ANNEX V, Commission Regulation (EU) No 965/2012 of 5 October 2012 laying down technical requireme…

In forcesince 25 May 2026cited 13×
(a)

The competent authority for the issuing of a specific approval shall be:

(1)

for a commercial operator of aeroplanes or helicopters, the authority of the Member State where the operator has its principal place of business;

(2)

for a non-commercial operator of aeroplanes or helicopters, the authority of the Member State where the operator has its principal place of business, is established or resides;

(3)

for an IAM operator of VTOL-capable aircraft (VCA), the authority of the Member State where the operator has its principal place of business or resides.

(b)

Notwithstanding point (a)(2), for a non-commercial operator that uses an aeroplane or a helicopter registered in a third country, the applicable requirements under this Annex for the approval of the following operations shall not apply if that approval is issued by a third-country State of Registry:

(1)

performance-based navigation (PBN);

(2)

minimum navigation performance specifications (MNPS);

(3)

reduced vertical separation minima (RVSM) airspace;

(4)

low-visibility operations (LVOs).

(a)

The operator applying for the initial issue of a specific approval shall provide to the competent authority the documentation required in the applicable Subpart, together with the following information:

(1)

the name, address and mailing address of the applicant;

(2)

a description of the intended operation.

(b)

The operator shall provide the following evidence to the competent authority:

(1)

compliance with the requirements of the applicable Subpart;

(2)

that the relevant elements defined in the mandatory part of the operational suitability data established in accordance with Regulation (EU) No 748/2012 are taken into account.

(c)

The operator shall retain records relating to (a) and (b) at least for the duration of the operation requiring a specific approval, or, if applicable, in accordance with Annex III (Part-ORO).

The scope of the activity that an operator is approved to conduct shall be documented and specified:

(a)

for operators holding an air operator certificate (AOC) in the operations specifications to the AOC;

(b)

for all other operators in the list of specific approvals.

When the conditions of a specific approval are affected by changes, the operator shall provide the relevant documentation to the competent authority and obtain prior approval for the operation.

Specific approvals shall be issued for an unlimited duration and shall remain valid subject to the operator remaining in compliance with the requirements associated with the specific approval and taking into account the relevant elements defined in the mandatory part of the operational suitability data established in accordance with Regulation (EU) No 748/2012.

(a)

An approval is required for each of the following PBN specifications:

(1)

RNP AR APCH; and

(2)

RNP 0.3 for helicopter operation.

(b)

An approval for RNP AR APCH operations shall allow operations on public instrument approach procedures which meet the applicable ICAO procedure design criteria.

(c)

A procedure-specific approval for RNP AR APCH or RNP 0.3 shall be required for private instrument approach procedures or any public instrument approach procedure that does not meet the applicable ICAO procedure design criteria, or where required by the Aeronautical Information Publication (AIP) or the competent authority.

To obtain a PBN specific approval from the competent authority, the operator shall provide evidence that:

(a)

the relevant airworthiness approval, suitable for the intended PBN operation, is stated in the AFM or other document that has been approved by the certifying authority as part of an airworthiness assessment or is based on such approval;

(b)

a training programme for the flight crew members and relevant personnel involved in the flight preparation has been established;

(c)

a safety assessment has been carried out;

(d)

operating procedures have been established specifying:

(1)

the equipment to be carried, including its operating limitations and appropriate entries in the minimum equipment list (MEL);

(2)

flight crew composition, qualification and experience;

(3)

normal, abnormal and contingency procedures; and

(4)

electronic navigation data management.

(e)

a list of reportable events has been specified; and

(f)

a management RNP monitoring programme has been established for RNP AR APCH operations, if applicable.

Aeroplanes and helicopters shall only be operated in designated minimum navigation performance specifications (MNPS) airspace in accordance with regional supplementary procedures, where MNPS are established, if the operator has been granted an approval by the competent authority to conduct such operations.

To obtain an MNPS operational approval from the competent authority, the operator shall provide evidence that:

(a)

the navigation equipment meets the required performance;

(b)

navigation displays, indicators and controls are visible and operable by either pilot seated at his/her duty station;

(c)

a training programme for the flight crew members involved in these operations has been established;

(d)

operating procedures have been established specifying:

(1)

the equipment to be carried, including its operating limitations and appropriate entries in the MEL;

(2)

flight crew composition and experience requirements;

(3)

normal procedures;

(4)

contingency procedures including those specified by the authority responsible for the airspace concerned;

(5)

monitoring and incident reporting.

Aeroplanes and helicopters shall only be operated in designated airspace where a reduced vertical separation minimum of 300 m (1000 ft) applies between flight level (FL) 290 and FL 410, inclusive, if the operator has been granted an approval by the competent authority to conduct such operations.

