14 ANNEX Xa, Regulation (EU) 2019/318

In forcesince 19 Feb 2019

This Annex sets out the requirements for the verification testing procedure which is the test procedure for verifying the CO2 emissions of new heavy-duty vehicles.

The verification testing procedure consists of an on-road test to verify the CO2 emissions of new vehicles after production. It shall be carried out by the vehicle manufacturer and verified by the approval authority that granted the licence to operate the simulation tool.

During the verification testing procedure the torque and speed at the driven wheels, the engine speed, the fuel consumption, the engaged gear of the vehicle and the other relevant parameters listed in point 6.1.6 shall be measured. The measured data shall be used as input to the simulation tool, which uses the vehicle-related input data and the input information from the determination of the CO2 emissions and fuel consumption of the vehicle. For the verification testing procedure simulation, the instantaneously measured wheel torque and the rotational speed of the wheels as well as the engine speed shall be used as input, as described in Figure 1 instead of the vehicle speed, in accordance with point 6.1.6. The fan power during the verification testing procedure shall be calculated in accordance with the measured fan speed. The measured fuel consumption shall be within the tolerances set out in point 7 and compared to the fuel consumption simulated with the verification data set to pass the verification testing procedure.

As part of the verification testing procedure, the correctness of the vehicle input data set from the certification of CO2 emissions and fuel consumption related properties of the components, separate technical units and systems shall also be reviewed to check the data and the data handling process. The correctness of the input data relating to components, separate technical units and systems relevant for air drag and for rolling resistance of the vehicle shall be verified in accordance with point 6.1.1.

For the purposes of this Annex the following definitions shall apply:

(1)

“verification test relevant data set” means a set of input data for components, separate technical units and systems and input information used for CO2 determination of a verification testing procedure relevant vehicle;

(2)

“verification testing procedure relevant vehicle” means a new vehicle for which a value of CO2 emissions and fuel consumption was determined and declared in accordance with Article 9;

(3)

“corrected actual mass of the vehicle” means the corrected actual mass of the vehicle in accordance with point 2(4) of Annex III;

(4)

“actual mass of the vehicle” is as defined in Article 2(6) of Regulation (EU) No 1230/2012;

(5)

“actual mass of the vehicle with payload” means the actual mass of the vehicle with the superstructure and with the payload applied in the verification testing procedure;

(6)

“wheel power” means the total power at the driven wheels of a vehicle to overcome all driving resistances at the wheel, computed in the simulation tool from the measured torque and rotational speed of the driven wheels;

(7)

“control area network signal” or “CAN signal” means a signal from the connection with the vehicle electronic control unit as referred to in paragraph 2.1.5 of Appendix 1 to Annex II to Regulation (EU) No 582/2011;

(8)

“urban driving” means the total distance driven during the fuel consumption measurement at speeds below 50 km/h;

(9)

“rural driving” means the total distance driven during the fuel consumption measurement at speeds from 50 km/h to 70 km/h;

(10)

“motorway driving” means the total distance driven in the fuel consumption measurement at speeds above 70 km/h;

(11)

“crosstalk” means the signal at the main output of a sensor (My), produced by a measurand (Fz) acting on the sensor, which is different from the measurand assigned to this output; the coordinate system assignment is defined in accordance with ISO 4130.

The number of new vehicles to be tested per year of production ensures that the relevant variations of components, separate technical units or systems used are covered by the verification testing procedure. The vehicle selection for the verification test shall be based on following requirements:

(a)

The vehicles for verification test shall be selected out of the vehicles from the production line for which a value of CO2 emissions and fuel consumption has been determined and declared in accordance with Article 9. The components, separate technical units or systems mounted in or on the vehicle shall be out of series production and shall correspond to those mounted at production date of the vehicle.

(b)

The vehicle selection shall be made by the approval authority that granted the licence to operate the simulation tool based on proposals from the vehicle manufacturer.

(c)

Only vehicles with one driven axle shall be selected for verification test.

(d)

It is recommended to include in each verification test relevant data set engine, axle and transmission with highest sales numbers per manufacturer. The components, separate technical units or systems may be tested all in one vehicle or in different vehicles, under the condition that each component is covered by minimum one verification test on one vehicle.

(e)

Vehicles which use standard values for CO2 certification of their components, separate technical units or systems instead of measured values for the transmission and for the axle losses shall not be selected for the verification test as long as vehicles complying with the requirements in points a) to c) and using measured loss maps for these components, separate technical units or systems in the CO2 certification, are produced.

(f)

The minimum number of different vehicles with different combinations of verification test relevant data sets to be tested by verification test per year shall be based on the sales numbers of the vehicle manufacturer as set out in Table 1:

Number of vehicles to be tested | Verification testing procedure relevant vehicles produced/year

1 | 1-25000

2 | 25001-50000

3 | 50001-75000

4 | 75001-100000

5 | more than 100000

(g)

The vehicle manufacturer shall finalize the verification test within a period of 10 months after the date of selection of the vehicle for the verification test.

