1.1.
This Appendix sets out the criteria referred to in Section 4 of Appendix 1 to this annex regarding the selection of vehicles for testing and the procedures for IUPR M.
The criteria for acceptance of a selected vehicle are defined for IUPR M in Sections 2.1. to 2.5.
2.1.
The vehicle shall belong to a vehicle type that is type-approved under this Regulation and covered by a certificate of conformity in accordance with Implementing Regulation (EU) No 901/2014 [Commission Implementing Regulation (EU) No 901/2014 of 18 July 2014 implementing Regulation (EU) No 168/2013 of the European Parliament and of the Council with regard to the administrative requirements for the approval and market surveillance of two- or three-wheel vehicles and quadricycles (OJ L 249, 22.8.2014, p. 1).]. For checking of IUPR M, the vehicle shall be approved to the OBD standard stage II or later. It shall be registered and have been used in the Union.
2.2.
The vehicle shall have been in service for at least 3000 km or 6 months, whichever is the later, and for no more than the durability mileages given for the relevant vehicles category mentioned in Annex VII(A) to Regulation (EU) No 168/2013 or 5 years, whichever is the sooner.
2.3.
For checking IUPR M, the test sample shall include only vehicles that:
have collected sufficient vehicle operation data for the monitor to be tested.
For monitors required to meet the in-use monitor performance ratio and to track and report ratio data pursuant to point 4.6.1. of Appendix 1, sufficient vehicle operation data shall mean the denominator meets the criteria set forth below. The denominator, as defined in points 4.3 and 4.5 of Appendix 1, for the monitor to be tested must have a value equal to or greater than one of the following values:
15 for evaporative system monitors, secondary air system monitors, and monitors utilising a denominator incremented in accordance with point 4.3.2. of Appendix 1 (e.g. cold start monitors, air conditioning system monitors, etc.); or
5 for particulate filter monitors and oxidation catalyst monitors utilising a denominator incremented in accordance with point 4.3.2. of Appendix 1; or
30 for catalyst, oxygen sensor, EGR, VVT, and all other component monitors.
have not been tampered with or equipped with add-on or modified parts that would cause the OBD system not to comply with the requirements of Annex XII.
2.3.
If any service has taken place, it shall be to the manufacturer's recommended service intervals.
2.4.
The vehicle shall exhibit no indications of abuse (e.g. racing, overloading, mis-fuelling, or other misuse), or other factors (e. g. tampering) that could affect emission performance. The fault code and mileage information stored in the computer shall be taken into account. A vehicle shall not be selected for testing if the information stored in the computer shows that the vehicle has operated after a fault code was stored and a relatively prompt repair was not carried out.
2.5.
There shall have been no unauthorised major repair to the engine or major repair of the vehicle.
3.1.
The type approval authority shall request the manufacturer to submit a plan of remedial measures to remedy the non-compliance when:
3.2.
For IUPRM of a particular monitor M the following statistical conditions are met in a test sample, the size of which is determined in accordance with point 3.3.1. of Appendix 3.
For vehicles certified to a ratio of 0,1 in accordance with point 4.1.4. of Appendix 1, the data collected from the vehicles indicate for at least one monitor M in the test sample either that the test sample average in-use-performance ratio is less than 0,1 or that 66 per cent or more of the vehicles in the test sample have an in-use monitor performance ratio of less than 0,1.
3.3.
The plan of remedial measures shall be filed with the type approval authority not later than 60 working days from the date of the notification referred to in point 3.1. The type approval authority shall within 30 working days declare its approval or disapproval of the plan of remedial measures. However, where the manufacturer can demonstrate, to the satisfaction of the competent type approval authority, that further time is required to investigate the non-compliance in order to submit a plan of remedial measures, an extension is granted.
3.4.
The remedial measures shall apply to all vehicles likely to be affected by the same defect. The need to amend the type approval documents shall be assessed.
3.5.
The manufacturer shall provide a copy of all communications related to the plan of remedial measures, and shall also maintain a record of the recall campaign, and supply regular status reports to the type approval authority.
3.6.
The plan of remedial measures shall include the requirements specified in points 3.6.1. to 3.6.11. The manufacturer shall assign a unique identifying name or number to the plan of remedial measures.
3.6.1.
A description of each vehicle type included in the plan of remedial measures.
3.6.2.
A description of the specific modifications, alterations, repairs, corrections, adjustments, or other changes to be made to bring the vehicles into conformity including a brief summary of the data and technical studies which support the manufacturer's decision as to the particular measures to be taken to correct the non-conformity.
3.6.3.
A description of the method by which the manufacturer informs the vehicle owners.
3.6.4.
A description of the proper maintenance or use, if any, which the manufacturer stipulates as a condition of eligibility for repair under the plan of remedial measures, and an explanation of the manufacturer's reasons for imposing any such condition. No maintenance or use conditions may be imposed unless it is demonstrably related to the non-conformity and the remedial measures.
3.6.5.
A description of the procedure to be followed by vehicle owners to obtain correction of the non-conformity. This shall include a date after which the remedial measures may be taken, the estimated time for the workshop to perform the repairs and where they can be done. The repair shall be done expediently, within a reasonable time after delivery of the vehicle.
3.6.6.
A copy of the information transmitted to the vehicle owner.
3.6.7.
A brief description of the system which the manufacturer uses to assure an adequate supply of component or systems for fulfilling the remedial action. It shall be indicated when there will be an adequate supply of components or systems to initiate the campaign.
3.6.8.
A copy of all instructions to be sent to those persons who are to perform the repair.
3.6.9.
A description of the impact of the proposed remedial measures on the emissions, fuel consumption, driveability, and safety of each vehicle type, covered by the plan of remedial measures with data, technical studies, etc. which support these conclusions.
3.6.10.
Any other information, reports or data the type approval authority may reasonably determine is necessary to evaluate the plan of remedial measures.
3.6.11.
Where the plan of remedial measures includes a recall, a description of the method for recording the repair shall be submitted to the type approval authority. If a label is used, an example of it shall be submitted.
3.7.
The manufacturer may be required to conduct reasonably designed and necessary tests on components and vehicles incorporating a proposed change, repair, or modification to demonstrate the effectiveness of the change, repair, or modification.
3.8.
The manufacturer is responsible for keeping a record of every vehicle recalled and repaired and the workshop which performed the repair. The type approval authority shall have access to the record on request for a period of 5 years from the implementation of the plan of remedial measures.
3.9.
The repair and/or modification or addition of new equipment shall be recorded in a certificate supplied by the manufacturer to the vehicle owner.