To obtain an RVSM operational approval from the competent authority, the operator shall provide evidence that:

(a)

the RVSM airworthiness approval has been obtained;

(b)

procedures for monitoring and reporting height-keeping errors have been established;

(c)

a training programme for the flight crew members involved in these operations has been established;

(d)

operating procedures have been established specifying:

(1)

the equipment to be carried, including its operating limitations and appropriate entries in the MEL;

(2)

flight crew composition and experience requirements;

(3)

flight planning;

(4)

pre-flight procedures;

(5)

procedures prior to RVSM airspace entry;

(6)

in-flight procedures;

(7)

post-flight procedures;

(8)

incident reporting;

(9)

specific regional operating procedures.

Aircraft used for operations in RVSM airspace shall be equipped with:

(a)

two independent altitude measurement systems;

(b)

an altitude alerting system;

(c)

an automatic altitude control system;

(d)

a secondary surveillance radar (SSR) transponder with altitude reporting system that can be connected to the altitude measurement system in use for altitude control.

(a)

The operator shall report recorded or communicated occurrences of height-keeping errors caused by malfunction of aircraft equipment or of operational nature, equal to or greater than:

(1)

a total vertical error (TVE) of ± 90 m (± 300 ft);

(2)

an altimetry system error (ASE) of ± 75 m (± 245 ft); and

(3)

an assigned altitude deviation (AAD) of ± 90 m (± 300 ft).

(b)

Reports of such occurrences shall be sent to the competent authority within 72 hours. Reports shall include an initial analysis of causal factors and measures taken to prevent repeat occurrences.

(c)

When height-keeping errors are recorded or received, the operator shall take immediate action to rectify the conditions that caused the errors and provide follow-up reports, if requested by the competent authority.

An operator of aeroplanes or helicopters shall conduct the following operations only if they are approved by the competent authority:

(a)

take-off operations with visibility conditions of less than 400 m RVR;

(b)

instrument approach operations in low-visibility conditions; and

(c)

operations with operational credits, except for EFVS 200 operations, which shall not be subject to a specific approval.

To obtain a specific approval as required by SPA.LVO.100, the operator shall demonstrate that:

(a)

for low-visibility approach operations, LVTO operations in an RVR less than 125 m, and operations with operational credits, the aircraft has been certified for the intended operations;

(b)

the flight crew members are competent to conduct the intended operation and a training and checking programme for the flight crew members and relevant personnel involved in the flight preparation has been established, in accordance with SPA.LVO.120;

(c)

operating procedures for the intended operations have been established;

(d)

any relevant changes to the minimum equipment list (MEL) have been made;

(e)

any relevant changes to the maintenance programme have been made;

(f)

procedures have been established to ensure the suitability of aerodromes, including instrument flight procedures, for the intended operations, in accordance with SPA.LVO.110; and

(g)

for the intended operations, a safety assessment has been carried out, and performance indicators have been established to monitor the level of safety.

The operator shall ensure that only aerodromes, including instrument flight procedures, suitable for the intended operations are used for LVOs and operations with operational credits.

(a)

The operator shall not use an aerodrome for LVOs below a visibility of 800 m unless:

(1)

the aerodrome has been approved for such operations by the State of the aerodrome; and

(2)

low visibility procedures (LVP) have been established.

(b)

If the operator selects an aerodrome where the term LVP is not used, the operator shall ensure that there are equivalent procedures that adhere to the requirements of LVP at the aerodrome. This situation shall be clearly noted in the operations manual or procedures manual including guidance to the flight crew on how to determine that the equivalent LVP are in effect.

(a)

The operator shall ensure that the flight crew is competent to conduct the intended operations.

(b)

The operator shall ensure that each flight crew member successfully completes training and checking for all types of LVOs and operations with operational credits for which an approval has been granted. Such training and checking shall:

(1)

include initial and recurrent training and checking;

(2)

include normal, abnormal and emergency procedures;

(3)

be tailored to the type of technologies used in the intended operations; and

(4)

take into account the human factor risks associated with the intended operations.

(c)

The operator shall keep records of the training and qualifications of the flight crew members.

(d)

The training and checking shall be conducted by appropriately qualified personnel. In the case of flight and flight simulation training and checking, the personnel providing the training and conducting the checks shall be qualified in accordance with Annex I (Part-FCL) to Regulation (EU) No 1178/2011.

(a)

The operator shall establish procedures and instructions to be used for LVOs. These procedures and instructions shall be included in the operations manual or procedures manual and contain the duties of flight crew members during taxiing, take-off, approach, flare, landing, rollout and missed approach operations, as appropriate.

(b)

Prior to commencing an LVO, the pilot-in-command/commander shall be satisfied that:

(1)

the status of the visual and non-visual facilities is sufficient;

(2)

appropriate LVPs are in force according to information received from air traffic services (ATS);

(3)

flight crew members are properly qualified.

