No standard information or testing shall be required for starting substances and organic cementitious constituents where either of the following conditions are fulfilled:
a parametric value for the starting substance or organic cementitious constituent is set under Annex I to Directive (EU) 2020/2184;
a Maximum Tolerable Concentration at the tap (MTCtap) value for the starting substance or organic cementitious constituent is set in the corresponding Annex to Commission Implementing Decision (EU) 2024/367 [Commission Implementing Decision (EU) 2024/367 of 23 January 2024 laying down rules for the application of Directive (EU) 2020/2184 of the European Parliament and of the Council by establishing the European positive lists of starting substances, compositions and constituents authorised for use in the manufacture of materials or products that come into contact with water intended for human consumption (OJ L, 2024/367, 23.04.2024, ELI: http://data.europa.eu/eli/dec_impl/2024/367/oj).] following a decision by the Commission on an application for a starting substance, composition or organic cementitious constituent that has been submitted to ECHA under Article 3 of Commission Delegated Regulation (EU) 2024/369 [Commission Delegated Regulation (EU) 2024/369 of 23 January 2024 supplementing Directive (EU) 2020/2184 of the European Parliament and of the Council by laying down the procedure regarding inclusion in or removal from the European positive lists of starting substances, compositions and constituents (OJ L, 2024/369, 23.04.2024, ELI: http://data.europa.eu/eli/reg_del/2024/369/oj).] and the applicant submits at least any new or updated information available as from the date of the Commission’s decision;
a specific migration limit is set under Commission Regulation (EU) No 10/2011 [Commission Regulation (EU) No 10/2011 of 14 January 2011 on plastic materials and articles intended to come into contact with food (OJ L 12, 15.1.2011, p. 1).] for less than 15 years before the submission of an application under Article 3 of Delegated Regulation (EU) 2024/369.
2.1. Testing under this Section shall be carried out in compliance with the principles of good laboratory practice provided for in Directive 2004/10/EC of the European Parliament and of the Council [Directive 2004/10/EC of the European Parliament and of the Council of 11 February 2004 on the harmonisation of laws, regulations and administrative provisions relating to the application of the principles of good laboratory practice and the verification of their applications for tests on chemical substances (OJ L 50, 20.2.2004, p. 44).] or other international standards recognised as being equivalent to Directive 2004/10/EC by the Commission or ECHA.
2.2. Testing under this Section shall be carried out in compliance with the test method as determined and specified by ECHA and published on its website, taking into account in particular the requirements set out in point 2.5.
2.3. Column 1 of Table 1 establishes the required standard information and testing for a starting substance or organic cementitious constituent.
Column 1 of Table 1, points 4.7 and 4.8 establish the required standard information and testing for relevant chemical species other than a starting substance or organic cementitious constituent.
Column 1 of Table 1, points 4.1.3, 4.2 and 4.4 establish the required standard information and testing for a metallic, enamel, ceramic or other inorganic composition.
Column 2 of Table 1 establishes specific rules according to which the standard information and testing of column 1 may be omitted, replaced by other information, or adapted in another way.
2.4. Any other relevant physico-chemical information shall be identified and considered in addition.
2.5. Where a test method offers flexibility in the determination or choice of the study design, including by not prohibiting certain specifications, the chosen study design shall ensure that the data generated are adequate for migration testing and risk assessment.
2.6. The general rules for adaptations set out in Sections 1 and 2 of Annex XI to Regulation (EC) No 1907/2006 [Regulation (EC) No 1907/2006 of the European Parliament and of the Council of 18 December 2006 concerning the Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH), establishing a European Chemicals Agency, amending Directive 1999/45/EC and repealing Council Regulation (EEC) No 793/93 and Commission Regulation (EC) No 1488/94 as well as Council Directive 76/769/EEC and Commission Directives 91/155/EEC, 93/67/EEC, 93/105/EC and 2000/21/EC (OJ L 396, 30.12.2006, p. 1-849).] shall apply mutatis mutandis.
Column 1
Standard information and testing
Column 2
Specific rules for adaptation of the standard information and testing
4.1. | Appearance at 20 °C and 101,3 kPa |
4.1.1. | Physical state |
4.1.2. | Aggregate state (e.g., viscous, crystalline, powder) |
4.1.3. | Colour |
4.1.4. | Odour |
4.2. | Melting/freezing point | No need to provide information below a lower limit of – 20 °C.
4.3. | Boiling point |
No need to provide information for the following:
gases;
solids which either melt above 300 °C or decompose before boiling, in which case the boiling point under reduced pressure may be estimated or measured;
substances which decompose before boiling (e.g. auto-oxidation, rearrangement, degradation, decomposition, etc.).
4.4. | Density |
The study for density does not need to be conducted in the following cases:
the substance is only stable in solution in a particular solvent and the solution density is similar to that of the solvent, in which case an indication of whether the solution density is higher or lower than the solvent density is sufficient;
the substance is a gas, in which case an estimation based on calculation shall be made from its molecular weight and the Ideal Gas Laws.
4.5. | Vapour pressure |
No need to provide information if the melting point is above 300 °C.
If the melting point is between 200 °C and 300 °C, a limit value based on measurement or a recognised calculation method is sufficient.
4.5.1. | Henry’s law constant must always be stated for solids and liquids if it can be calculated. |
4.6. | Surface tension of an aqueous solution |
The information need only be provided in the following cases:
based on structure, surface activity is expected or can be predicted;
surface activity is a desired property of the material;
If the water solubility is below 1 mg/l at 20 °C, the test does not need to be conducted.
4.7. | Water solubility |
No need to provide information in the following cases:
the substance is hydrolytically unstable at pH 4, 7 and 9 (half-life less than 12 hours);
the substance is readily oxidisable in water.
If the substance appears ‘insoluble’ in water, a limit test up to the detection limit of the analytical method shall be performed.
For metals and sparingly soluble metal compounds, information on transformation/dissolution in aqueous media shall be provided.
4.8. | Partition coefficient (n-octanol/water) and its pH dependency |
No need to provide information if the substance is inorganic.
If the test cannot be performed (e.g., the substance decomposes, has a high surface activity, reacts violently during the performance of the test or does not dissolve in water or in octanol, or it is not possible to obtain a sufficiently pure substance), a calculated value for the partition coefficient as well as details of the calculation method shall be provided.
4.9. | Granulometry | The study does not need to be conducted if the substance is marketed or used in a non-solid or non-granular form.
4.10. | Dissociation constant |
No need to provide information in the following cases:
the substance is hydrolytically unstable (half-life less than 12 hours) or is readily oxidisable in water;
it is scientifically not possible to perform the test, for instance if the analytical method is not sensitive enough;
based on the structure, the substance does not have any chemical group that can dissociate.