Annexes IV and XII to Delegated Regulation (EU) No 44/2014 are amended as follows:
In Annex IV, points 4.1.1.3.1.1.1.1.1., 4.1.1.3.1.1.1.1.2. and 4.1.1.3.1.1.1.1.3. are replaced by the following:
‘4.1.1.3.1.1.1.1.1. If the durability method set out in Article 23(3)(a) of Regulation (EU) No 168/2013 is applicable, the deterioration factors shall be calculated from the type I emission test results up to and including full distance referred to in Annex VII(A) to Regulation (EU) No 168/2013 and in accordance with the linear calculation method referred to in point 4.1.1.3.1.1.1.1.2. resulting in slope and offset values per emission constituent. The CoP pollutant emission results shall be calculated with the formula:
Yfull = a (Xfull – XCoP) + YCoP
where:
aslope value ((mg/km)/km) determined in accordance with test type V set out in Annex V(A) to Regulation (EU) No 168/2013;
XFulldurability mileage (km) as set out in Annex VII to Regulation (EU) No 168/2013;
XCoPMileage of the CoP vehicle at moment of Type I CoP test;
YfullCoP emission result per pollutant emission constituent in mg/km. The average CoP results shall be lower than the pollutant emission limits set out in Annex VI(A) to Regulation (EU) No 168/2013;
YCoPpollutant emission (THC, CO, NOx, NMHC and PM if applicable) test result (mg/km) per emission constituent of test type I with CoP vehicle.
4.1.1.3.1.1.1.1.2 If the durability method set out in Article 23(3)(b) of Regulation (EU) No 168/2013 is applicable, the deterioration trend shall consist of the slope value a, as is reflected in point 4.1.1.3.1.1.1.1.1, per emission constituent calculated to comply with test type V in accordance with Annex V(A) to Regulation (EU) No 168/2013. Equation 4-1 shall be used to calculate the CoP emission results per pollutant emission constituent (Yfull).
4.1.1.3.1.1.1.1.3. If the durability method set out in Article 23(3)(c) of Regulation (EU) No 168/2013 is applicable, the fixed deterioration factors set out in Annex VII(B) to Regulation (EU) No 168/2013 shall be multiplied by the type test I result of the CoP vehicle (Ycop) to calculate the average CoP emission results per pollutant emission constituent (Yfull).’.
Annex XII is amended as follows:
the following point 3.2.3.is inserted:
‘3.2.3.
Identification of deterioration or malfunctions may also be done outside a driving cycle (e.g. after engine shutdown).’;
point 3.3.2.2. is replaced by the following:
The presence of engine misfire in the engine operating region bounded by the following lines:
low speed limit: A minimum speed of 2500 min– 1 or normal idle speed + 1000 min– 1, whichever is the lower
high speed limit: A maximum speed of 8000 min– 1 or 1000 min– 1 greater than the highest speed occurring during a type I test cycle or maximum design engine speed minus 500 min– 1, whichever is lower
a line joining the following engine operating points:
a point on the low speed limit defined in (a) with the engine intake vacuum at 3,3 kPa lower than that at the positive torque line;
a point on the high speed limit defined in (b) with the engine intake vacuum at 13,3 kPa lower than that at the positive torque.
The engine operation region for misfire detection is reflected in Figure 10-1.
’;
the following point 3.10. is inserted:
‘3.10.
Additional provisions for vehicles employing engine shut-off strategies.
3.10.1.1.
Autonomous engine restarts commanded by the engine control system following an engine stall may be considered a new driving cycle or a continuation of the existing driving cycle.’;
Appendix 1 is amended as follows:
point 3.2. is replaced by the following:
‘3.2.
If available, the following signals in addition to the required freeze-frame information shall be made available on demand through the serial port on the standardised diagnostic connector, if the information is available to the on-board computer or can be determined using information available to the on-board computer: diagnostic trouble codes, engine coolant temperature, fuel control system status (closed-loop, open-loop, other), fuel trim, ignition timing advance, intake air temperature, manifold air pressure, air flow rate, engine speed, throttle position sensor output value, secondary air status (upstream, downstream or atmosphere), calculated load value, vehicle speed and fuel pressure.
The signals shall be provided in standard units based on the specifications in point 3.7. Actual signals shall be clearly identified separately from default value or limp-home signals.’;
points 3.11., 3.12. and 3.13 are replaced by the following:
‘3.11.