(a)

The operator shall include the minimum equipment that has to be serviceable at the commencement of an LVO in accordance with the aircraft flight manual (AFM) or other approved document in the operations manual or procedures manual, as applicable.

(b)

The pilot-in-command/commander shall be satisfied that the status of the aircraft and of the relevant airborne systems is appropriate for the specific operation to be conducted.

In commercial air transport operations, two-engined aeroplanes shall only be operated beyond the threshold distance determined in accordance with CAT.OP.MPA.140 if the operator has been granted an ETOPS operational approval by the competent authority.

To obtain an ETOPS operational approval from the competent authority, the operator shall provide evidence that:

(a)

the aeroplane/engine combination holds an ETOPS type design and reliability approval for the intended operation;

(b)

a training programme for the flight crew members and all other operations personnel involved in these operations has been established and the flight crew members and all other operations personnel involved are suitably qualified to conduct the intended operation;

(c)

the operator’s organisation and experience are appropriate to support the intended operation;

(d)

operating procedures have been established.

(a)

An ETOPS en-route alternate aerodrome shall be considered adequate, if, at the expected time of use, the aerodrome is available and equipped with necessary ancillary services such as air traffic services (ATS), sufficient lighting, communications, weather reporting, navigation aids and emergency services and has at least one instrument approach procedure available.

(b)

Prior to conducting an ETOPS flight, the operator shall ensure that an ETOPS en-route alternate aerodrome is available, within either the operator’s approved diversion time, or a diversion time based on the MEL generated serviceability status of the aeroplane, whichever is shorter.

(c)

The operator shall specify any required ETOPS en-route alternate aerodrome(s) in the operational flight plan and ATS flight plan.

(a)

The operator shall only select an aerodrome as an ETOPS en-route alternate aerodrome when the appropriate weather reports or forecasts, or any combination thereof, indicate that, between the anticipated time of landing until one hour after the latest possible time of landing, conditions will exist at or above the planning minima calculated by adding the additional limits of Table 1.

(b)

The operator shall include in the operations manual the method for determining the operating minima at the planned ETOPS en-route alternate aerodrome.

[VIS: visibility; MDA/H: minimum descent altitude/height.]

Type of approach | Planning minima

Precision approach |

DA/H + 200 ft

RVR/VIS + 800 m

Non-precision approach or

Circling approach

MDA/H + 400 ft

RVR/VIS + 1500 m

Except as provided for in Annex IV (Part-CAT), Annex VI (Part-NCC), Annex VII (Part-NCO), Annex VIII (Part-SPO) and Annex IX (Part-IAM) to this Regulation, the operator shall only transport dangerous goods by air if it has been approved by the competent authority.

To obtain the approval to transport dangerous goods, the operator shall in accordance with the technical instructions:

(a)

establish and maintain a training programme for all personnel involved and demonstrate to the competent authority that adequate training has been given to all personnel;

(b)

establish operating procedures to ensure the safe handling of dangerous goods at all stages of air transport, containing information and instructions on:

(1)

the operator’s policy to transport dangerous goods;

(2)

the requirements for acceptance, handling, loading, stowage and segregation of dangerous goods;

(3)

actions to take in the event of an aircraft accident or incident when dangerous goods are being carried;

(4)

the response to emergency situations involving dangerous goods;

(5)

the removal of any possible contamination;

(6)

the duties of all personnel involved, especially with relevance to ground handling and aircraft handling;

(7)

inspection for damage, leakage or contamination;

(8)

dangerous goods accident and incident reporting.

The operator shall, in accordance with the technical instructions:

(a)

provide written information to the pilot-in-command/commander:

(1)

about dangerous goods to be carried on the aircraft;

(2)

for use in responding to in-flight emergencies;

(b)

use an acceptance checklist;

(c)

ensure that dangerous goods are accompanied by the required dangerous goods transport document(s), as completed by the person offering dangerous goods for air transport, except when the information applicable to the dangerous goods is provided in electronic form;

(d)

ensure that where a dangerous goods transport document is provided in written form, a copy of the document is retained on the ground where it will be possible to obtain access to it within a reasonable period until the goods have reached their final destination;

(e)

ensure that a copy of the information to the pilot-in-command or the commander is retained on the ground and that that copy, or the information contained in it, is readily accessible to the flight operations officer, flight dispatcher, or the designated ground personnel responsible for their part of the flight operations, until after the completion of the flight to which the information refers;

(f)

retain the acceptance checklist, transport document and information to the pilot-in-command/commander for at least three months after completion of the flight;

(g)

retain the training records of all personnel for at least three years.