Each vehicle for the verification test shall be in series conditions as typically delivered to the customer. No changes in hardware such as lubricants or in the software such as auxiliary controllers are allowed.

Run in of the vehicle is not mandatory. If the total mileage of the test vehicle is less than 15000 km, an evolution coefficient for the test result shall be applied as defined in point 7. The total mileage of the test vehicle shall be the odometer reading at start of the fuel consumption measurement. The maximum mileage for the verification testing procedure shall be 20000 km.

All lubricants shall be in line with the series configuration of the vehicle.

For the fuel consumption measurement as described in point 6.1.5, reference fuel as set out in point 3.2 of Annex V shall be used.

The fuel tank shall be full at start of the fuel consumption measurement run.

All laboratory reference measurement equipment, used for calibration and verification, shall be traceable to national (international) standards. The calibration laboratory shall comply with the requirements of ISO 9000 series and either ISO/TS 16949 or ISO/IEC 17025.

The direct torque at all driven axles shall be measured with one of the following measurement systems fulfilling the requirements listed in Table 2:

(a)

hub torque meter;

(b)

rim torque meter;

(c)

half-shaft torque meter.

The calibrated range shall be at least 10000 Nm; the measurement range shall cover the entire range of torque occurring during the verification testing procedure of the tested vehicle.

The drift shall be measured during the verification test described in point 6 by zeroing the torque measurement system in accordance with point 6.1.5 after the pre-conditioning phase by lifting the axle and measuring the torque at lifted axle directly after the verification test again.

For a valid test result a maximum drift of the torque measurement system over the verification testing procedure of 150 Nm (sum of both wheels) shall be proven.

The vehicle speed shall be used for possible plausibility checks of the gear signal later on and shall be based on the CAN signal.

The engaged gear does not need to be measured but shall be calculated by the simulation tool based on measured engine speed, the vehicle speed and the tyre dimensions and transmission ratios of the vehicle in accordance with point 7. The gear position may be provided also from the CAN signal to check possible deviations from the gear position calculated by the simulation tool. In case of deviations of the gear position in more than 5 % of the test duration, the reasons for the deviation shall be investigated and reported by the vehicle manufacturer. The input data on gear position shall be used in the simulation tool to compute the gear dependent losses in the gear box. The engine speed shall be taken by the simulation tool from the input data as defined in point 5.4.

The signal from the connection with the vehicle electronic control unit via the open on-board diagnostic interface shall be used to measure the engine speed. Alternative measurement systems are allowed if they fulfil the requirements set out in Table 2.

The measurement system for the rotational speed of left and right wheel at the driven axle for the assessment of the power demand at the wheels as input to the simulation tool for the verification test simulation shall fulfil the requirements set out in Table 2.

The CAN signal for the fan speed may be used, if available. Alternatively an external sensor fulfilling the requirements set out in Table 2 may be used.

The fuel consumed shall be measured on-board with a measurement device reporting the total amount of fuel consumed in kilograms. The fuel measurement system shall be based on one of the following measurement methods:

(a)

Measurement of fuel mass. The fuel measuring device shall fulfil the accuracy requirements set out in Table 2 for the fuel mass measurement system.

(b)

Measurement of fuel volume together with correction for the thermal expansion of the fuel. The fuel volume measurement device and fuel temperature measurement device shall fulfil the accuracy requirements set out in Table 2 for the fuel volume measurement system. The fuel mass consumed shall be calculated in accordance with the following equations:

mfuel

n1i1

ΔVfuel,iρi

ΔVfuel,iVfuel,i1Vfuel,i

ρi

ρ0

1βti1t0

where:

mfuelCalculated fuel mass [kg]

nTotal number of samples in measurement.

ρ0Density of the fuel used for the verification test in (kg/m3). The density shall be determined in accordance with Annex IX of the Regulation (EU) No 582/2011. If diesel fuel is used in the verification test, also the average value of the density interval for the reference fuels B7 in accordance with Annex IX of the Regulation (EU) No 582/2011 may be used.

t0Fuel temperature that corresponds to density ρ0 for the reference fuel, as defined in Annex V [°C]

ρiDensity of the test fuel at sample i [kg/m3]

Vfuel, iTotal fuel volume consumed at sample i [m3]

ti + 1Measured fuel temperature at sample i + 1 [°C]

βTemperature correction factor (0,001 K– 1).

The following masses of the vehicle shall be measured with equipment fulfilling the requirements set out in Table 2:

(a)

actual mass of the vehicle;

(b)

actual mass of the vehicle with payload.

All data shall be recorded at least in 2 Hz frequency or at recommended frequency from the equipment maker, whichever is the higher value.