When a fault is registered, the manufacturer shall identify the fault using an appropriate fault code consistent with those in ISO 15031-6:2010 ‘Road vehicles — Communication between vehicle and external test equipment for emissions-related diagnostics — Part 6: Diagnostic trouble code definitions’ relating to ‘emission-related system diagnostic trouble codes’. If this is not possible, the manufacturer may use the diagnostic trouble codes of ISO DIS 15031-6:2010. Alternatively, fault codes may be compiled and reported in accordance with ISO14229:2006. The fault codes shall be fully accessible by standardised diagnostic equipment complying with point 3.9.
The vehicle manufacturer shall provide to a national standardisation body the details of any emission-related diagnostic data, e.g. PID's, OBD monitor Id's, Test Id's not specified in ISO 15031-5:2011 or ISO14229:2006, but relating to this Regulation.
3.12.
The connection interface between the vehicle and the diagnostic tester shall be standardised and meet all the requirements of ISO 19689:2016 ‘Motorcycles and mopeds — Communication between vehicle and external equipment for diagnostics — Diagnostic connector and related electrical circuits, specification and use’ or ISO 15031-3:2004 ‘Road vehicles — Communication between vehicle and external test equipment for emissions-related diagnostics — Part 3: Diagnostic connector and related electric circuits: specification and use’. The preferred installation position is under the seating position. Any other position of the diagnostic connector shall be subject to the approval authority's agreement and be readily accessible by service personnel but protected from tampering by non-qualified personnel. The position of the connection interface shall be clearly indicated in the user manual.
3.13.
Until an OBD stage II system for L-category vehicle has been implemented on the vehicle, an alternative connection interface may be installed at the request of the vehicle manufacturer. Where such an alternative connection interface is installed, the vehicle manufacturer shall make available to test equipment manufacturers the details of the vehicle connector pin configuration free of charge. The vehicle manufacturer shall provide an adapter enabling connection to a generic scan tool. Such an adapter shall be of suitable quality for professional workshop use. It shall be provided upon request to all independent operators in a non-discriminating manner. Manufacturers may charge a reasonable and proportionate price for this adapter, taking into account the additional costs caused for the customer by this choice of the manufacturer. The connection interface and the adapter may not include any specific design elements which would require validation or certification before use, or which would restrict the exchange of vehicle data when using a generic scan tool.’;
point 4.1.4. is replaced by the following:
‘4.1.4.
From 1 January 2024, if, in accordance with the requirements of this Annex, the vehicle is equipped with a specific monitor M, IUPRM shall be greater than or equal to 0,1 for all monitors M.’;
the following point 4.1.4.1. is inserted:
‘4.1.4.1.
Until 31 December 2023, the manufacturer shall demonstrate to the approval authority the functionality of IUPR determination, for new types of vehicles as of 1 January 2020 and for existing types of vehicles as of 1 January 2021.’;
point 4.5. and 4.5.1.is replaced by the following:
4.5.1.
The general denominator is a counter measuring the number of times a vehicle has been operated. It shall be incremented within 10 seconds, if the following criteria are satisfied on a single driving cycle:
Cumulative time since engine start is greater than or equal to 600 seconds at an elevation of less than 2440 m above sea level or an ambient pressure of more than 75,7 kPa and an ambient temperature of 266,2 K (– 7 °C) or more;
Cumulative vehicle operation at or above 25 km/h occurs for 300 seconds or more at an elevation of less than 2440 m above sea level or an ambient pressure of more than 75,7 kPa and an ambient temperature of 266,2 K (– 7 °C) or more;
Continuous vehicle operation at idle (i.e. accelerator pedal released by driver and vehicle speed of 1,6 km/h or less) for 30 seconds or more at an elevation of less than 2440 m above sea level or an ambient pressure of more than 75,7 kPa and an ambient temperature of 266,2 K (– 7 °C) or more.
The general denominator may also be incremented outside the boundary conditions for altitude or ambient pressure and ambient temperature.’;
the following point 4.6.2.1. is inserted:
‘4.6.2.1.
Numerators and denominators for specific monitors of components or systems that are monitoring continuously for short circuit or open circuit failures are exempted from reporting.
For the purposes of this point, “continuously” means monitoring is always enabled and sampling of the signal used for monitoring occurs at a rate no less than two samples per second and the presence or the absence of the failure relevant to that monitor has to be concluded within 15 seconds. If for control purposes, a computer input component is sampled less frequently, the signal of the component may instead be evaluated each time sampling occurs.It is not required to activate an output component/system for the sole purpose of monitoring that output component/system.’;
point 4.7.4. is replaced by the following:
‘4.7.4.