(a)

Helicopters shall only be operated under VFR at night with the aid of NVIS if the operator has been approved by the competent authority.

(b)

To obtain such approval by the competent authority, the operator shall:

(1)

operate in commercial air transport (CAT) and hold a CAT AOC in accordance with Annex III (Part-ORO);

(2)

demonstrate to the competent authority:

(i)

compliance with the applicable requirements contained in this Subpart;

(ii)

the successful integration of all elements of the NVIS.

(a)

Before conducting NVIS operations each helicopter and all associated NVIS equipment shall have been issued with the relevant airworthiness approval in accordance withRegulation (EU) No 748/2012.

(b)

Radio altimeter. The helicopter shall be equipped with a radio altimeter capable of emitting an audio warning below a pre-set height and an audio and visual warning at a height selectable by the pilot, instantly discernible during all phases of NVIS flight.

(c)

Aircraft NVIS compatible lighting. To mitigate the reduced peripheral vision cues and the need to enhance situational awareness, the following shall be provided:

(1)

NVIS-compatible instrument panel flood-lighting, if installed, that can illuminate all essential flight instruments;

(2)

NVIS-compatible utility lights;

(3)

portable NVIS compatible flashlight; and

(4)

a means for removing or extinguishing internal NVIS non-compatible lights.

(d)

Additional NVIS equipment. The following additional NVIS equipment shall be provided:

(1)

a back-up or secondary power source for the night vision goggles (NVG);

(2)

a helmet with the appropriate NVG attachment.

(e)

All required NVG on an NVIS flight shall be of the same filter class and shall provide for sufficiently equivalent visual acuity.

(1)

Procedures for continuing airworthiness shall contain the information necessary for carrying out ongoing maintenance and inspections on NVIS equipment installed in the helicopter and shall cover, as a minimum:

(i)

helicopter windscreens and transparencies;

(ii)

NVIS lighting;

(iii)

NVGs; and

(iv)

any additional equipment that supports NVIS operations.

(2)

Any subsequent modification or maintenance to the aircraft shall be in compliance with the NVIS airworthiness approval.

(a)

Operations shall not be conducted below the weather minima for the type of night operations being conducted.

(b)

The operator shall establish the minimum transition height from where a change to/from aided flight may be continued.

(a)

Selection. The operator shall establish criteria for the selection of crew members for the NVIS task.

(b)

Experience. The minimum experience for the commander shall not be less than 20 hours VFR at night as pilot-in-command/commander of a helicopter before commencing training.

(c)

Operational training. All pilots shall have completed the operational training in accordance with the NVIS procedures contained in the operations manual.

(d)

Recency. All pilots and NVIS technical crew members conducting NVIS operations shall have completed three NVIS flights in the last 90 days. Recency may be re-established on a training flight in the helicopter or an approved full flight simulator (FFS), which shall include the elements of (f)(1).

(e)

Crew composition. The minimum crew shall be the greater of that specified:

(1)

in the aircraft flight manual (AFM);

(2)

for the underlying activity; or

(3)

in the operational approval for the NVIS operations.

(1)

Training and checking shall be conducted in accordance with a detailed syllabus approved by the competent authority and included in the operations manual.

(i)

Crew training programmes shall: improve knowledge of the NVIS working environment and equipment; improve crew coordination; and include measures to minimise the risks associated with entry into low visibility conditions and NVIS normal and emergency procedures.

(ii)

The measures referred to in (f)(2)(i) shall be assessed during:

(A) night proficiency checks; and

(B) line checks.

The operator shall ensure that, as part of its risk analysis and management process, risks associated with the NVIS environment are minimised by specifying in the operations manual: selection, composition and training of crews; levels of equipment and dispatch criteria; and operating procedures and minima, such that normal and likely abnormal operations are described and adequately mitigated.

(a)

Helicopters shall only be operated for the purpose of CAT hoist operations if the operator has been approved by the competent authority.

(b)

To obtain such approval by the competent authority, the operator shall:

(1)

operate in CAT and hold a CAT AOC in accordance with Annex III (Part-ORO);

(2)

demonstrate to the competent authority compliance with the requirements contained in this Subpart.

(a)

The installation of all helicopter hoist equipment other than a simple PCDS, including any radio equipment to comply with point SPA.HHO.115, and any subsequent modifications, shall have an airworthiness approval appropriate to the intended function. Ancillary equipment shall be designed and tested to the appropriate standard as required by the competent authority.

(b)

Maintenance instructions for HHO equipment and systems shall be established by the operator in liaison with the manufacturer and included in the operator's helicopter maintenance programme as provided for by Regulation (EU) No 1321/2014.

Two-way radio communication shall be established with the organisation for which the HHO is being provided and, where possible, a means of communicating with ground personnel at the HHO site for:

This article is long: the rest is at the official publication.