The input data for the simulation tool may be composed from different recorders. The following input data shall be provided from measurements:

(a)

torque at the driven wheels per wheel;

(b)

rotational speed at the driven wheels per wheel;

(c)

gear (optional);

(d)

engine speed;

(e)

fan speed;

(f)

vehicle speed;

(g)

fuel flow.

The torque and rotational speed at the wheels shall be recorded in one data-logging system. If different data-logging systems are used for the other signals, one common signal, such as vehicle speed, shall be recorded to ensure correct time alignment of the signals.

The accuracy requirements set out in Table 2 shall be met by all measurement equipment used. Any equipment not listed in Table 2 shall fulfil the accuracy requirements set out in Table 2 of Annex V.

[Rise time means the difference in time between the 10 percent and 90 percent response of the final analyser reading (t90 – t10).] [The accuracy shall be met for the integral fuel flow over 100 minutes.]

Measurement system | Accuracy | Rise time

Balance for vehicle weight |

50 kg or

< 0,5 % of max. calibration

whichever is smaller

—

Rotational speed wheels | < 0,5 % of max. calibration | ≤ 1 s

Fuel mass flow for liquid fuels |

< 1,0 % of reading or

< 0,5 % of max. calibration

whichever is larger

≤ 2 s

Fuel volume measurement system |

< 1,0 % of reading or

< 0,5 % of max. calibration

whichever is larger

≤ 2 s

Temperature of the fuel | ± 1 °C | ≤ 2 s

Sensor for measuring the rotational speed cooling fan | 0,4 % of reading or 0,2 % of max. calibration of speed whichever is larger | ≤ 1 s

Engine speed | As set out in Annex V

Wheel torque |

For 10 kNm calibration:

< 40 Nm accuracy

< 20 Nm crosstalk

< 0,1 s

The maximum calibration values shall be at least 1,1 times the maximum predicted value expected during all test runs for the respective measurement system. For the torque measurement system the maximum calibration may be limited to 10 kNm.

Accuracy given shall be met by the sum of all single accuracies in the case more than one scale is used.

The vehicle shall be taken from the series production and selected as set out in point 3.

The manufacturer's records file for the vehicle selected shall be used as basis for validating the input data. The vehicle identification number of the vehicle selected shall be the same as the vehicle identification number in the customer information file.

Upon request by the approval authority that granted the licence to operate the simulation tool, the vehicle manufacturer shall provide, within 15 working days, the manufacturer's records file, the input information and input data necessary to run the simulation tool as well as the certificate of CO2 emissions and fuel consumption related properties for all relevant components, separate technical units or systems.

The following checks shall be performed for the components, separate technical units and systems mounted on the vehicle:

(a)

Simulation tool data integrity: the integrity of the cryptographic hash of the manufacturer's records file in accordance with Article 9(3) re-calculated during the verification testing procedure with the hashing tool shall be verified by comparison with the cryptographic hash in the certificate of conformity;

(b)

Vehicle data: the vehicle identification number, axle configuration, selected auxiliaries and power take off technology shall match the selected vehicle;

(c)

Component, separate technical unit or system data: the certification number and the model type imprinted on the certificate of CO2 emissions and fuel consumption related properties shall match the component, separate technical unit or system installed in the selected vehicle;

(d)

The hash of the simulation tool input data and the input information shall match the hash imprinted on the certificate of CO2 emissions and fuel consumption related properties for the following components, separate technical units or systems:

(i)

engines;

(ii)

transmissions;

(iii)

torque converters;

(iv)

other torque transferring components;

(v)

additional driveline components;

(vi)

axles;

(vii)

body or trailer air drag;

(viii)

tyres.

If requested by the approval authority that granted the licence to operate the simulation tool, a verification of the corrected actual mass of the vehicle shall be included into the verification of input data.

For the verification of the mass, the mass in running order of the vehicle shall be verified in accordance with point 2 of Appendix 2 to Annex I to Regulation (EC) No 1230/2012.

In case of discrepancies in the certification number or the cryptographic hash of one or more files regarding the components, separate technical units or systems listed in subpoints (d)(i) to (vii) of point 6.1.1.1 the correct input data file fulfilling the checks in accordance with points 6.1.1.1 and 6.1.1.2 shall replace the incorrect data for all further actions. If no complete input data set with correct certificates of CO2 emissions and fuel consumption related properties is available for the components, separate technical units or systems listed in subpoints (d)(i) to (vii) of point 6.1.1.1 the verification test shall end and the vehicle fails the verification testing procedure.

After the validation of input data in accordance with point 6.1.1, a run in phase up to maximum 15000 km odometer reading may take place, with no need to use the reference fuel, if the odometer reading of the vehicle selected is below 15000 km. In case of damage of any of the components, separate technical units or systems listed in point 6.1.1.1, the component, separate technical units or systems may be replaced by an equivalent component, separate technical units or systems with the same certification number. The replacement shall be documented in the test report.