The OBD system shall disable further incrementing of the general denominator within 10 seconds if a malfunction has been detected of any component used to determine whether the criteria in point 4.5 are satisfied (i.e. vehicle speed, ambient temperature, elevation, idle operation or time of operation) and the corresponding pending fault code has been stored. The general denominator may not be disabled from incrementing for any other condition. Incrementing of the general denominator shall resume within 10 seconds when the malfunction is no longer present (e.g. pending code erased through self-clearing or by a scan tool command).’;
Appendix 2 is amended as follows:
in point 1, the footnote is deleted;
point 2.1. is replaced by the following;
[Only in case of an activated default mode leading to a significantly reduced propulsion torque or if a throttle by wire system is fitted.] [If redundant APS or redundant TPS are fitted, signal cross check(s) shall meet all circuit rationality requirements. If there is only one APS or TPS fitted, APS or TPS circuit rationality monitoring is not mandatory.]
Deleted.
[OBD stage II: two out of three of the circuit rationality malfunctions marked with ‘II’ shall be monitored in addition to circuit continuity monitoring.] [only if used as input to ECU/PCU with relevance to environmental or functional safety performance.] [Derogation allowed if manufacturer requests, level 3 instead, actuator signal present only without indication of symptom.’;]
No | Device circuits | | Circuit continuity | Circuit rationality | Basic monitoring requirement | Comment No
Level, refer to 2.3 | Circuit High | Circuit Low | Open Circuit | Out of Range | Performance/Plausibility | Signal stuck | Device not operational / Device not present |
1 | Control module (ECU/PCU) internal error | 3 | | | | | | | I&II |
Sensor (input to control units)
1 | Accelerator (pedal/handle) position sensor | 1 | I&II | I&II | I&II | I&II | I&II | I&II | |
2 | Barometric pressure sensor | 1 | I&II | I&II | I&II | | II | | |
3 | Camshaft position sensor | 3 | | | | | | | I&II |
4 | Crankshaft position sensor | 3 | | | | | | | I&II |
5 | Engine coolant temperature sensor | 1 | I&II | I&II | I&II | II | II | II | |
6 | Exhaust control valve angle sensor | 1 | I&II | I&II | I&II | II | II | II | |
7 | Exhaust gas recirculation sensor | 1 | II | II | II | II | II | II | |
8 | Fuel rail pressure sensor | 1 | I&II | I&II | I&II | II | II | II | |
9 | Fuel rail temperature sensor | 1 | I&II | I&II | I&II | II | II | II | |
10 | Gear shift position sensor (potentiometer type) | 1 | I&II | I&II | I&II | II | II | II | |
11 | Gear shift position sensor (switch type) | 3 | | | | | II | | I&II |
12 | Intake air temperature sensor | 1 | I&II | I&II | I&II | II | II | II | |
13 | Knock sensor (Non-resonance type) | 3 | | | | | | | I&II |
14 | Knock sensor (Resonance type) | 3 | | | | | I&II | | |
15 | Manifold absolute pressure sensor | 1 | I&II | I&II | I&II | II | II | II | |
16 | Mass air flow sensor | 1 | I&II | I&II | I&II | II | II | II | |
17 | Engine oil temperature sensor | 1 | I&II | I&II | I&II | II | II | II | |
18 | O2 sensor (binary/linear) signals | 1 | I&II | I&II | I&II | II | II | II | |
19 | Fuel (high) pressure sensor | 1 | I&II | I&II | I&II | II | II | II | |
20 | Fuel storage temperature sensor | 1 | I&II | I&II | I&II | II | II | II | |
21 | Throttle position sensor | 1 | I&II | I&II | I&II | I&II | I&II | I&II | |
22 | Vehicle speed sensor | 3 | | | | | II | | I&II |
23 | Wheel speed sensor | 3 | | | | | II | | I&II |
Actuators (output control units)
1 | Evaporative emission system purge control valve | 2 | II | I&II | II | | | | I&II |
2 | Exhaust control valve actuator (motor driven) | 3 | | | | | II | | I&II |
3 | Exhaust gas recirculation control | 3 | | | | | II | | |
4 | Fuel injector | 2 | | I&II | | | | | I&II |
5 | Idle air control system | 1 | I&II | I&II | I&II | | II | | I&II |
6 | Ignition coil primary control circuits | 2 | | I&II | | | | | I&II |
7 | O2 sensor heater | 1 | I&II | I&II | I&II | | II | | I&II |
8 | Secondary air injection system | 2 | II | I&II | II | | | | I&II |
9 | Throttle by wire actuator | 3 | | I&II | | | | | I&II |
point 2.4 is replaced by the following
‘2.4.
Two out of three symptoms in circuit continuity as well as in circuit rationality monitoring diagnostic may be combined, e.g.
circuit high or open and low circuit;
high and low or open circuit;
signal out of range or circuit performance and signal stuck;
circuit high and out of range high or circuit low and out of range low.’;
the following Appendices 3, 4 and 5 are added:
‘’