) | 400 | 500 | 600 | 700
Minimum VIS (m) | 1500 | 1600 | 2400 | 3600
The MDH for an onshore circling operation with helicopters shall not be lower than 250 ft and the meteorological visibility not less than 800 m.
The pilot-in-command shall use the departure and approach procedures established by the State of the aerodrome, if such procedures have been published for the runway or FATO to be used.
Notwithstanding (a), the pilot-in-command shall only accept an ATC clearance to deviate from a published procedure:
provided that obstacle clearance criteria are observed and full account is taken of the operating conditions; or
when being radar-vectored by an ATC unit.
In any case, the final approach segment shall be flown visually or in accordance with the published approach procedures.
The operator shall ensure that, when PBN is required for the route or procedure to be flown:
the relevant PBN specification is stated in the AFM or other document that has been approved by the certifying authority as part of an airworthiness assessment or is based on such approval; and
the aircraft is operated in conformance with the relevant navigation specification and limitations in the AFM or other document mentioned above.
The operator shall develop operating procedures taking into account the need to minimise the effect of aircraft noise while ensuring that safety has priority over noise abatement.
The operator shall specify a method to establish minimum flight altitudes that provide the required terrain clearance for all route segments to be flown in IFR.
The pilot-in-command shall establish minimum flight altitudes for each flight based on this method. The minimum flight altitudes shall not be lower than that published by the State overflown.
The operator shall establish, implement, and maintain a fuel/energy scheme that comprises:
a fuel/energy planning and in-flight re-planning policy; and
an in-flight fuel/energy management policy.
The fuel/energy scheme shall:
be appropriate for the type(s) of operation performed; and
correspond to the capability of the operator to support its implementation.