All relevant components, separate technical units or systems shall be checked before the measurements to exclude unusual conditions, such as incorrect oil fill levels, plugged air filters or on-board diagnostic warnings.

All measurement systems shall be calibrated in accordance with the provisions of the equipment maker. If no provisions exist, the recommendations from the equipment maker shall be followed for calibration.

After the run in phase, the vehicle shall be equipped with the measurement systems set out in point 5.

Tractors of the vehicle groups defined in Table 1 of Annex I shall be tested with any type of semitrailer, providing the loading defined below can be applied.

Rigid lorries of the vehicle groups defined in Table 1 of Annex I shall be tested with trailer, if a trailer connection is mounted. Any body type or other device to carry the loading set out below can be applied.

The bodies of the vehicles may differ from the standard bodies set out in Table 1 of Annex I for the certification of CO2 emissions and fuel consumption related properties of component, separate technical units or systems.

The vehicle payload shall be at minimum to a mass leading to a total test weight of 90 % of the maximum gross combined weight or gross vehicle weight for rigid lorries without trailer.

The tyre inflation pressure shall be in line with the recommendation of the manufacturer. The tyres of the semitrailer may differ from the standard tyres set out in Table 2 of Part B of Annex II to Regulation (EC) No 661/2009 for the CO2 certification of tyres.

All settings influencing the auxiliary energy demand shall be set to minimum reasonable energy consumption where applicable. The air conditioning shall be switched off and venting of the cabin shall be set lower than medium mass flow. Additional energy consumers not necessary to run the vehicle shall be switched off. External devices to provide energy on board, such as external batteries, are allowed only for running the extra measurement equipment for the verification testing procedure listed in Table 2 but shall not provide energy to serial vehicle equipment.

A particle filter regeneration may be initiated and shall be achieved before the verification test. If an initiated particle filter regeneration cannot be achieved before the verification test, the test is invalid and shall be repeated.

The route selected for the verification test shall fulfil the requirements set out in Table 3. The routes may include both public and private tracks.

No specific pre-conditioning of the vehicle is required.

Before the fuel consumption measurement starts, the vehicle shall be driven for warm up as set out in Table 3. The warm up phase shall not be considered in the evaluation of the verification test.

Zeroing of the torque measurement equipment shall follow the instruction of the equipment maker. It shall be ensured for zeroing, that the torque on the driven axle is zero. For zeroing, the vehicle shall be stopped directly after the warm up phase and zeroing shall be performed directly after the vehicle stop to minimise cool down effects. Zeroing shall be finished within less than 20 minutes.

The fuel consumption measurement shall start directly after the zeroing of the wheel-torque measurement equipment at vehicle stand still and engine idling. The vehicle shall be driven during the measurement in a driving style avoiding unnecessary braking of the vehicle, gas pedal pumping and aggressive cornering. The setting for the electronic control systems which is activated automatically at vehicle start shall be used, and gear shifts shall be performed by the automated system if applicable. If only manual settings for the electronic control systems are available, the settings leading to higher fuel consumption per kilometre shall be selected. The duration of the fuel consumption measurement shall be within the tolerances set out in Table 3. The fuel consumption measurement shall end also at vehicle stand still in idling condition directly before the measurement of the drift of the torque measurement equipment.

Directly after the fuel consumption measurement, the drift of the torque measurement equipment shall be recorded by measuring the torque at the same vehicle conditions as during the zeroing process. If the fuel consumption measurement does not end at zero vehicle speed, the vehicle shall be stopped for the drift measurement in moderate deceleration.

The boundary conditions to be met for a valid verification test are set in Table 3.

If the vehicle passes the verification test in accordance with point 7, the test shall be set valid even if the following conditions are not met:

undercut of minimum values for parameter No 1, 2, 6, 9 in Table 3,

exceedance of maximum values for parameter No 3, 4, 5, 7, 8, 10, 12 in Table 3.

[Or maximum vehicle speed if lower than 70 km/h]

No | Parameter | Min. | Max. | Applicable for

1 | Warm up [minutes] | 60 | |

2 | Average velocity at warm up [km/h] | 70 | 100 |

3 | Fuel consumption measurement duration [minutes] | 80 | 120 |

4 | Distance based share urban driving | 2 % | 8 % | vehicle groups 4, 5, 9, 10

5 | Distance based share rural driving | 7 % | 13 % |

6 | Distance based share motorway driving | 74 % | — | vehicle groups 4, 5, 9, 10

7 | Time share of idling at stand still | | 5 % |

8 | Average ambient temperature | 5 °C | 30 °C |

9 | Road condition dry | 100 % | |

This article is long: the rest is at the official publication.